Zoom out
Zoom in
Vorherige Seite
1/316
Nächste Seite
Cisco Systems, Inc.
www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.
Cisco 800 Series Integrated Services
Router Hardware Installation Guide
July 31, 2016
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    Cisco 800 Series Integrated Services
    Router Hardware Installation Guide
    July 31, 2016

    Cisco Systems, Inc.
    www.cisco.com
    Cisco has more than 200 offices worldwide.
    Addresses, phone numbers, and fax numbers
    are listed on the Cisco website at
    www.cisco.com/go/offices.



  • Page 2

    THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
    STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
    WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
    THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
    SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
    OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
    The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
    to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
    environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
    harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
    to correct the interference at their own expense.
    The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
    to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
    uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
    However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be
    determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:





    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.

    Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.
    The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
    domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
    NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
    ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
    LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
    DEALING, USAGE, OR TRADE PRACTICE.
    IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
    WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
    OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
    Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
    URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
    relationship between Cisco and any other company. (1721R)
    Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display
    output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in
    illustrative content is unintentional and coincidental.
    Cisco 800 Series Integrated Services Router Hardware Installation Guide
    © 2016 Cisco Systems, Inc. All rights reserved.



  • Page 3

    CONTENTS
    Preface

    vii

    Objective

    vii

    Audience

    vii

    Organization

    viii

    Conventions

    viii

    Related Documentation

    xvi

    Searching Cisco Documents

    xvi

    Obtaining Documentation and Submitting a Service Request
    Product Overview

    xvi

    1-1

    Cisco 810 Series 1-1
    Cisco 812 Series 1-1
    General Description 1-1
    Hardware Features 1-4
    SKU Information 1-9
    Cisco 819 Series 1-10
    General Description 1-10
    SKU Information 1-14
    Hardware Features 1-23
    Cisco 860, 880, 890 Series 1-38
    General Description 1-39
    Cisco 860 Series ISRs 1-39
    Cisco 860VAE Series ISRs 1-41
    Interfaces 1-41
    IOS Images 1-41
    Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and
    Cisco 860VAE-POE-W-A-K9 ISRs 1-43
    Model-Specific Features 1-43
    Common Features 1-44
    Cisco 880 Series ISRs 1-47
    Cisco 880 Series Data Routers 1-48
    Cisco 880 Series Voice and Data Routers 1-51
    Cisco 880 Series with Embedded WLAN Antennas
    C881G-B/S/V-K9 ISRs 1-59
    C881GW-S/V-A-K9 ISRs 1-59

    1-57

    Cisco Integrated Services Router Hardware Installation Guide

    1



  • Page 4

    Contents

    C881G-U-K9 ISRs 1-60
    HSPA+ Versions of the Fixed-Platform ISRs 1-60
    Cisco C881, C886, and C887 Series ISRs 1-60
    Cisco C881 Router 1-61
    Cisco C886VA Router 1-62
    Cisco C886VAJ Router 1-63
    Cisco C887VA Router 1-64
    Cisco C887VAM Router 1-65
    Cisco C888 Integrated Services Router 1-67
    Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers
    Cisco C881G-4G Integrated Services Router 1-79
    Cisco C886VAG-LTE 1-82
    Cisco C887VAG-4G Integrated Services Router 1-85
    Cisco C896VAG-LTE Integrated Services Router 1-88
    Cisco C897VAG-LTE Integrated Service Router 1-92
    Cisco C898EAG-LTE Integrated Service Router 1-95
    Cisco C899G-LTE Integrated Service Router 1-99
    Cisco 890 Series Integrated Service Routers 1-104
    Cisco 891, Cisco 892, and Cisco 892F 1-104
    Cisco C897VAB-K9 1-114
    Cisco C891 Series ISRs 1-117
    Cisco C891F Router 1-117
    Cisco C891FW Router 1-119
    Cisco C891-24X/K9 Integrated Services Router 1-121
    Hardware Features 1-122
    Kensington Lock 1-123
    Reset Button 1-123
    LEDs 1-125
    Memory 1-131
    USB Port 1-132
    Fan 1-133
    Power Supply 1-133
    Power over Ethernet Module 1-133
    3G Cellular Data WAN Connectivity 1-134
    Small Form-Factor Pluggable Port 1-136
    Feature Summary 1-136
    Installing the Router

    2-1

    Installing the Cisco 810 ISR 2-1
    Installing the Cisco 812 ISR 2-1
    Cisco Integrated Services Router Hardware Installation Guide

    2

    1-70



  • Page 5

    Contents

    Items Shipped with your Router 2-2
    Items Shipped with your PoE+ Splitter 2-2
    Installing the Cisco PoE+ Splitter 2-2
    Grounding the Cisco 812 ISR 2-18
    Installing the Cisco 819 ISR 2-19
    Installing the Router 2-22
    Mounting the DC Power Supply 2-39
    Installing the Cisco 860, 880, 890 ISR 2-40
    Equipment, Tools, and Connections 2-41
    Items Shipped with your Router 2-41
    Additional Items 2-41
    Connections 2-42
    Ethernet Devices 2-42
    Installing the Cisco 860, 880, and 890 Series Routers 2-42
    Warnings 2-42
    Installing on a Table 2-43
    Mounting on a Wall 2-43
    Installing the Router Ground Connection 2-46
    Installing the FIPS Cover 2-46
    Installing Antennas for Cisco 890 Series 2-50
    Installing Cisco 890 Series in a Rack 2-54
    Installing the C881G-B/S/V-K9 ISR 2-56
    Installing Antennas 2-56
    Installing the C881GW-S/V-A-K9 ISR 2-56
    Installing Antennas 2-56
    Installing the C881G-U-K9 ISR 2-56
    Installing the Cisco 880G for 3.7G (HSPA+)/3.5G (HSPA) ISRs
    Connecting the Router

    2-58

    3-1

    Cisco 810 Series 3-1
    Cisco 819 Series 3-1
    Preparing to Connect the Router 3-1
    Connecting a PC, Server, or Workstation 3-2
    Connecting an External Ethernet Switch 3-3
    Connecting a Terminal or PC to the Console Port
    Connecting a Modem to the Console Port 3-5
    Connecting the AC Adapter 3-5
    Connecting the DC Adapter 3-6
    Verifying Connections 3-7
    Cisco 860, 880, 890 Series

    3-4

    3-8
    Cisco Integrated Services Router Hardware Installation Guide

    3



  • Page 6

    Contents

    Safety Warnings 3-9
    Preparing to Connect the Router 3-10
    Preventing Damage to the Router 3-11
    Connecting a PC, Server, or Workstation 3-12
    Connecting a Phone 3-13
    Connecting an External Ethernet Switch 3-14
    Connecting the V.92 modem Port 3-15
    Connecting a Terminal or PC to the Console Port 3-16
    Terminal Emulator Settings 3-16
    Connecting a Modem to the Auxiliary Port 3-17
    Connecting the 3G Card 3-18
    Installing the 3G Adapter for Extended Cable/Antenna 3-24
    Connecting a Data BRI Port 3-28
    Connecting an FE Line to an FE WAN Port 3-30
    Connecting a GE Line to an GE WAN Port 3-31
    Connecting an xDSL Line 3-31
    Connecting Power over Ethernet 3-34
    Connecting the AC Adapter 3-35
    Connecting an FXS Line 3-39
    Connecting an FXO Line 3-40
    Connecting a Voice ISDN BRI Line 3-42
    Verifying Connections 3-45
    Initial Configuration

    4-1

    Cisco 810 Series 4-1
    Cisco 819 Series 4-1
    Cisco IOS CLI 4-1
    Setup Command Facility 4-1
    Verifying the Initial Configuration

    4-2

    Cisco 860, 880, 890 Series 4-2
    Cisco Configuration Professional Express 4-2
    Cisco IOS CLI 4-2
    Setup Command Facility 4-4
    Verifying the Initial Configuration 4-6
    Initial Configuration of the Wireless Access Point
    Technical Specifications

    A-1

    Cisco 810 Series A-1
    Cisco 812 Series A-1
    Router Specifications

    A-1

    Cisco Integrated Services Router Hardware Installation Guide

    4

    4-7



  • Page 7

    Contents

    Mean Time Between Failure Ground Benign Environment
    Cisco 819 Series A-4
    Router Specifications A-4
    Mean Time Between Failure Ground Benign Environment
    Supported Power Adapters A-9

    A-4

    A-8

    Cisco 860, 880, 890 Series A-11
    Router Specifications A-12
    All Models Except Cisco 860VAE Series A-12
    Cisco 860VAE Series A-14
    Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series
    Cisco 870 Series A-16
    Cisco 880 Series A-17
    Cisco 880G Series 3G Wireless Integrated Services Router A-19
    Cisco 880VA Series A-19
    Cisco 890 Series A-21
    Power Supply A-22
    Wireless Access Point A-22
    FE and GE Port Pinouts A-23
    Console and Auxiliary Port Connector Pinouts A-24
    FXS and FXO Port Connector Pinouts A-24
    VDSL2 Port Connector Pinouts A-24
    ADSL2+ Port Connector Pinouts A-25
    V.92 Port Connector Pinouts A-25
    G.SHDSL Port Connector Pinouts A-25
    Data BRI Port Connector Pinouts A-26
    Voice ISDN BRI Interface Pin Numbers and Functions A-27
    SFP Port Connector Pinouts A-27
    Cable Specifications A-28
    Ethernet Cable Specifications A-28
    Maximum Cable Length A-28

    A-15

    Cisco Integrated Services Router Hardware Installation Guide

    5



  • Page 8

    Contents

    Cisco Integrated Services Router Hardware Installation Guide

    6



  • Page 9

    Preface
    This preface describes the objectives, audience, organization, and conventions of this guide and
    describes related documents that have additional information. It contains the following sections:


    Objective, page vii



    Audience, page vii



    Organization, page viii



    Conventions, page viii



    Related Documentation, page xvi



    Searching Cisco Documents, page xvi



    Obtaining Documentation and Submitting a Service Request, page xvii

    Objective
    This guide provides an overview and explains how to install, connect, and perform initial configuration
    for the following series:


    Cisco 810 series ISRs that include both Cisco 812 series and 819 series ISRs



    Wireless and non-wireless Cisco 860 series, Cisco 880 series, and Cisco 890 Integrated Services
    Routers (ISRs)

    Audience
    This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar
    with Cisco routers and Cisco IOS software and features.

    Cisco Integrated Services Router Hardware Installation Guide

    vii



  • Page 10

    Organization
    This guide is organized into the following chapters and appendix.
    Chapter

    Name

    Description

    Chapter 1

    Chapter 1, “Product Overview”

    Describes the router models and the
    hardware features available.

    Chapter 2

    Chapter 2, “Installing the Router”

    Lists the items shipped with the router, the
    equipment and tools necessary for
    installing the router, the safety warnings
    and guidelines, and the procedures for
    installing the router.

    Chapter 3

    Chapter 3, “Connecting the Router”

    Describes typical connections for the
    router, procedures for connecting the
    router to various devices, and how to
    verify the connections.

    Chapter 4

    Chapter 4, “Initial Configuration”

    Provides the procedures for initially
    configuring the router settings.

    Appendix A

    Appendix A, “Technical Specifications” Provides the router, port, and cabling
    specifications.

    Conventions
    This section describes the conventions used in this guide.

    Note

    Caution

    Tip

    Means reader take note. Notes contain helpful suggestions or references to additional information and
    material.

    This symbol means reader be careful. In this situation, you might do something that could result in
    equipment damage or loss of data.

    Means the following information will help you solve a problem. The tip information might not be
    troubleshooting or even an action, but could be useful information.

    Cisco Integrated Services Router Hardware Installation Guide

    viii



  • Page 11

    Warning

    IMPORTANT SAFETY INSTRUCTIONS
    This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
    work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
    with standard practices for preventing accidents. Use the statement number provided at the end of
    each warning to locate its translation in the translated safety warnings that accompanied this
    device. Statement 1071
    SAVE THESE INSTRUCTIONS

    Waarschuwing

    BELANGRIJKE VEILIGHEIDSINSTRUCTIES
    Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
    veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
    elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
    praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
    waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
    raadplegen.
    BEWAAR DEZE INSTRUCTIES

    Varoitus

    TÄRKEITÄ TURVALLISUUSOHJEITA
    Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
    käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
    onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
    mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
    lausuntonumeroiden avulla.
    SÄILYTÄ NÄMÄ OHJEET

    Attention

    IMPORTANTES INFORMATIONS DE SÉCURITÉ
    Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
    entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
    conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
    couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
    avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
    référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
    CONSERVEZ CES INFORMATIONS

    Warnung

    WICHTIGE SICHERHEITSHINWEISE
    Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
    kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
    den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
    Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
    Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
    BEWAHREN SIE DIESE HINWEISE GUT AUF.

