Bedienungsanleitung Charlton Jenrick Fireline Woodtec 5 (Seite 6 von 28) (Englisch)

707656

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

5 Woodtec Freestanding Issue 01.1 05/17

3.0 Preparation of Stove for Installation.

Your stove comes fully assembled, checked and packed in a protective plywood crate.

Carefully cut and remove the straps and lift off the top and upper crate. Remove any

plastic packaging, open the door and remove all the contents. See List of Components

section (above) and check contents carefully.

**IMPORTANT HANDLING WARNING!!**

NEVER TIP OR ROCK THE STOVE FORWARDS DURING HANDLING AS IT MAY DAMAGE THE

AIR CONTROL LEVER!

3.1. Remove the stove door if required for easier handling of the unit. Open the door,

remove the fixing screws from the bottom hinge and lower the door downwards to

disengage the upper hinge pin. When re-assembling use the same shims that were

factory fitted and make sure that the door is correctly tightened in line with the stove

body.

3.2. Remove the interior components of the stove using the following procedure. SEE ALSO

MAINTENANCE GUIDE section for diagrams where required.

3.2.1. Remove the baffle plate by supporting the plate with both hands and lifting the

front edge upwards towards you and sliding the back edge off the back support and

down slightly into the firebox. Once the rear is lowered then the front edge can also

be lowered off the front baffle supports.

3.2.2. Next remove the two cast ceramic firebox side liners by carefully shifting the

front edges inwards towards the centre of the firebox and sliding forwards away

from the 45 degree mitre joint with the back liner at the rear corners. Take great

care not to chip or damage the surfaces of these ceramic components – support the

rear liner so that it cannot fall over and break!

3.2.3. Now remove the firebox rear liner. Handle and store these ceramic liners very

carefully to one side where they will not get broken.

3.2.4. Remove the firebox base ceramic from the firebox by lifting and tilting.

3.3. Rock the stove to the left and right side in turn and set the adjustable feet of the stove

to approximately their required position. They can be re-adjusted lower later if

required. NOTE: DO NOT rock the stove forward as it may damage the air control

lever!

3.4. The flue spigot collar may now be configured for horizontal connection if required.

3.4.1. Remove the 4 x M6 cap screws in the upper rear firebox and remove the spigot.

3.4.2. Remove the rear casing by levering away from the body at the top with a

screwdriver at the same time as lifting the panel upwards.

3.4.3. The rear casing blanking plate can now be taken out by carefully knocking it out

from the back panel by breaking the provided laser cut micro joints.

3.4.4. Re-fit the back panel before re-fitting the flue spigot.

3.4.5. Finally the spigot may then be rotated by 180 degrees and re-fitted either using

the gasket provided or re-sealing with fire cement as required.

3.4.6. The casing blanking plate can now be used to cover the hole in the top plate.

3.5. Lift the stove into its final position using an assistant to help.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charlton Jenrick Fireline Woodtec 5 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info