Bedienungsanleitung Chamberlain CIGCWC - MyQ (Seite 1 von 8) (Englisch)

555427

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

INTERNET CONNECTIVITY KIT

MODEL CIGCWC

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.

• Connect ONLY to 7-28 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing

garage door:

• Install door control within sight of garage door, out of reach of

children at a minimum height of 5 feet (1.5 m), and away from ALL

moving parts of door.

• NEVER permit children to operate or play with door control push

buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

• DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light

bulb(s) MUST be a minimum of 40 Watt (or equivalent).

This kit includes the MyQ

Control Panel model 41A7928-3 and the

Chamberlain

Internet Gateway model CIGBU. The MyQ

Control Panel is

intended to be installed with Security✚™ Garage Door Openers

manufactured between 1998 and present. The MyQ

Control Panel is NOT

compatible with Security✚ 2.0™ Garage Door Openers. DO NOT install

this door control on garage door opener systems controlling one-piece or

swing doors.

APPLICATION

The MyQ

Control Panel offers a quick and convenient way to add

Security✚ 2.0™ and MyQ

technology to your existing garage door

opener. MyQ

technology uses a 900MHz signal to provide two-way

communication between the garage door opener and MyQ

enabled

accessories. When programmed to the Chamberlain

Internet Gateway

you can monitor and control your garage door from any internet enabled

computer or smartphone. You may program up to 12 Security✚ 2.0™

remote controls, 2 Security✚ 2.0™ keyless entries and a combination of

16 MyQ

accessories to the MyQ

control panel. For full compatibility,

see page 4.

OVERVIEW

Install the control panel in place of the existing door control. Due to

power consumption the control panel cannot be used in conjunction with

another wired door control connected to your garage door opener. If an

additional door control is needed, the wireless door control model

41A7773-1 can be programmed to the control panel. To program the

41A7773-1 to the control panel, follow the remote control programming

steps. When in battery back-up mode, any feature using unattended

operation such as Timer-to-Close, closure from a garage door and gate

monitor or remote operation utilizing the Chamberlain

Internet Gateway

will be disabled.

1. Disconnect all electrical and battery power (if applicable) to the

garage door opener.

2. Remove the existing door control from the wall.

3. Note the polarity of the wires connected to the existing door

control.

• Label the wire connected to the RED terminal.

• Label the wire connected to the WHITE terminal.

Disconnect the wires from the existing door control.

4. Connect the wires to the new MyQ

Control Panel. Make sure the

polarity is correct.

• Red wire to the R terminal.

• White wire to the W terminal.

5. Mount the control panel to the wall.

6. Reconnect power. The yellow command LED and the red learn LED

will blink quickly for up to 5 minutes as the control panel

recharges. When the control panel is operational, the yellow

command LED will glow steadily.

7. To test the control panel, press the push bar to activate the garage

door opener.

INSTALL THE MyQ

CONTROL PANEL

Existing Door Control

Discard, donate

or recycle

Wire from

RED terminal

Connect

RED wire to

R terminal

Wire from

WHITE

terminal

Connect

WHITE

wire to W

terminal

MyQ

Control Panel

• If the yellow command LED does not turn on, reverse the wires

connected to the R and W terminals of the control panel. Replace

wire if necessary.

• If yellow and red LEDs are blinking slowly, the control panel is not

compatible with your garage door opener.

• If the yellow and red LEDs are blinking quickly, the control panel is

charging, and may take up to 5 minutes to become operational.

TROUBLESHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Chamberlain CIGCWC - MyQ Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info