    Cisco Integrated Services Router Hardware Installation Guide

    ix



  • Page 12

    Avvertenza

    IMPORTANTI ISTRUZIONI SULLA SICUREZZA
    Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
    persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
    relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
    Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
    traduzioni delle avvertenze riportate in questo documento.
    CONSERVARE QUESTE ISTRUZIONI

    Advarsel

    VIKTIGE SIKKERHETSINSTRUKSJONER
    Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
    begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
    elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
    av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
    enheten.
    TA VARE PÅ DISSE INSTRUKSJONENE

    Aviso

    INSTRUÇÕES IMPORTANTES DE SEGURANÇA
    Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
    lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
    perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
    prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
    localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
    GUARDE ESTAS INSTRUÇÕES

    ¡Advertencia!

    INSTRUCCIONES IMPORTANTES DE SEGURIDAD
    Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
    cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
    procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
    número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
    a este dispositivo.
    GUARDE ESTAS INSTRUCCIONES

    Varning!

    VIKTIGA SÄKERHETSANVISNINGAR
    Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
    Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
    känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
    varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
    anordning.
    SPARA DESSA ANVISNINGAR

    Cisco Integrated Services Router Hardware Installation Guide

    x



  • Page 13

    Cisco Integrated Services Router Hardware Installation Guide

    xi



  • Page 14

    Aviso

    INSTRUÇÕES IMPORTANTES DE SEGURANÇA
    Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
    corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
    circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
    número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
    segurança traduzidos que acompanham o dispositivo.
    GUARDE ESTAS INSTRUÇÕES

    Advarsel

    VIGTIGE SIKKERHEDSANVISNINGER
    Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
    legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
    involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
    undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
    oversatte advarsler, der fulgte med denne enhed.
    GEM DISSE ANVISNINGER

    Cisco Integrated Services Router Hardware Installation Guide

    xii



  • Page 15

    Cisco Integrated Services Router Hardware Installation Guide

    xiii



  • Page 16

    Warning

    When installing the product, please use the provided or designated connection cables/power
    cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical
    Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown
    on the code) for any other electrical devices than products designated by CISCO. The use of cables
    that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the
    code) is not limited to CISCO-designated products. Statement 371

    Warning

    Read the wall-mounting instructions carefully before beginning installation. Failure to use the
    correct hardware or to follow the correct procedures could result in a hazardous situation to people
    and damage to the system. Statement 378

    Warning

    There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
    the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
    to the manufacturer’s instructions. Statement 1015

    Warning

    To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
    voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
    LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021

    Warning

    This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
    absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
    authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

    Cisco Integrated Services Router Hardware Installation Guide

    xiv



  • Page 17

    Warning

    If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port
    to a public network that follows the European Union standards. Connecting the port to this type of
    public network can cause severe personal injury or can damage the unit. Statement 1031

    Warning

    Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV)
    requirements in IEC 60950 based safety standards. Statement 1033

    Warning

    Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
    tub, in a wet basement, or near a swimming pool. Statement 1035

    Warning

    Never install telephone jacks in wet locations unless the jack is specifically designed for wet
    locations. Statement 1036

    Warning

    Never touch uninsulated telephone wires or terminals unless the telephone line has been
    disconnected at the network interface. Statement 1037

    Warning

    Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
    risk of electric shock from lightning. Statement 1038

    Warning

    When installing or replacing the unit, the ground connection must always be made first and
    disconnected last. Statement 1046

    Warning

    Do not locate the antenna near overhead power lines or other electric light or power circuits, or
    where it can come into contact with such circuits. When installing the antenna, take extreme care
    not to come into contact with such circuits, because they may cause serious injury or death. For
    proper installation and grounding of the antenna, please refer to national and local codes (for
    example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code,
    Section 54). Statement 1052

    Warning

    No user-serviceable parts inside. Do not open. Statement 1073

    Warning

    Installation of the equipment must comply with local and national electrical codes. Statement 1074

    Warning

    Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
    Statement 1030

    Cisco Integrated Services Router Hardware Installation Guide

    xv



  • Page 18

    Warning

    Read the installation instructions before connecting the system to the power source. Statement 1004

    Warning

    Ultimate disposal of this product should be handled according to all national laws and regulations.
    Statement 1040

    Warning

    The covers are an integral part of the safety design of the product. Do not operate the unit without the
    covers installed. Statement 1077

    Warning

    Hot surface. Statement 1079

    Warning

    The equipment is suitable for installation in the following locations:
    Network Telecommunications Facilities
    Location where the NEC applies
    OSP

    Related Documentation


    Regulatory Compliance and Safety Information for Cisco 800 Series Routers



    Cisco IOS Software Releases 12.4 Special and Early Deployments



    Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T



    Cisco IOS Security Configuration Guide, Release 12.4T



    Cisco IOS Security Command Reference, Release 12.4T



    Cisco CP Express User’s Guide

    Searching Cisco Documents
    To search an HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most
    browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward
    is also available.
    To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader
    Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document.
    Use the Full Reader Search window to search multiple PDF files simultaneously and to change case
    sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF
    documents.

    Cisco Integrated Services Router Hardware Installation Guide

    xvi



  • Page 19

    Obtaining Documentation and Submitting a Service Request
    For information on obtaining documentation, submitting a service request, and gathering additional
    information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
    revised Cisco technical documentation, at:
    http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
    Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
    and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
    service and Cisco currently supports RSS Version 2.0.

    Cisco Integrated Services Router Hardware Installation Guide

    xvii



  • Page 20

    Cisco Integrated Services Router Hardware Installation Guide

    xviii



  • Page 21

    CH A P T E R

    1

    Product Overview
    This chapter provides an overview of the features available for the Cisco 812, Cisco 819, Cisco 860, 880,
    890 Integrated Services Router (ISR) and contains the following sections:

    Note



    Cisco 810 Series, page 1-1



    Cisco 860, 880, 890 Series, page 1-42

    For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco
    800 Series Routers.

    Cisco 810 Series
    This section contains the following:


    Cisco 812 Series, page 1-1



    Cisco 819 Series, page 1-10

    Cisco 812 Series
    This section provides an overview of the features available for the Cisco 812 Integrated Services Router
    (ISR) and contains the following sections:

    Note



    General Description, page 1-1



    Hardware Features, page 1-4



    SKU Information, page 1-9

    For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco
    800 Series and SOHO Series Routers.

    General Description
    The Cisco 812 ISR is a new router that looks like an Access Point with 3G, WLAN, and routing
    capabilities.

    Cisco Integrated Services Router Hardware Installation Guide

    1-1



  • Page 22

    Chapter 1

    Product Overview

    Cisco 810 Series

    The 3rd Generation (3G) is a generation of standards for mobile technology that facilitates growth,
    increased in bandwidth, and supports more diverse applications.
    The Cisco 812 ISR can be powered by an (included) external AC adapter or by a PoE+ capable Ethernet
    source using an optional Cisco PoE splitter C810-POE-SPL.
    A Wireless Local Area Network (WLAN) implements a flexible data communication system frequently
    augmenting rather than replacing a wired LAN within a building or campus. WLANs use radio frequency
    to transmit and receive data over the air, minimizing the need for wired connections. Figure 1-1 shows
    the Cisco 812 ISR.
    Cisco 812 ISR

    344399

    Figure 1-1

    Cisco Integrated Services Router Hardware Installation Guide

    1-2



  • Page 23

    Product Overview
    Cisco 810 Series

    Figure 1-2 shows the 3G antenna and LEDs display.
    Figure 1-2

    Cisco 812 ISR 3G and LEDs Display

    2

    1

    3

    4

    344400

    Chapter 1

    1

    3G diversity antenna

    3

    WiFi LED

    2

    3G main antenna

    4

    3G LED

    Cisco Integrated Services Router Hardware Installation Guide

    1-3



  • Page 24

    Chapter 1

    Product Overview

    Cisco 810 Series

    Figure 1-3 shows the I/O side of the Cisco 812 ISR.
    Figure 1-3

    Cisco 812 ISR I/O Side

    1

    2

    S

    3

    4

    GE WAN L

    DIV/GPS

    MAIN

    C812G
    5VDC

    1

    GE WAN port

    3

    Power connection port

    2

    Console/Aux port

    4

    Power switch

    4.0A

    344393

    CON/
    AUX

    Hardware Features
    The Cisco 812 ISR supports the following hardware features:

    Note



    Platform Features, page 1-4



    Antenna, page 1-5



    LEDs, page 1-5



    Memory, page 1-8



    Power Supply, page 1-8

    The WAAS Express feature is not supported. This feature will be supported for 3G and 4G interfaces
    with later IOS releases.

    Platform Features
    The Cisco 812 ISR has the following platform features:


    1x GE Enabled WAN (1000/100/10 Base T)



    2 TNC connectors for 3G main and diversity antenna (diversity antenna multiplexed with GPS)



    512 MB Compact Flash Memory



    512 MB DRAM



    AC Power Brick (100–264 V and max 0.5 A)



    Optional PoE+ (802.3at Class 4) Power Splitter



    Built-in Grounding

    Cisco Integrated Services Router Hardware Installation Guide

    1-4



  • Page 25

    Chapter 1

    Product Overview
    Cisco 810 Series



    Ceiling and Wall Mounting Option



    LED indicators for the platform

    Antenna
    The Cisco 812 ISR supports 3G external antenna and WiFi embedded antenna.
    3G External Antenna

    The Cisco 812 ISR provides two standard panel-mount TNC connectors to support 3G. The main antenna
    is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or an
    amplified GPS antenna. See Figure 1-2 for the location of the antennas.
    WiFi Embedded Antenna

    The Cisco 812 ISR supports Dual ports WiFi radios (802.11 a/b/g/n) with embedded 2x3 MIMO.
    For compliance and safety information, see the Regulatory Compliance and Safety Information for the
    Cisco 800 Series and SOHO Series Routers.

    LEDs
    The Cisco 812 ISR has two LEDs located on the top side of the router. The 3G LED is located on the
    lower right side with respect to the Cisco logo. 3G LED supports multiple functions and colors. The WiFi
    LED is located on lower left side with respect to the Cisco logo. Table 1-1 describes the 3G LED for the
    Cisco 812 ISR.
    Table 1-1

    Cisco 812 3G LED Descriptions

    ROMMON Mode
    3G LED

    LED Color

    Description

    System

    Yellow

    FPGA download is complete.

    Green (four blinks)

    ROMMON is running.

    Off

    No power.
    Incomplete FPGA download.

    IOS 3G Mode
    3G Service Type

    White

    MC8700—2G (GPRS/EDGE)
    MC5728—1xRTT

    Green

    MC8700—3G (UMTS)
    MC5728—EVDO Rev 0

    Light Blue

    MC8700—3.5G (HSPA)
    MC5728—EVDO Rev A

    Blue

    MC8700—3.7G (HSPA+)
    MC5728—N/A

    Off (solid)

    No service.

    Cisco Integrated Services Router Hardware Installation Guide

    1-5



  • Page 26

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-1

    Cisco 812 3G LED Descriptions (continued)

    ROMMON Mode
    3G LED
    RSSI

    1

    LED Color

    Description

    White, Green, Light Blue, or
    Blue (solid)

    Signal > –60 dBm

    White, Green, Light Blue, or
    Blue (three blinks and then a
    long pause)

    Signal <= –60 to 74 dBm

    Very strong signal
    Strong signal.

    White, Green, Light Blue, or
    Signal <= –75 to –89 dBm
    Blue (two blinks and then a long
    Fair signal.
    pause)
    White, Green, Light Blue, or
    Blue (one blink and then a long
    pause)

    Signal <= –90 to –109 dBm

    Off

    Signal <= –110 dBm

    Marginal signal.

    Unusable signal.
    Fault / Alarm

    Amber (solid)

    Fault detected.

    Red (four blinks)

    Temperature alert.

    Red (solid)

    Software failure.
    Power cycle.

    1. The LED colors of RSSI can be any of the four colors (White, Green, Light Blue, or Blue) listed under 3G service type.

    Cisco Integrated Services Router Hardware Installation Guide

    1-6



  • Page 27

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-2 describes the WiFi LED for the Cisco 812 ISR.
    Table 1-2

    Cisco 812 ISR WiFi LED Descriptions

    Message Type

    Color

    Description

    Boot loader status sequence Blinking Green

    DRAM memory test in progress.
    DRAM memory test is OK.
    Board initialization in progress.
    Initializing FLASH file system.
    Initializing Ethernet.
    Ethernet is OK.
    Starting Cisco IOS.
    Initialization successful.

    Association status

    Operating status

    Green

    Normal operating condition with no
    wireless client associated.

    Blue

    Normal operating condition with at least
    one wireless client associated.

    Blinking Blue

    Software upgrade in progress.

    Rapidly cycling through Access point location command invoked.
    Blue, Green, Red, and
    White
    Blinking Red

    Ethernet link not operational.

    Yellow

    Router is powered up.
    FPGA download is complete.

    Boot loader warnings

    Blinking Green

    LED blinks four times when ROMMON is
    up.

    Blinking Blue

    Configuration recovery in progress.
    (MODE button pushed for 2 to 3 seconds)

    Boot loader errors

    Red

    Ethernet failure.

    Blinking Green

    Image recovery in progress (MODE button
    released).

    Red

    DRAM memory test failure.

    Blinking Red and Blue

    FLASH file system failure.

    Blinking Red and Off

    Environment variable failure.
    Bad MAC address.
    Ethernet failure during image recovery.
    Boot environment failure.
    No Cisco image file.
    Boot failure.

    Cisco Integrated Services Router Hardware Installation Guide

    1-7



  • Page 28

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-2

    Cisco 812 ISR WiFi LED Descriptions (continued)

    Message Type

    Color

    Description

    Cisco IOS errors

    Red

    Software failure. Try to disconnect and
    reconnect the unit power.

    Cycling through Blue,
    Green, Red, and Off

    General warning.

    Memory
    The Cisco 812 ISR supports 512 MB DRAM and 512 MB compact flash memory. The Host router
    software runs on the first core. The second core runs the WLAN Access Point software.
    If WLAN is not supported in an SKU, all 512 MB DRAM memory is allocated to the first core. For the
    SKUs that support WLAN, 128 MB out of the 512 MB main memory is allocated to the second core.
    If WLAN is not supported in an SKU, all 512 MB DRAM compact flash memory is allocated to the first
    core. For the SKUs that support WLAN, 64 MB out of the 512 MB main memory is allocated to the
    second core.

    Power Supply
    The following are power adapters supported in the Cisco 812 ISR:


    AC Power Adapter, page 1-8



    PoE+ Splitter, page 1-8

    AC Power Adapter

    The default configuration is AC adapter that supports up to 4 A of 5 VDC current. The supported AC
    power adapter is PWR2-20W-AC that has a nominal input voltage of 100 to 240 VAC.
    PoE+ Splitter

    The Cisco PoE+ splitter (C810-POE-SPL) splits PoE+ into power and GE. It has connectors built into
    the power supply at both input and output so cables can be used at desired length as an option. Figure 1-4
    shows the I/O side of the PoE+ splitter.

    Cisco Integrated Services Router Hardware Installation Guide

    1-8



  • Page 29

    Chapter 1

    Product Overview
    Cisco 810 Series

    Figure 1-4

    PoE+ Splitter I/O Side

    OUTPUT

    1

    2

    3

    4

    5

    6

    345067

    OUTPUT

    5

    1

    Grounding location

    4

    PoE+ input

    2

    Power status LED

    5

    Openings for power cord latch to lock into
    enclosure

    3

    GE0 output

    6

    Input power connection

    SKU Information
    Table 1-3 lists the different SKUs available for the Cisco 812 ISR. The AP802-AGN-X-K9 (WLAN PID)
    is integrated as part of the router for the SKUs that support WLAN and is not orderable separately.
    Table 1-3

    Supported SKUs

    SKU ID

    WLAN PID

    Description

    C812G+7-K9



    C812 Secure Router Standalone Unit (non-US) 3.7G HSPA
    + Release 7 with SMS/GPS
    WLAN is not supported.

    C812G-CIFI+7-E-K9

    AP802-AGN-E-K9

    C812 Secure Router (non-US) 3.7G HSPA + Release 7 with
    SMS/GPS and Dual WiFi Radio with ETSI

    C812G-CIFI+7-N-K9

    AP802-AGN-N-K9

    C812 Secure Router (non-US) 3.7G HSPA + Release 7 with
    SMS/GPS and Dual WiFi Radio with ANZ

    C812G-CIFI-V-A-K9

    AP802-AGN-A-K9

    C812 Secure Router for Verizon EV-DO Rev A with
    SMS/GPS and Dual WiFi Radio with FCC

    C812G-CIFI-S-A-K9

    AP802-AGN-A-K9

    C812 Secure Router for Sprint EV-DO Rev A with
    SMS/GPS and Dual WiFi Radio with FCC

    Cisco Integrated Services Router Hardware Installation Guide

    1-9



  • Page 30

    Chapter 1

    Product Overview

    Cisco 810 Series

    Cisco 819 Series
    This section provides an overview of the features available for the Cisco 819 and Cisco 819H Integrated
    Services Routers (ISRs) and contains the following sections:


    General Description, page 1-10



    SKU Information, page 1-14



    Hardware Features, page 1-27

    Note

    Cisco 819 is used to refer to Cisco 819HG, Cisco 819G, Cisco 819H, Cisco 819GW, Cisco 819HGW,
    Cisco 819HWD, Cisco 819HG-4G, and Cisco 819G-4G ISRs unless specifically called out otherwise.

    Note

    This product is a Class 1 Outside Plant (OSP) as per Telcordia GR-3108.

    Note

    For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
    that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and
    SOHO Series Routers.

    General Description
    The Cisco 819 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2
    (ISR G2) Family designed in compact hardened and non-hardened form factors, is the smallest Cisco
    IOS Software router with support for integrated fourth-generation (4G LTE) and third-generation (3G)
    wireless WAN (mobile broadband backhaul). The Cisco 819GW now supports Dual 802.11 a/b/g/n
    radios WiFi. The Cisco 819 ISR machine-to-machine gateway provides a rapidly deployable, highly
    available, reliable, and secure solution into machine-to-machine applications for financial, telemetry,
    utility, retail, industrial automation, and transportation with comprehensive management capability.
    Transparently integrated into Cisco IOS Software as an enterprise-class feature, the Cisco 819 Hardened
    ISR provides highly secure data, voice, and video communications to stationary and mobile network
    nodes across wired and wireless links.
    Available in both non-hardened (Cisco 819G) and hardened (Cisco 819HG) versions, the Cisco 819
    supporting 4G LTE and 3G wireless WAN (WWAN) speeds offers a cost-effective, rapidly deployable,
    reliable, and secure primary or backup solution. With support for industrial-grade components, the
    hardened Cisco 819HG extends the ISR machine-to-machine gateway footprint and provides the
    flexibility for deployment in many different stationary and mobile environments where space, heat
    dissipation, exposure to extreme temperatures, harsher environments, and low power consumption are
    critical factors. For mobile applications, Mobile IP delivers transparent roaming across multiple wireless
    networks capable of covering wide geographic areas.
    The Cisco 819 ISR is a standard form factor with a commercial operating range. The 3G Cisco 819 ISRs
    support the 3G speeds (High-Speed PacketAccess Plus [HSPA+] enabling up to 4G speeds and Evolution
    Data Optimized [EVDO Rev A]). They are backward-compatible with High-Speed Packet Access
    (HSPA), Universal Mobile Telecommunications Service (UMTS), Enhanced Data Rates for Global
    Evolution (EDGE), General Packet Radio Service (GPRS), and EVDO Rev 0/1xRTT.

    Cisco Integrated Services Router Hardware Installation Guide

    1-10



  • Page 31

    Product Overview
    Cisco 810 Series

    The 4G LTE C819 supports the latest Third-Generation Partnership Project (3GPP) Release 8 LTE
    standards. The Cisco 4G multimode LTE WWAN C819 provides persistent and reliable LTE connectivity
    with fallback and transparent handoff to earlier technologies. The Cisco 819HG-4G and Cisco 819G-4G
    support multimode 4G LTE and have embedded Sierra Wireless multimode modem.
    The Cisco 819 ISR is a desktop form factor with built-in wall-mount features, floor mount, and DIN rail
    mount features in selected SKUs. These routers are powered by an external AC power or optional DC
    adapter. Figure 1-5 shows the Cisco 819HG ISR.
    The Cisco 819GW ISRs support WiFi radios with a higher memory density and a new barrel-type power
    connector. A Wireless Local Area Network (WLAN) implements a flexible data communication system
    frequently augmenting rather than replacing a wired LAN within a building or campus. WLANs use
    radio frequency to transmit and receive data over the air, minimizing the need for wired connections.
    Figure 1-6 shows the Cisco 819HGW ISR.
    The Cisco 819GW ISRs have the following additional features:


    Dual 802.11 a/b/g/n radios



    External WiFi antenna



    WLAN LED

    Figure 1-5

    Cisco 819HG Integrated Services Router

    283010

    Chapter 1

    Cisco Integrated Services Router Hardware Installation Guide

    1-11



  • Page 32

    Chapter 1

    Product Overview

    Cisco 810 Series

    Cisco 819HGW Integrated Services Router

    285479

    Figure 1-6

    Figure 1-7 shows the front panel details of the Cisco 819HG ISR.
    Figure 1-7

    Cisco 819HG ISR Front Panel

    8

    245547

    5

    1

    2

    3

    4

    7

    1

    3G main antenna

    7

    FE ports

    2

    LEDs

    8

    GE WAN port

    3

    Reset button

    9

    Console/Aux port

    Cisco Integrated Services Router Hardware Installation Guide

    1-12

    6

    9

    10

    11

    12



  • Page 33

    Product Overview
    Cisco 810 Series

    4

    3G mini-USB diagnostic port

    10 5 VDC molex power input

    5

    Diversity/GPS antenna

    11 Power switch

    6

    12-in-1 serial port

    12 Ground

    Figure 1-8 shows the front panel details of the Cisco 819HGW ISR.
    Figure 1-8

    Cisco 819HGW ISR Front Panel

    5

    8

    344077

    Chapter 1

    1

    2

    3

    4

    6

    7

    9

    10

    1

    3G main antenna

    7

    FE ports

    2

    LEDs

    8

    GE WAN port

    3

    Reset button

    9

    Console/Aux port

    4

    3G mini-USB diagnostic port

    10 5 VDC barrel-type power input

    5

    Diversity/GPS antenna

    11 Power switch

    6

    12-in-1 serial port

    12 Ground

    11

    12

    Cisco Integrated Services Router Hardware Installation Guide

    1-13



  • Page 34

    Chapter 1

    Product Overview

    Cisco 810 Series

    Figure 1-9 shows the front panel details of the Cisco 819 4G LTE ISR.
    Figure 1-9

    Cisco 819 4G LTE ISR Front Panel

    8

    12

    285447

    5

    1

    2

    3

    4

    6

    7

    9

    10 11

    1

    4G antenna connector—M0/MAIN

    8

    GE WAN port

    2

    LEDs

    9

    Console/Aux port

    3

    Reset button

    10 Power input

    4

    4G/3G port

    11 Power switch

    5

    4G antenna connector—M1/DIV

    12 Active GPS antenna connector

    6

    Serial port

    13 Ground

    7

    FE ports

    13

    SKU Information
    Table 1-4 lists the different 3G SKUs available for the Cisco 819HG and Cisco 819G ISRs. All SKUs
    support external antenna.

    Note

    WLAN is not supported.

    Table 1-4

    Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs

    SKU ID

    Description

    C819HG+7-K9

    Compact Hardened 3G IOS Router with Global HSPA + Release 7 based on
    MC8705

    C819HG-U-K9

    Compact Hardened 3G IOS Router with GLOBAL HSPA Release 6 based on
    MC8795V

    C819HG-V-K9

    Compact Hardened 3G IOS Router with Verizon EVDO Rev A based on
    MC5728V

    C819HG-S-K9

    Compact Hardened 3G IOS Router with Sprint EVDO Rev A based on
    MC5728V

    Cisco Integrated Services Router Hardware Installation Guide

    1-14



  • Page 35

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-4

    Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs (continued)

    SKU ID

    Description

    C819HG-B-K9

    Compact Hardened 3G IOS Router with Bharat generic EVDO Rev A based
    on MC5728V

    C819G+7-K9

    Compact Non-hardened 3G IOS Router with Global HSPA + Release 7 based
    on MC8705

    C819G-U-K9

    Compact Non-hardened 3G IOS Router with GLOBAL HSPA Release 6
    based on MC8795V

    C819G-V-K9

    Compact Non-hardened 3G IOS Router with Verizon EVDO Rev A based on
    MC5728V

    C819G-S-K9

    Compact Non-hardened 3G IOS Router with Sprint EVDO Rev A based on
    MC5728V

    C819G-B-K9

    Compact Non-hardened 3G IOS Router with Bharat generic EVDO Rev A
    based on MC5728V

    Cisco Integrated Services Router Hardware Installation Guide

    1-15



  • Page 36

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-5 lists the different SKUs available for the Cisco 819HGW, Cisco 819H, and Cisco 819HWD
    ISRs.
    Table 1-5

    Supported SKUs for Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs

    SKU ID

    WLAN ID

    WiFi External Antenna
    Support

    C819HGW+7-E-K9

    AP802H-AGN-E-K9

    Yes

    Cisco 819 Secure Hardened M2M
    GW (non-US) 3.7G HSPA + Release
    7 with SMS/GPS and Dual WiFi
    Radio with ETSI

    C819HGW+7-N-K9

    AP802H-AGN-N-K9

    Yes

    Cisco 819 Secure Hardened M2M
    GW (non-US) 3.7G HSPA + Release
    7 with SMS/GPS and Dual WiFi
    Radio with ANZ

    C819HGW+7-A-A-K9

    AP802H-AGN-A-K9

    Yes

    Cisco 819 Secure Hardened M2M
    GW (North America) 3.7G HSPA +
    Release 7 with SMS/GPS and Dual
    WiFi Radio with FCC for ATT

    C819HGW-V-A-K9

    AP802H-AGN-A-K9

    Yes

    Cisco 819 Secure Hardened Router
    for Verizon EV-DO Rev A with
    SMS/GPS and Dual WiFi Radio with
    FCC

    C819HGW-S-A-K9

    AP802H-AGN-A-K9

    Yes

    Cisco 819 Secure Hardened Router
    for Sprint EV-DO Rev A with
    SMS/GPS and Dual WiFi Radio with
    FCC

    C819H-K9





    Cisco 819 Secure Hardened Router
    with Serial

    Description

    WLAN and 3G are not supported
    C819HWD-E-K9

    AP802H-AGN-E-K9

    Yes

    Cisco 819 Secure Hardened Router
    and Dual WiFi Radio with ETSI
    3G is not supported

    C819HWD-A-K9

    AP802H-AGN-A-K9

    Yes

    Cisco 819 Secure Hardened Router
    and Dual WiFi Radio with FCC
    3G is not supported

    Cisco Integrated Services Router Hardware Installation Guide

    1-16



  • Page 37

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-6 lists the different 4G LTE SKUs available for the Cisco 819HG and Cisco 819G ISRs.
    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs

    SKU ID

    Mode

    Operating Regions Frequency Band

    Description

    C819HG-4G-V-K9

    LTE—DOrA

    North America

    Compact Hardened Cisco
    819 router with multi
    mode LTE feature
    dedicated to Verizon
    Wireless networks. This
    comes with a Sierra
    Wireless MC7750
    modem.

    700 MHz (band 13) or LTE
    800/1900 MHz for CDMA
    1xRTT, 1xEVDO Rev A

    C819G-4G-V-K9

    LTE—DOrA

    North America

    700 MHz (band 13) for LTE
    800/1900 MHz for CDMA
    1xRTT, 1xEVDO Rev A

    C819HG-4G-A-K9

    LTE—HSPA+/

    North America

    HSPA/UMTS/

    700 MHz (band 17)/AWS (band
    4)/2100MHz (band 1) for LTE
    800/850/1900/2100 MHz for
    UMTS/ HSPA+/HSPA

    EDGE/GPRS

    850/900/1800/1900 MHz for
    GSM/EDGE/GPRS
    C819G-4G-A-K9

    LTE—HSPA+/

    North America

    HSPA/UMTS/

    700 MHz(band 17)/AWS(band
    4)/2100MHz(band 1) for LTE
    800/850/1900/2100 MHz for
    UMTS/ HSPA+/HSPA

    EDGE/GPRS

    850/900/1800/1900 MHz for
    GSM/EDGE/GPRS
    C819HG-4G-G-K9

    LTE—HSPA+/
    HSPA/UMTS/
    EDGE/GPRS

    Global

    800 MHz (band 20)/900 MHz
    (band 8)/1800 MHz (band
    3)/2100 MHz (band 1)/2600
    MHz (band 7) for LTE
    900/2100 MHz for UMTS/
    HSPA+/HSPA

    Compact Non-hardened
    Cisco 819 router with
    multi mode LTE feature
    dedicated to Verizon
    Wireless networks. This
    comes with a Sierra
    Wireless MC7750
    modem.
    Compact Hardened Cisco
    819 router with multi
    mode LTE feature
    dedicated to AT&T
    Wireless networks. This
    comes with a Sierra
    Wireless MC7700
    modem.
    Compact Non-hardened
    Cisco 819 router with
    multi mode LTE feature
    dedicated to AT&T
    Wireless networks. This
    comes with a Sierra
    Wireless MC7700
    modem.
    Hardened Cisco 819
    router with multi-mode
    LTE feature for global
    wireless networks. This
    comes with a Sierra
    Wireless MC7710
    modem.

    900/1800/1900 MHz for
    GSM/EDGE/GPRS

    Cisco Integrated Services Router Hardware Installation Guide

    1-17



  • Page 38

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID

    Mode

    Operating Regions Frequency Band

    C819G-4G-GA-K9

    LTE—HSPA+/

    Global (Europe,
    LTE—800 MHz (band 20)/900
    Australia and New MHz (band 8)/1800 MHz (band
    Zealand)
    3)/2100 MHz (band 1)/2600
    MHz (band 7)

    HSPA/UMTS/
    EDGE/GPRS

    Description

    Non-hardened Cisco 819
    router with multi-mode
    LTE feature for global
    wireless networks. This
    comes with a Sierra
    3G—800 MHz (band 6)/850
    Wireless MC7304
    MHz (band 5)/900 MHz (band 8)
    modem.
    /1900 MHz (band 2) 2100 MHz
    (band 1) for UMTS/
    HSPA+/HSPA
    2G—850/900/1800/1900 MHz
    for GSM/EDGE/GPRS

    C819G-4G-NA-K9



    LTE



    HSPA+



    HSPA



    UMTS



    EDGE



    GPRS

    North America
    (AT&T,
    Bell-Canada,
    Roger, Telus, and
    other GSM/LTE
    operators in USA
    and Canada)

    LTE:


    AWS (band 4)



    700 MHz (band 5)



    850 MHz (band 17)



    1900 MHz (band 2)



    2600 MHz (band 7)

    UMTS, HSPA+, HSPA:


    1900 MHz (band 2)



    AWS (band 4)



    850 (band 5)

    GSM, EDGE, GPRS:

    Cisco Integrated Services Router Hardware Installation Guide

    1-18



    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Non-hardened Cisco 819
    router with multi-mode
    LTE feature for AT & T
    wireless networks. This
    comes with a Sierra
    Wireless MC7354 modem



  • Page 39

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID
    C819G-4G-ST-K9

    Mode


    LTE



    EVDO Rev-A



    1xRTT

    Operating Regions Frequency Band

    Description

    North America
    (Sprint)

    Non-hardened Cisco 819
    router with multi-mode
    LTE feature for Sprint
    wireless networks. This
    comes with a Sierra
    Wireless MC7350
    modem.

    LTE:


    AWS (band 4)



    700 MHz (band 13)



    PCS 1900 MHz (band 25)

    3G:


    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    2G:

    C819G-4G-VZ-K9



    LTE



    EVDO Rev-A



    1xRTT

    North America
    (Verizon)



    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    LTE:


    AWS (band 4)



    700 MHz (band 13)



    PCS 1900 MHz (band 25)

    3G:


    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    Non-hardened Cisco 819
    router with multi-mode
    LTE feature for Verizon
    wireless networks. This
    comes with a Sierra
    Wireless MC7350
    modem.

    2G:


    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    Cisco Integrated Services Router Hardware Installation Guide

    1-19



  • Page 40

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID

    Mode

    C819GW-LTE-MN
    A-AK9

    Operating Regions Frequency Band

    Description

    North America

    C819GW-LTE-MNA-AK
    9 is a dedicated
    Multimode LTE SKU for
    North American wireless
    networks and comes with
    a Sierra Wireless
    MC7354MNA modem.

    For LTE:



    LTE



    HSPA+



    700 MHz (Band 13)



    EVDO
    Revision A
    (DOrA)



    700 MHz (Band 17)



    800 MHz (Band 5)



    1900 MHz (Band 2)



    1900 MHz (Band 25)



    AWS 1700/2100 MHz
    (Band 4)



    CDMA



    EDGE/GPRS/G
    SM

    For HSPA+:


    850 MHz (Band 5)



    900 MHz (Band 8)



    1900 MHz (Band 2)



    2100 MHz (Band 1)



    AWS 1700/2100 MHz
    (Band 4)

    C819GW-LTE-MNA-AK
    9 is a non-hardened Cisco
    819 Series Router.
    For 3GPP compliance, the
    extended temperature
    range for this SKU is -15
    to 50C. For non-3GPP
    compliance, it is -15 to
    55C.

    Dual SIMs in this SKU
    provide high reliability
    and cellular multihoming
    For CDMA and EVDO Revision support for LTE and
    HSPA-based networks
    A:
    using the common FW
    • 800 MHz (Band Class 0)
    technology within the
    same region. Dual SIMs
    • 1900 MHz (Band Class 1)
    in the North American
    • 800 MHz (Band Class 10)
    SKUs provide switchover
    For EDGE/GPRS/GSM:
    with different FW
    technology.
    • 850 MHz
    Note
    This is a 4G+
    • 900 MHz
    WiFi SKU. This
    • 1800 MHz
    SKU supports all
    North American
    • 1900 MHz
    carriers like
    Verizon, ATT,
    Sprint, and
    Canada using
    MC7354MNA
    modems.

    Cisco Integrated Services Router Hardware Installation Guide

    1-20



  • Page 41

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID
    C819G-LTE-MNAK9

    Mode

    Operating Regions Frequency Band

    Description

    North America

    C819G-LTE-MNA-K9 is
    a dedicated Multimode
    LTE SKU for global
    wireless network and
    comes with a Sierra
    Wireless MC7354-MNA
    modem.

    LTE:



    LTE



    HSPA+



    850MHz(band 19)



    EDGE/GPRS/G
    SM



    1500MHz(band 21)



    2100MHz(band 1)



    CDMA



    EVDO

    3G(UMTS,HSPA+,HSPA):


    800MHz(band 6)



    850MHz(band 5)



    850MHz(band 19)



    2100MHz(band 1)

    2G(GSM,EDGE,GPRS):


    850MHz



    900MHz



    1800MHz



    1900MHz

    C819G-LTE-MNA-K9 is
    a non-hardened Cisco 819
    Series Router.
    For 3GPP compliance, the
    extended temperature
    range for this SKU is -15
    to 50C. For non-3GPP
    compliance, it is -15 to
    55C.
    Dual SIMs in this SKU
    provide high reliability
    and cellular multihoming
    support for LTE and
    HSPA-based networks
    using the common FW
    technology within the
    same region. Dual SIMs
    provide switchover with
    different FW technology.
    Note

    This SKU does
    not have a WiFi
    module.

    Cisco Integrated Services Router Hardware Installation Guide

    1-21



  • Page 42

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID

    Mode

    C819HG-LTE-MNA
    -K9

    Operating Regions Frequency Band

    Description

    North America

    C819HG-LTE-MNA-K9
    is a dedicated Multimode
    LTE SKU for North
    American wireless
    networks and comes with
    a Sierra Wireless
    MC7354-MNA modem.

    LTE:



    LTE



    HSPA+



    AWS (band 4)



    EDGE/GPRS/G
    SM



    850MHz(band 19)



    1500MHz(band 21)



    CDMA



    2100MHz(band 1)



    EVDO

    3G(UMTS,HSPA+,HSPA):


    800MHz(band 6)



    850MHz(band 5)



    850MHz(band 19)



    2100MHz(band 1)

    2G(GSM,EDGE,GPRS):


    850MHz



    900MHz



    1800MHz



    1900MHz

    C819G-LTE-MNA-K9 is
    a hardened Cisco 819
    Series Router.
    For 3GPP compliance, the
    extended temperature
    range for this SKU is -15
    to 50C. For non-3GPP
    compliance, it is -15 to
    55C.
    Dual SIMs in this SKU
    provide high reliability
    and cellular multihoming
    support for LTE and
    HSPA-based networks
    using the common FW
    technology within the
    same region. Dual SIMs
    provide switchover with
    different FW technology.
    Note

    Cisco Integrated Services Router Hardware Installation Guide

    1-22

    This SKU does
    not have a WiFi
    module.



  • Page 43

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID
    C819G-LTE-LA-K9

    Mode


    LTE



    HSPA+




    Operating Regions Frequency Band

    Description

    Latin
    America/APAC

    C819G-LTE-LA-K9 is a
    dedicated Multimode LTE
    SKU for Latin American
    wireless networks and
    comes with a Sierra
    Wireless MC7430
    modem.

    For FDD LTE:


    700 MHz (band 28)

    HSPA



    850 MHz (band 5)

    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:


    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)

    Cisco Integrated Services Router Hardware Installation Guide

    1-23



  • Page 44

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID

    Mode

    C819GW-LTE-LACK9



    LTE



    HSPA+




    Operating Regions Frequency Band

    Description

    Latin
    America/APAC

    C819G-LTE-LA-CK9 is a
    dedicated Multimode LTE
    SKU for Latin American/
    APAC wireless networks
    and comes with a Sierra
    Wireless MC7430
    modem.
    C819GW-LTE-LA-CK9
    comes with WiFi-C
    802.11n dual radio.

    For FDD LTE:


    700 MHz (band 28)

    HSPA



    850 MHz (band 5)

    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:

    Cisco Integrated Services Router Hardware Installation Guide

    1-24



    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)



  • Page 45

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID
    C819GW-LTE-LAQK9

    Mode


    LTE



    HSPA+




    Operating Regions Frequency Band

    Description

    Latin
    America/APAC

    C819GW-LTE-LA-QK9
    is a dedicated Multimode
    LTE SKU for Latin
    American / APAC
    wireless networks and
    comes with a Sierra
    Wireless MC7430
    modem.
    C819GW-LTE-LA-QK9
    comes with WiFi-Q
    802.11n dual radio.

    For FDD LTE:


    700 MHz (band 28)

    HSPA



    850 MHz (band 5)

    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:


    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)

    Cisco Integrated Services Router Hardware Installation Guide

    1-25



  • Page 46

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-6

    Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)

    SKU ID

    Mode

    C819GW-LTE-LANK9



    LTE



    HSPA+




    Operating Regions Frequency Band

    Description

    Latin America /
    APAC

    C819GW-LTE-LA-NK9
    is a dedicated Multimode
    LTE SKU for Latin
    American / APAC
    wireless networks and
    comes with a Sierra
    Wireless MC7430
    modem.
    C819GW-LTE-LA-NK9
    comes with WiFi-N
    802.11n dual radio.

    For FDD LTE:


    700 MHz (band 28)

    HSPA



    850 MHz (band 5)

    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:


    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)

    Re-branding of C8xx-B and EHWIC-3G-EVDO-B
    The C881G-B-K9, C819G-B-K9, and EHWIC-EVDO-B (Bharat) SKUs are introduced as an umbrella
    SKU to cover BSNL, Tata, and Reliance service providers in India.
    Software based mechanism is introduced to identify specific carrier.
    Carrier ID and name are displayed under "show cellular <unit> hardware".
    The software mechanism is backward compatible with other existing CDMA SKUs such as
    HWIC-3G-CDMA(-S,-V) and PCEX-3G-CDMA(-S,-V).
    Cisco IOS Requirement
    15.3(2)T, 15.3(3)M or later. New MIB objects for carrier ID and name will be introduced in later release.
    Sample CLI Output
    Router#show cellular 0/0/0 hardware
    Modem Firmware Version = p2813301
    Modem Firmware built = 06-24-10
    Hardware Version = MC5728V Rev 1.0

    Cisco Integrated Services Router Hardware Installation Guide

    1-26



  • Page 47

    Chapter 1

    Product Overview
    Cisco 810 Series

    Electronic Serial Number (ESN) = 0x60E62C87 [09615084679] Preferred Roaming List (PRL)
    Version = 10 PRI SKU ID = 535479 Carrier ID = 19 Carrier Name = Reliance Current Modem
    Temperature = 30 degrees Celsius Endpoint Port Map = 75
    Router#

    Router#show cellular 0/1/0 hardware
    Modem Firmware Version = p2813301
    Modem Firmware built = 06-24-10
    Hardware Version = MC5728V Rev 1.0
    Electronic Serial Number (ESN) = 0x60E62431 [09615082545] Preferred Roaming List (PRL)
    Version = 10 PRI SKU ID = 535479 Carrier ID = 29 Carrier Name = Tata Current Modem
    Temperature = 30 degrees Celsius Endpoint Port Map = 75
    Router#

    Hardware Features
    This section provides an overview of the following hardware features for the Cisco 819 ISR.

    Note



    Platform Features for Cisco 819 ISRs, page 1-27



    Antennas, page 1-29



    Power Switch, page 1-29



    Reset Button, page 1-30



    LEDs, page 1-30



    Memory, page 1-34



    Embedded 3G Modem, page 1-34



    Embedded 4G LTE Modem, page 1-34



    SIM Card, page 1-34



    Supported Cisco Antennas and Cables, page 1-35



    Serial Port, page 1-40



    Power Supply, page 1-41



    Accessories, page 1-42

    The WAAS Express feature is not supported. This feature will be supported for 3G and 4G interfaces
    with later IOS releases.

    Platform Features for Cisco 819 ISRs
    Table 1-7 lists the platform features comparison for the Cisco 819 ISRs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-27



  • Page 48

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-7

    Cisco 819 ISRs Platform Features

    Cisco 819HG
    Cisco 819G

    Cisco 819HGW
    Cisco 819HWD

    Cisco 819HG-4G
    Cisco 819G-4G

    Cisco 819GW

    Platform Features

    (with 3G)

    (with 3G and WiFi)

    (with 4G LTE)

    (with 4G LTE and WiFi)

    512 MB DRAM

    Yes







    1 GB DRAM



    Yes

    Yes

    Yes

    1 Gigabit Ethernet
    WAN port

    Yes

    Yes

    Yes

    Yes

    12-in-1 serial
    interface

    Yes

    Yes

    Yes

    Yes

    256 KB of NVRAM Yes
    storage

    Yes

    Yes

    Yes

    256 Compact Flash Yes
    support in IDE mode
    (internal)







    1 GB Compact Flash —
    support in IDE mode
    (internal)

    Yes

    Yes

    Yes

    Cisco EnergyWise

    Yes

    Yes



    Yes

    Dual 802.11 a/b/g/n
    Radios with Cisco
    DFS, CleanAir, and
    Client Link support



    Yes



    Yes

    Embedded 3G
    modem

    Yes

    Yes





    Embedded 4G LTE
    modem





    Yes

    Yes

    Environmental
    Yes
    monitoring and
    temperature logging

    Yes



    Yes

    Four ports FE
    interconnect switch
    support

    Yes

    Yes

    Yes

    Yes

    LED indicators for
    the platform

    Yes

    Yes

    Yes

    Yes

    Onboard crypto
    acceleration

    Yes

    Yes

    Yes

    Yes

    Power cord retention —
    lock

    Yes

    Yes

    Yes

    Power switch lock



    Yes

    Cisco 819HG-4G ISRs Yes
    only

    Reset button

    Yes

    Yes

    Yes

    Cisco Integrated Services Router Hardware Installation Guide

    1-28

    Yes



  • Page 49

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-7

    Cisco 819 ISRs Platform Features (continued)

    Cisco 819HG
    Cisco 819G

    Cisco 819HGW
    Cisco 819HWD

    Cisco 819HG-4G
    Cisco 819G-4G

    Cisco 819GW

    Platform Features

    (with 3G)

    (with 3G and WiFi)

    (with 4G LTE)

    (with 4G LTE and WiFi)

    Real Time Clock
    (RTC)1

    Yes

    Yes

    Yes

    Yes

    ScanSafe

    Yes

    Yes



    Yes

    Single console/AUX Yes
    port

    Yes

    Yes

    Yes

    SNMP

    Yes

    Yes



    Yes

    TFTP support with
    Ethernet WAN
    interface



    Yes



    Yes

    Warm reload

    Yes

    Yes



    Yes

    1. A real-time clock (RTC) with battery backup provides date and time when the system is powered on. The RTC is used to verify the validity of the
    Certification Authority stored on the router.

    Antennas
    The Cisco 819 3G routers provide two standard panel-mount TNC connectors to support the 3G antenna
    and the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The
    second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power
    supply from the router.
    The Cisco 819 4G routers provide two standard panel-mount TNC connectors on the router front panel
    for the main and diversity antennas. The main antenna connector is used for the primary 4G antenna. The
    second antenna connector can be used as a diversity receive only 4G antenna. An SMA connector for
    active GPS antenna is also available on the front panel of the router.
    The Cisco 819HGW and Cisco 819HWD ISRs also support Cisco WiFi external antennas. See the
    “Supported Cisco Antennas and Cables” section on page 1-35 for more information.
    WiFi External Antenna

    The external WiFi antenna is used to support better WiFi coverage. All external antenna supports the
    following:


    Dual 802.11 a/b/g/n radios



    2x3 MIMO



    Omnidirectional

    Power Switch
    The power switch shuts down the router. A power switch lock is available to prevent accidental turning
    off of the router in the hardened SKUs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-29



  • Page 50

    Chapter 1

    Product Overview

    Cisco 810 Series

    Reset Button
    The Reset button resets the router configuration to the default configuration set by the factory. To restore
    the router configuration to the default configuration set by the factory, use a standard size #1 paper clip
    with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power
    to the router.

    LEDs
    The LEDs are located on the front panel of the router. Table 1-8 describes the 3G LEDs for the Cisco
    819 ISR.
    Table 1-8

    3G LED Descriptions

    LED

    Color

    Description

    SYS

    Yellow

    FPGA download is complete.

    Green (blinking)

    ROMMON is operational.

    Green (solid)

    IOS is operational.

    Green (four blinks
    during bootup)

    Reset button has been pushed during the bootup.

    Off

    After powering up, when FPGA is being downloaded (in
    ROMMON).

    Green (blinking)

    Network activity on FE Switch ports, GE WAN port, 3G
    cellular interface, and serial interfaces.

    Off

    No network activity.

    Green

    Module is powered on and connected but not transmitting
    or receiving.

    Green (slow blinking)

    Module is powered on and searching for connection.

    Green (fast blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    Green (solid)

    Standalone GPS.

    Green (slow blinking)

    GPS is acquiring.

    Yellow (solid)

    Assisted GPS.

    Yellow (slow blinking)

    Assisted GPS is acquiring.

    Off

    GPS is not configured.

    ACT

    WWAN

    GPS

    Cisco Integrated Services Router Hardware Installation Guide

    1-30



  • Page 51

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-8

    3G LED Descriptions (continued)

    LED

    Color

    Description

    RSSI

    Green (solid)

    Signal > –60 dBm
    Very strong signal

    Green (three blinks and
    then a long pause)

    Signal <= –60 to 74 dBm

    Green (two blinks and
    then a long pause)

    Signal <= –75 to –89 dBm

    Green (one blink and
    then a long pause)

    Signal <= –90 to –109 dBm

    Off

    Signal <= –110 dBm

    Strong signal
    Fair signa
    Marginal signal
    Unusable signal

    SIM

    1,2

    Green / Yellow (one
    SIM in slot 0 active, SIM in slot 1 is not.
    green blink followed by
    two yellow blinks)
    Yellow / Green (one
    yellow blink followed
    by two green blinks)

    SIM in slot 1 active, SIM in slot 0 is not.

    Off / Green (two green No SIM in slot 0, SIM present in slot 1.
    blinks and then a pause)
    Green / Off (Slow single SIM present in slot0, no SIM in slot 1.
    green blink and then a
    pause
    3G

    Off / Off

    No SIM present in either slots.

    Green (one blink and
    then a pause)

    For 1xRTT, EGPRS, or GPRS service.

    Green (two blinks and
    then a pause)

    For EVDO, EVDO/1xRTT, or UMTS.

    Green (three blinks and
    then a pause)

    For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA.

    Green (solid)

    For HSPA PLUS.

    Off

    No Service.

    1. Not applicable to Verizon and Sprint EVDO modems.
    2. There is only one LED to indicate the status of two SIMs. A one-blink pattern represents the status of the SIM in slot 0,
    followed by a two-blink pattern for the SIM in slot 1.

    Table 1-9 describes the WLAN LEDs for the Cisco 819HGW and Cisco 819HWD ISRs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-31



  • Page 52

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-9

    WLAN LED Descriptions

    WLAN LED

    Color

    Description

    Boot loader status
    sequence

    Blinking Green

    Board initialization in progress.
    Initializing FLASH file system.
    Initializing Ethernet.
    Ethernet is OK.
    Starting Cisco IOS.
    Initialization is successful.

    Association status

    Operating status

    Boot loader errors

    Green

    Normal operating condition with no
    wireless client associated.

    Blue

    Normal operating condition with at least
    one wireless client associated.

    Blinking Blue

    Software upgrade in progress.

    Rapidly cycling through
    Green, Red, and White

    Access point location command invoked.

    Blinking Red

    Ethernet link is not operational.

    Blinking Red and Blue

    FLASH file system failure.

    Blinking Red and Off

    Environment variable failure.
    Bad MAC address.
    Ethernet failure during the image recovery.
    Boot environment failure.
    No Cisco image file.
    Boot failure.

    Cisco IOS errors

    Red

    Software failure. Try to disconnect and
    reconnect the unit power.

    Table 1-10 describes the 4G LTE LEDs for the Cisco 819 ISR.
    Table 1-10

    4G LTE LED Descriptions

    LED

    Color

    Description

    SYS

    Yellow

    FPGA download is complete.

    Green (blinking)

    ROMMON is operational.

    Green (solid)

    IOS is operational.

    Green (four blinks
    during bootup)

    Reset button has been pushed during the bootup.

    Off

    After powering up, when FPGA is being downloaded (in
    ROMMON).

    Cisco Integrated Services Router Hardware Installation Guide

    1-32



  • Page 53

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-10

    4G LTE LED Descriptions (continued)

    LED

    Color

    Description

    ACT

    Green (blinking)

    Network activity on FE Switch ports, GE WAN port, 3G
    cellular interface, and serial interfaces.

    Off

    No network connectivity.

    Green

    Module is powered on and connected but not
    transmitting or receiving.

    Green (slow blinking)

    Module is powered on and searching for connection.

    Green (fast blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    Green (solid)

    Standalone GPS.

    Green (slow blinking)

    GPS is acquiring.

    Yellow (solid)

    Assisted GPS.

    Yellow (slow blinking)

    Assisted GPS is acquiring.

    Off

    GPS is not configured.

    Green (solid)

    Signal > –60 dBm

    WWAN

    GPS

    RSSI

    Very strong signal
    Green (three blinks and
    then a long pause)

    Signal <= –60 to 74 dBm

    Green (two blinks and
    then a long pause)

    Signal <= –75 to –89 dBm

    Green (one blink and
    then a long pause)

    Signal <= –90 to –109 dBm

    Off

    Signal <= –110 dBm

    Strong signal
    Fair signal
    Marginal signal
    Unusable signal

    SIM

    Green / Yellow (one
    SIM in slot 0 is active, SIM in slot 1 is not.
    green blink followed by
    two yellow blinks)
    Yellow / Green (one
    yellow blink followed
    by two green blinks)

    SIM in slot 1 is active, SIM in slot 0 is not.

    Off / Green (two green No SIM in slot 0, SIM present in slot 1.
    blinks and then a pause)
    Green / Off (Slow single SIM present in slot 0, no SIM in slot 1.
    green blink and then a
    pause)
    Off / Off

    No SIM present in either slots.

    Cisco Integrated Services Router Hardware Installation Guide

    1-33



  • Page 54

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-10

    4G LTE LED Descriptions (continued)

    LED

    Color

    Description

    3G/4G

    Green (one blink and
    then a pause)

    For 1xRTT, EGPRS, or GPRS service.

    Green (two blinks and
    then a pause)

    For EVDO, EVDO/1xRTT, or UMTS service.

    Green (three blinks and
    then a pause)

    For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA
    service.

    Green (four blinks and
    then a pause)

    For HSPA+ service.

    Green (Solid)

    For 4G/LTE service.

    Off

    No Service.

    Memory
    The Cisco 819HG and Cisco 819G ISRs uses non-upgradable flash memory and main memory. The
    onboard flash memory contains the Cisco IOS software image and the boot flash contains the ROMMON
    boot code. Table 1-11 lists the memory requirements for Cisco 819 ISRs.
    Table 1-11

    Memory Requirements for Cisco 819 ISRs

    Cisco 819HG
    Cisco 819G

    Cisco 819HGW
    Cisco 819HWD

    Cisco 819HG-4G
    Cisco 819G-4G

    Memory Requirements

    (with 3G)

    (with WiFi)

    (with 4G LTE)

    256 Compact Flash support in
    IDE mode (internal)

    Yes





    1 GB Compact Flash support in
    IDE mode (internal)



    Yes

    Yes

    512 MB DRAM

    Yes





    1 GB DRAM



    Yes

    Yes

    Embedded 3G Modem
    The 3G cellular interface is the primary WAN data link, but it can also be used as a backup data link.
    The 3G technology is third-generation wide-area cellular technology that is used in broadband wireless
    data in a mobile environment.

    Embedded 4G LTE Modem
    The Cisco 819HG-4G and Cisco 819G-4G routers have an embedded 4G LTE modem provided by Sierra
    Wireless. The Verizon SKUs come with an MC7750 modem, the AT&T SKUs come with an MC7700
    modem, and the Global SKUs come with an MC7710 modem.

    SIM Card
    Table 1-12 lists the SIM Card slots available for Cisco the 819 ISRs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-34



  • Page 55

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-12

    SIM Card Slot

    Two Internal SIM Card Slots

    One Internal SIM Card Slot No SIM Card Slot

    C819G-U-K9

    C819HG-4G-V-K9

    C819HG-V-K9

    C819G+7-K9

    C819G-4G-V-K9

    C819HG-S-K9

    C819HG-U-K9

    C819HG-4G-A-K9

    C819G-V-K9

    C819HG+7-K9

    C819G-4G-A-K9

    C819G-S-K9

    C819HGW+7-A-A-K9

    C819G-4G-VZ-K9

    C819HGW-V-A-K9

    C819HGW+7-E-K9

    C819G-4G-ST-K9

    C819HGW-S-A-K9

    C819HGW+7-N-K9

    C819G-4G-NA-K9

    C819HG-B-K9

    C819HG-4G-G-K9

    C819G-B-K9

    C819G-4G-G-K9
    C819GW-LTE-MNA-AK9
    C819GW-LTE-GA-EK9
    C819G-LTE-LA-K9
    C819G-4G-GA-K9
    C819G-LTE-MNA-K9
    C819HG-LTE-MNA-K9
    C819GW-LTE-LA-CK9
    C819GW-LTE-LA-QK9
    C819GW-LTE-LA-NK9

    Supported Cisco Antennas and Cables
    The Cisco 819 ISR provides two standard panel-mount TNC connectors to support the 3G antenna and
    the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The
    second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power
    supply from the router.

    Note

    A Lightning Arrestor must be used when you install antenna outdoor. Note that the center conductor is
    not protected under 200V (sparkover voltage nominal value).

    Cisco Integrated Services Router Hardware Installation Guide

    1-35



  • Page 56

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-13 lists the Cisco 3G antennas that are supported for use on Cisco 819 ISRs.
    Table 1-13

    Supported Cisco 3G Antennas

    Cisco Part Number

    Antenna Type

    Maximum Gain and
    Frequency Range

    3G-ANTM1919D

    Dipole
    omnidirectional

    0 dBi
    (806–960 MHz)
    0 dBi
    (1710–2170 MHz)

    3G-ANTM1916-CM

    3G-AE015-R
    (Antenna Extension)

    Extension base

    0.8–6.0 GHz

    This antenna extension is a base with a 15-foot cable
    included for use with a dipole omnidirectional antenna.
    For more information, see Cisco Single-Port Antenna
    Stand for Multiband TNC Male-Terminated Portable
    Antenna (3G-AE015-R).

    +2 dBi
    800/900 MHz

    This is an outdoor low-profile omindirectional mast
    antenna. For more information, see Cisco 3G
    Omnidirectional Outdoor Antenna
    (3G-ANTM-OUT-OM).

    2.5 dBi
    (1710–2170 MHz)

    Low Profile Stick
    Antenna

    –1.5 dBi
    850, 900 MHz
    –2.5 dBi
    1800, 1900, 2100
    MHz

    Lightning Arrestor 800–2200 MHz

    .

    Cisco Integrated Services Router Hardware Installation Guide

    1-36

    Multiband ceiling-mounted omnidirectional antenna.
    For more information, see Cisco Multiband
    Omnidirectional Ceiling Mount Antenna
    (3G-ANTM1916-CM).

    1.5 dBi
    (806–960 MHz)

    +4 dBi
    1800/1900/2100
    MHz

    3G-ACC-OUT-LA
    (Lightning Arrestor)

    This is the default antenna with dual faceplate mount.
    Multiband faceplate-mounted dipole antenna. For more
    information, see Cisco Multiband Swivel Mount Dipole
    Antenna (3G-ANTM1919D).

    High-gain
    ceiling-mount
    omnidirectional

    3G-ANTM-OUT-OM Outdoor
    Omnidirectional

    3G-ANTM-OUT-LP

    Description

    This is an omindirectional stick antenna. For more
    information, see Cisco 3G Low Profile Outdoor Antenna
    (3G-ANTM-OUT-LP).

    This is a quarter-wave lightning protector with
    integrated high-pass filter. For more information, see
    Cisco 3G Lightning Arrestor (3G-ACC-OUT-LA).



  • Page 57

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-14 lists the supported Cisco WiFi antenna for Cisco 819HGW and Cisco 819HWD ISRs.
    Table 1-14

    Supported Cisco WiFi Antenna

    Antenna

    Frequency
    band(s)

    Mounting
    Mechanical

    AIR-ANTM2050D-R

    2.4–2.5 GHz Faceplate

    IP Rating

    Peak Gain
    Peak Gain
    2.4 GHz (dBi) 5 GHz (dBi) Description

    IP 41

    1.4

    4.5

    This is the default antenna. For
    more information, see Cisco
    Multiband Swivel-Mount
    Dipole Antenna
    (AIR-ANTM2050D-R).

    4.9–5.9 GHz Dipole

    AIR-ANT2430V-R

    2.4 GHz

    Ceiling

    IP 41

    3



    For more information, see
    Cisco Aironet 3-dBi
    Omnidirectional Antenna
    (AIR-ANT2430V-R).

    AIR-ANT5140V-R

    5 GHz

    Ceiling

    IP 41



    4

    For more information, see
    Cisco Aironet 4-dBi
    Omnidirectional Antenna
    (AIR-ANT5140V-R).

    AIR-ANT2440NV-R

    2.4 GHz

    Multi-mount IP 54
    (Wall/Ceiling
    /Mast)

    4



    For more information, see
    Cisco Aironet 2.4-GHz MIMO
    Wall-Mounted
    Omnidirectional Antenna
    (AIR-ANT2440NV-R).

    AIR-ANT5140NV-R

    5 GHz

    Multi-mount IP 54
    (Wall/Ceiling
    /Mast)



    4

    For more information, see
    Cisco Aironet 5-GHz MIMO
    Wall Mount Omnidirectional
    Antenna
    (AIR-ANT5140NV-R).

    Cisco Integrated Services Router Hardware Installation Guide

    1-37



  • Page 58

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-15 lists the Cisco 4G LTE antennas that are supported for use on Cisco 819 ISRs.
    Table 1-15

    Supported 4G LTE Antennas

    Cisco Part Number

    Description

    4G-LTE-ANTM-D

    Indoor 4G dipole
    omnidirectional antenna

    Maximum Gain and
    Frequency Ranges


    2 dBi
    – 698 to 806 MHz
    – 824 to 894 MHz

    Description
    Multiband dipole antenna. For more
    information, see Cisco 4G/3G
    Omnidirectional Dipole Antenna
    (4G-LTE-ANTM-D).

    – 925 to 960 MHz
    – 1710 to 1885 MHz
    – 1920 to 1980 MHz
    – 2110 to 2170 MHz
    – 2500 to 2690 MHz

    4G-ANTM-OM-CM

    Indoor ceiling-mount
    omnidirectional antenna

    ANT-4G-OMNI-OUT-N Multiband outdoor
    omnidirectional stick
    antenna

    698 to 2690 MHz



    1.5 dBi
    – 698 to 960 MHz



    3.5 dBi
    – 1710 to 2710 MHz

    Multiband omnidirectional
    ceiling-mount antenna. For more
    information, see Cisco 4G Indoor
    Ceiling-Mount Omnidirectional
    Antenna (4G-ANTM-OM-CM).
    Multiband outdoor omnidirectional
    stick antenna. For more information,
    see Cisco Outdoor Omnidirectional
    Antenna for 2G/3G/4G Cellular
    (ANT-4G-OMNI-OUT-N).

    – 2300 to 2700 MHz

    ANT-4G-SR-OUT-TNC Multiband outdoor
    omnidirectional saucer
    antenna



    1.5 dBi (peak gain with
    10-foot cable) or 0.8 dBi
    (peak gain with 15-foot
    cable)
    – 698 to 960 MHz



    Low-profile outdoor saucer antenna.
    For more information, see Cisco
    Integrated 4G Low-Profile Outdoor
    Saucer Antenna
    (ANT-4G-SR-OUT-TNC).

    3.7 dBi (peak gain with
    10-foot cable) or 0.2 dBi
    (peak gain with 15-foot
    cable)
    – 1710 to 2700 MHz

    CGR-LA-NF-NF

    Lighning Arrestor

    800 to 2200 MHz

    4G lightning arrestor kit for use on
    Cisco 4G wireless devices. For more
    information, see Lightning Arrestor for
    the Cisco 1240 Connected Grid Router.

    4G-ACC-OUT-LA

    Lightning Arrestor

    800 to 2200 MHz

    4G lightning arrestor kit for use on
    Cisco 4G wireless devices. For more
    information, see Cisco 4G Lightning
    Arrestor (4G-ACC-OUT-LA).

    Cisco Integrated Services Router Hardware Installation Guide

    1-38



  • Page 59

    Chapter 1

    Product Overview
    Cisco 810 Series

    Table 1-16 to Table 1-18 list the extension cables for use with 3G, WiFi, and 4G LTE antennas. The
    tables include the insertion loss information for the ultra-low-loss (ULL) LMR 400 extension cables.
    Table 1-16

    Cisco Extension Cables for Use with 3G Antennas

    Cisco Product Number

    Cable Length

    Insertion Loss

    Frequency (MHz)

    3G-CAB-ULL-20

    20 ft (6 m)

    1.50 dB max

    2100

    3G-CAB-ULL-50

    50 ft (15 m)

    3.50 dB max

    2100

    3G-CAB-LMR240-25

    25 ft (7.5 m)

    3.50 dB max

    2200

    3G-CAB-LMR240-50

    50 ft (15 m)

    6.90 dB max

    2200

    3G-CAB-LMR240-75

    75 ft (23 m)

    10.5 dB max

    2200

    Table 1-17

    Cisco Extension Cables for Use with WiFi Antennas

    Cisco Product Number

    Cable Length

    Insertion Loss

    Frequency (MHz)

    AIR-CAB005LL-R

    5 ft (1.524 m)

    0.5 dB

    2400

    (one RP-TNC plug, one
    RP-TNC jack)

    0.8 dB

    5800

    20 ft (6 m)

    1.3 dB

    2400

    (one RP-TNC plug, one
    RP-TNC jack)

    2.5 dB

    5800

    50 ft (15.24 m)

    3.4 dB

    2400

    (one RP-TNC plug, one
    RP-TNC jack)

    5.75 dB

    5800

    AIR-CAB020LL-R

    AIR-CAB050LL-R

    Table 1-18

    Cisco Extension Cables for Use with 4G LTE Antennas

    Cisco Product Number

    Cable Length

    Maximum Insertion
    Loss

    Frequency (MHz)

    Color

    Plenum Rated?1

    4G-AE010-R

    10 ft (3 m)

    1.4 dB at 700 MHz

    700 to 2600 MHz

    Black

    No

    700 to 2600 MHz

    Black

    No

    2.1 dB at 700 MHz

    700 to 1000 MHz

    Black

    Yes

    4.0 dB at 2.6 GHz

    1700 to 2600 MHz

    2.0 dB at 1.9 GHz
    2.1 dB at 2.1 GHz
    2.3 dB at 2.5 GHz
    4G-AE015-R

    15 ft (4.6 m)

    2.3 dB at 700 MHz
    3.3 dB at 1.9 GHz
    3.7 dB at 2.1 GHz
    4.0 dB at 2.5 GHz

    4G-CAB-LMR240-25

    25 ft (7.6 m)

    Cisco Integrated Services Router Hardware Installation Guide

    1-39



  • Page 60

    Chapter 1

    Product Overview

    Cisco 810 Series

    Table 1-18

    Cisco Extension Cables for Use with 4G LTE Antennas (continued)

    Cisco Product Number

    Cable Length

    Maximum Insertion
    Loss

    Frequency (MHz)

    Color

    Plenum Rated?1

    4G-CAB-LMR240-50

    50 ft (15 m)

    4.1 dB at 700 MHz

    700 to 1000 MHz

    Black

    Yes

    7.4 dB at 2.6 GHz

    1700 to 2600 MHz

    6.1 dB at 700 MHz

    700 to 1000 MHz

    Black

    Yes

    11.0 dB at 2.6 GHz

    1700 to 2600 MHz

    2.1 dB at 700 MHz

    700 to 1000 MHz

    Black

    No

    4.0 dB at 2600 MHz

    1700 to 2600 MHz

    4G-CAB-LMR240-75
    4G-CAB-LMR240-25N

    75 ft (23 m)
    25 ft (7.6 m)

    4G-CAB-ULL-20

    20 ft (6 m)

    1.8 dB

    700 to 2600 MHz

    Black

    Yes

    4G-CAB-ULL-50

    50 ft (15 m)

    4.2 dB

    700 to 2600 MHz

    Black

    Yes

    CAB-L400-20-TNC-N

    20 ft (6 m)

    1.75 dB

    700 to 2600 MHz

    Black

    No

    CAB-L400-50-TNC-N

    50 ft (15 m)

    4.0 dB

    700 to 2600 MHz

    Black

    No

    CAB-L400-20-N-N

    20 ft (6 m)

    2.75 dB

    700 to 2600 MHz

    Black

    No

    1. Cable can be routed within building plenum spaces.

    Serial Port
    The Cisco standard High Speed Smart Serial 12-in-1 connector allows the highest flexibility of
    connections to various DTE/DCE devices. The 12-in-1 serial interface pins connect to the FPGA. The
    FPGA configures the pin directions based on the cable type used. Figure 1-10 shows the magnified view
    of the 12-in-1 serial port. For more information, see About Serial Connections.

    Cisco Integrated Services Router Hardware Installation Guide

    1-40



  • Page 61

    Chapter 1

    Product Overview
    Cisco 810 Series

    12-in-1 Serial Port

    344749

    Figure 1-10

    Power Supply
    All SKUs require a 5 VDC power source. Cisco 819HG and Cisco 819G ISRs have a self-locking Molex
    mini-fit connector. Cisco 819HGW and Cisco 819HWD ISRs use a 5.5 mm barrel-type connector with
    separate locking clip. An external AC power adapter is supported by default. The optional external power
    adapters are available to support a variety of DC power sources, suitable for fixed, vehicle, or railway
    installations. The 5 VDC power input of the router is protected from over-voltage up to 20 VDC. The
    router will not power up if excessive voltage (for example, a 12 VDC adapter) is connected.
    AC Power Adapter

    The default configuration includes an external AC adapter that supplies up to 20 W of power. The AC
    power connection is a two-pin IEC 320 C8 receptacle. A mating AC power cord is supplied. The AC
    adapter does not provide chassis grounding to the router. A 1.3-meter long output cable connects to the
    router.
    DC Power Adapters

    The optional external DC power adapters are available for 12 VDC and 24 VDC nominal vehicle power.


    12 VDC vehicle adapter has a 10 VDC to 36 VDC operating range



    24 VDC vehicle adapter has an 18 VDC to 75 VDC operating range



    48 VDC vehicle adapter has an 20 VDC to 60 VDC operating range

    Cisco Integrated Services Router Hardware Installation Guide

    1-41



  • Page 62

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series



    The vehicle power adapters may be used for fixed or mobile installations. They do not provide electrical
    isolation; the input negative is connected to the output negative (chassis ground). Input cable is 350
    millimeter long with stripped and tinned bare wire connections. The input positive connection is a white
    wire and the input negative is a black wire.
    Railway Power Adapters

    The optional external power adapters meeting Railway Standards are available from a third-party
    supplier, Martek Power. Contact Martek Power directly to order and for detailed specifications. The use
    of Martek Power adapters listed in the “Supported Power Adapters” section on page A-9 will maintain
    Cisco warranty and support of the router; the power adapter itself is covered by Martek warranty. Input
    connection to the railway adapters is by a 350 millimeter long wire with stripped and tinned bare wire
    connection. A 1.3-meter long output cable connects to the router.

    Accessories
    Table 1-19 lists the accessories available for the Cisco 819 ISRs. For a complete list of SKUs that support
    these accessories, see the “Platform Features for Cisco 819 ISRs” section on page 1-27.
    Table 1-19

    Cisco 819 ISR Accessories

    Cisco Part Number

    Accessory

    69-2453-01

    Power cord retention lock

    69-2454-01

    Power switch lock cover

    Cisco 860, 880, 890 Series
    This section provides an overview of the features available for the Cisco 860 series, Cisco 880 series,
    and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections:

    Note



    General Description, page 1-43



    Cisco 860 Series ISRs, page 1-43



    Cisco 860VAE Series ISRs, page 1-45



    Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs,
    page 1-50



    Cisco 880 Series ISRs, page 1-53



    Cisco C881, C886, and C887 Series ISRs, page 1-66



    Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers, page 1-76



    Cisco 890 Series Integrated Service Routers, page 1-114



    Cisco C891 Series ISRs, page 1-127



    Hardware Features, page 1-132

    For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
    that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series.

    Cisco Integrated Services Router Hardware Installation Guide

    1-42



  • Page 63

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Note

    Some illustrations in this document show a wireless router. Both wireless and nonwireless models are
    available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations
    are similar for both wireless and nonwireless routers.

    Note

    Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers
    to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).

    General Description
    The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi
    CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup
    capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These
    routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers
    provide advanced features, such as high speed DSL (G.SHDSL, ADSL, or VDSL), 802.11n, quality of
    service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL). The Cisco 860VAE, 886VA
    and 887VA series routers have the additional capability of DSL Multi-mode (VDSL/ADSL).
    The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with
    built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These
    ISRs are powered by an external power supply adapter. The various models differ in the WAN interface
    and features that they support.

    Cisco 860 Series ISRs
    The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:


    An integrated 4-port 10/100 Ethernet switch for connecting to the LAN



    A10/100 Fast Ethernet (FE) port for connecting to the WAN.



    Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

    Cisco Integrated Services Router Hardware Installation Guide

    1-43



  • Page 64

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-7 shows the front panel details of the Cisco 860 wireless router.
    Front Panel of the Cisco 860 Series Wireless ISR

    231969

    Figure 1-11

    1

    1

    LEDs

    Figure 1-12 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do
    not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series
    routers.
    Figure 1-12

    Back Panel of the Cisco 861W ISR

    Cisco 861W

    232181

    WAN

    FE 4

    1

    3

    4

    5

    1

    Primary WAN port—10/100

    5

    Reset button

    2

    Antenna—captive omnidirectional dipole
    WLAN antenna (wireless models only)

    6

    Power connector

    3

    4-port 10/100 Ethernet switch

    7

    Earth ground connection

    4

    Serial port—console or auxiliary

    8

    Kensington security slot

    Cisco Integrated Services Router Hardware Installation Guide

    1-44

    2

    6

    7

    8



  • Page 65

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Cisco 860VAE Series ISRs
    The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features
    of the products in this series.

    Interfaces
    Table 1-20 describes the interfaces of the Cisco 860VAE series routers.
    Table 1-20

    Interfaces of the Cisco 860VAE Series ISRs

    Model
    Cisco
    866VAE

    Cisco
    867VAE

    Cisco
    866VAE-K9

    Cisco
    867VAE-K9

    x

    x

    x

    x

    1 GE switch port





    x

    x

    1 GE WAN port

    x

    x

    x

    x

    1 VDSL/ADSL over POTS port



    x



    x

    1 VDSL/ADSL over ISDN port

    x



    x



    Interfaces
    4 FE1 switch ports
    2

    1. FE = Fast Ethernet
    2. GE = Gigabit Ethernet

    Note

    The Cisco 866VAE, 867VAE, 866VAE-K9, and 867VAE-K9 routers each have two WAN ports. Only one
    of the two ports can be active at any given time.
    Table 1-21 describes the interfaces of the C860VAE series routers.
    Table 1-21

    Interfaces of the C860VAE Series ISRs

    Model
    Interfaces

    C867VAE

    C866VAE-K9

    C867VAE-K9

    1

    x

    x

    x

    2

    2 GE switch port

    x

    x

    x

    1 GE WAN port

    x

    x

    x

    1 VDSL/ADSL over POTS port

    x



    x

    1 VDSL/ADSL over ISDN port



    x



    3 FE switch ports

    1. FE = Fast Ethernet
    2. GE = Gigabit Ethernet

    Cisco Integrated Services Router Hardware Installation Guide

    1-45



  • Page 66

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    IOS Images
    Table 1-22 describes the IOS images included in Cisco 860VAE series routers.
    Table 1-22

    IOS Images of the Cisco 860VAE Series ISRs

    Model
    Cisco
    866VAE

    Cisco
    867VAE

    Cisco
    866VAE-K9

    Cisco
    867VAE-K9

    c860vae-ipbasek9-mz

    x

    x





    c860vae-advsecurityk9-mz





    x

    x

    c860vae-advsecurityk9_npe-mz





    x

    x

    IOS Image

    Table 1-23 describes the IOS images included in C860VAE series routers.
    Table 1-23

    IOS Images of the C860VAE Series ISRs

    Model
    IOS Image

    C867VAE

    C866VAE-K9

    C867VAE-K9

    c860vae-ipbasek9-mz

    x





    c860vae-advsecurityk9-mz



    x

    x

    c860vae-advsecurityk9_npe-mz



    x

    x

    Figure 1-13 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
    Cisco 867VAE-K9 integrated services routers (ISRs).
    Figure 1-13

    Front Panel of the Cisco 860VAE series ISR

    246199

    Cisco 860 Series

    1
    1

    LEDs

    Cisco Integrated Services Router Hardware Installation Guide

    1-46



  • Page 67

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-14 shows the front panel details of the C867VAE, C866VAE-K9, and C867VAE-K9 integrated
    services routers (ISRs).
    Figure 1-14

    Front Panel of the C860VAE series ISR

    246199

    Cisco 860 Series

    1
    1

    LEDs

    Figure 1-15 shows the back panel details of the Cisco 866VAE ISR.
    Figure 1-15

    Back Panel of the Cisco 866VAE ISR

    Cisco 866VAE
    VDSL/ADSL

    WAN

    OVER ISDN

    GE0

    1

    2

    LAN

    CONSOLE

    12V

    2.5A

    RESET
    FE 3

    FE 2

    FE 1

    3

    FE 0

    AUX

    4

    5

    246200

    Chapter 1

    6

    1

    xDSL port1

    6

    On/Off switch

    2

    GE WAN interface

    7

    Power connector

    3

    Ethernet LAN FE interfaces (FE0 through
    FE3 interfaces)

    8

    Reset button

    4

    USB port

    9

    Kensington security slot

    5

    Serial port—console or auxiliary

    7

    8

    9

    1. Using RJ-11.

    Cisco Integrated Services Router Hardware Installation Guide

    1-47



  • Page 68

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-16 shows the back panel details of the C867VAE ISR.
    Figure 1-16

    Back Panel of the C867VAE ISR

    Cisco 867VAE
    VDSL/ADSL

    WAN

    CONSOLE

    LAN

    12V

    2.5A

    1

    GE2

    GE1

    GE0

    FE2

    2

    FE1

    AUX

    FE0

    3

    385262

    RESET
    OVER POTS

    4

    5

    6

    1

    xDSL port1

    6

    On/Off switch

    2

    GE WAN interface

    7

    Power connector

    3

    Ethernet LAN GE and FE interfaces (GE0,
    GE1 interfaces and FE0 through FE2
    interfaces)

    8

    Reset button

    4

    USB port

    9

    Kensington security slot

    5

    Serial port—console or auxiliary

    7

    8

    9

    1. Using RJ-11.

    Figure 1-17 shows the back panel details of the Cisco 867VAE-K9.
    Figure 1-17

    Back Panel of the Cisco 867VAE-K9 ISR
    Cisco 867VAE-K9

    VDSL/ADSL

    WAN

    CONSOLE

    LAN

    12V

    2.5A

    RESET
    GE1

    1

    2

    GE0

    FE3

    FE1

    3

    AUX

    FE0

    4

    5

    6

    1

    xDSL port

    6

    On/Off switch

    2

    GE WAN interface

    7

    Power connector

    3

    Ethernet LAN GE and FE interfaces (GE0
    interface and FE0 through FE3 interfaces)

    8

    Reset button

    4

    USB port

    9

    Kensington security slot

    5

    Serial port—console or auxiliary

    Cisco Integrated Services Router Hardware Installation Guide

    1-48

    FE2

    284558

    OVER POTS

    7

    8

    9



  • Page 69

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-18 shows the back panel details of the C866VAE-K9.
    Figure 1-18

    Back Panel of the C866VAE-K9 ISR

    Cisco 866VAE-K9
    VDSL/ADSL

    WAN

    CONSOLE

    LAN

    12V

    2.5A

    1

    GE2

    GE1

    GE0

    2

    FE2

    FE1

    AUX

    FE0

    3

    385263

    RESET
    OVER ISDN

    4

    5

    6

    1

    xDSL port

    6

    On/Off switch

    2

    GE WAN interface

    7

    Power connector

    3

    Ethernet LAN GE and FE interfaces (GE0,
    GE1 interfaces and FE0 through FE2
    interfaces)

    8

    Reset button

    4

    USB port

    9

    Kensington security slot

    5

    Serial port—console or auxiliary

    7

    8

    9

    Figure 1-19 shows the back panel details of the C867VAE-K9.
    Figure 1-19

    Back Panel of the C867VAE-K9 ISR

    Cisco 867VAE-K9
    VDSL/ADSL

    WAN

    CONSOLE

    LAN

    12V

    2.5A

    RESET
    OVER POTS

    1

    GE2

    GE1

    GE0

    2

    FE2

    FE1

    AUX

    FE0

    3

    385261

    Chapter 1

    4

    5

    6

    1

    xDSL port

    6

    On/Off switch

    2

    GE WAN interface

    7

    Power connector

    3

    Ethernet LAN GE and FE interfaces (GE0,
    GE1 interfaces and FE0 through FE2
    interfaces)

    8

    Reset button

    4

    USB port

    9

    Kensington security slot

    5

    Serial port—console or auxiliary

    7

    8

    9

    Cisco Integrated Services Router Hardware Installation Guide

    1-49



  • Page 70

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and
    Cisco 860VAE-POE-W-A-K9 ISRs
    This section provides a hardware overview of the following Cisco 860VAE Series Integrated Services
    Routers (ISRs):


    C866VAE-W-E-K9



    C867VAE-W-A-K9



    C867VAE-W-E-K9



    C867VAE-POE-W-A-K9

    Model-Specific Features
    Table 1-24 describes the features specific to each of these router models:
    Table 1-24

    Model-Specific Router Features

    C866VAE-W-EK9

    C867VAE-W-AK9

    C867VAE-W-EK9

    C867VAE-POEW-A-K9

    WAN interface and mode

    One GE port,
    DSL over
    ISDN,
    Europe WiFi

    One GE port,
    DSL over
    POTS,
    America WiFi

    One GE port,
    DSL over
    POTS,
    Europe WiFi

    One GE port,
    DSL over
    POTS,
    America WiFi

    Power-over-Ethernet (PoE)

    No

    No

    No

    Yes

    Feature

    Common Features
    The following key features are common to each of these router models:


    Dual WAN interface (Gigabit Ethernet [GE] and dual-mode ADSL2+ /VDSL2)



    2.4 GHz wireless LAN (WLAN) interface



    Five Layer 2 LAN switches: two Gigabit Ethernet and three Fast Ethernet



    One USB 2.0 port in high-speed host mode



    One RJ-45 console port (RS-232 interface)



    Support for up to 512 MB DRAM using DDR in 16-bit mode



    Support for 8 MB Serial Peripheral Interface Bus (SPI) flash memory for boot and 128 MB NAND
    flash memory for storing IOS



    Reset/Recovery switch



    Silent convection cooling—no fan

    External Interfaces
    Figure 1-20 shows the back I/O panel of the Cisco 867VAE-POE-W-A-K9 series router.

    Cisco Integrated Services Router Hardware Installation Guide

    1-50



  • Page 71

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-20

    Back I/O Panel
    Cisco 867VAE-POE-W-A-K9
    VDSL/ADSL

    WAN

    LAN

    CONSOLE
    12V

    2.5A

    RESET
    GE2

    GE1

    GE0

    FE2

    FE1

    AUX

    FE0(POE)

    360426

    OVER POTS

    Table 1-25 describes the external interfaces included with these router models.
    Table 1-25

    External Interfaces

    Interface
    FE LAN port

    GE LAN port

    Connector
    RJ-45

    RJ-45

    Port
    Label

    Quantity Port
    3

    2

    FE LAN PORT 0

    FE01

    FE LAN PORT 1

    FE1

    FE LAN PORT 2

    FE2

    GE LAN PORT 0

    GE0

    GE LAN PORT 1

    GE1

    GE WAN port (10/100/1000 Base-T)

    RJ-45

    1

    GE WAN PORT

    GE2

    ADSL2+/VDSL2 WAN port

    RJ-11

    1





    USB 2.0

    1





    RJ-45

    1





    Host USB port
    Console port

    1. Provides Power-over-Ethernet (PoE) for the Cisco C867VAE-POE-W-A-K9.

    Note

    For the Cisco C867VAE-POE-W-A-K9, Power-over-Ethernet (PoE) is available using port FE0, with a
    60-W power supply.

    USB Interface
    The USB 2.0 interface enables:


    Transferring data using a USB flash token (USB memory stick) for system recovery and other tasks.



    Cisco IOS software boot from USB.

    Use only the following Cisco USB 2.0 flash tokens:

    Note



    MEMUSB-128FT (128 MB)



    MEMUSB-256FT (256 MB)



    MEMUSB-1024FT (1 GB)

    The USB 2.0 port cannot be used for connecting external devices or as a console for devices other than
    those specified in the USB eToken Device and USB Flash Features Support Data Sheet, available at:
    http://www.cisco.com/en/US/prod/collateral/modules/ps6247/product_data_sheet0900aecd80232473.h
    tml

    Cisco Integrated Services Router Hardware Installation Guide

    1-51



  • Page 72

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    LED Indicators
    These router models include LED indicators on the back panel for each LAN port, and additional LED
    indicators on the front panel of the unit.
    LED Indicators for LAN Ports

    On the back panel of the unit, each LAN port includes an LED indicator. Table 1-26 describes the LED
    indicators.
    Table 1-26

    Port

    Back Panel LED Indicators for LAN Ports

    LED Color

    Description

    Green

    Off—No link.

    FE Ports

    FE LAN 0

    Faster flashing indicates heavier traffic.
    FE LAN 1

    Green

    Off—No link.
    Faster flashing indicates heavier traffic.

    FE LAN 2

    Green

    Off—No link.
    Faster flashing indicates heavier traffic.

    GE Ports

    GE LAN 0

    Green

    Off—No link.
    Faster flashing indicates heavier traffic.

    GE LAN 1

    Green

    Off—No link.
    Faster flashing indicates heavier traffic.

    LED Indicators on Front Panel

    The front panel includes several LED indicators. Figure 1-21 shows the location of the LED indicators.
    Figure 1-21

    Front Panel LED Indicators

    Cisco 860 Series

    346497

    WLAN

    1
    1

    LED indicators

    Cisco Integrated Services Router Hardware Installation Guide

    1-52



  • Page 73

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-27 describes the LED indicators.
    Table 1-27

    Front Panel LED Indicators

    LED

    LED Color

    LED Activity

    Description

    Left Side

    DSL ACT

    Green

    Flashing

    Off



    DSL WAN activity. Faster flashing indicates heavier
    traffic.
    Device is powered off.
    or
    No DSL WAN activity.

    DSL LINK

    Green

    Off

    Solid

    DSL WAN mode is selected and DSL training is complete.

    Flashing

    DSL WAN mode is selected but DSL LinkUp state is
    incomplete, such as in-training (slow initially, fast when
    almost connected).



    Device is powered off.
    or
    GE WAN mode is selected.

    GE ACT

    Green

    Flashing

    Off



    GE WAN activity (traffic in either direction). Faster
    flashing indicates heavier traffic.
    Device is powered off.
    or
    No GE WAN activity.
    or
    No link.

    GE MODE

    Green

    Solid

    Off



    GE WAN mode is selected.
    Device is powered off.
    or
    DSL WAN mode is selected.

    Right Side

    WLAN

    Green

    Solid
    Flashing

    Off



    WLAN enabled.
    Indicates WLAN activity (traffic in either direction).
    Device is powered off.
    or
    WLAN is disabled.

    Power

    Green

    Solid

    Off



    On—The device is powered on.
    Device is powered off.

    Cisco 880 Series ISRs
    The Cisco 880 series ISRs have data and voice capabilities. They have the following features:

    Cisco Integrated Services Router Hardware Installation Guide

    1-53



  • Page 74

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series



    Integrated 4-port 10/100 Ethernet switch for connecting to the LAN



    10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode
    (VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for
    connecting to the WAN



    Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP



    Optional 2-port Power over Ethernet (PoE)

    Note



    The Cisco 880 series ISRs can include an optional PoE module that provides power to
    802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not
    configured with the factory order, you must order and install it to enable the PoE function.

    DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
    system memory

    The following features are located on the front panel:


    USB 1.1 port



    Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the
    Cisco 880G models

    This section contains the following topics:


    Cisco 880 Series Data Routers, page 1-54



    Cisco 880 Series Voice and Data Routers, page 1-57



    Cisco 880 Series with Embedded WLAN Antennas, page 1-63



    C881G-B/S/V-K9 ISRs, page 1-65



    C881GW-S/V-A-K9 ISRs, page 1-65



    C881G-U-K9 ISRs, page 1-66



    HSPA+ Versions of the Fixed-Platform ISRs, page 1-66

    Cisco 880 Series Data Routers
    The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,
    802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-22 through Figure 1-25 show
    the features available on Cisco 880 series data routers. Some of the features shown may not be available
    on your router.
    Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL
    over ISDN, VDSL/ADSL over POTS, or 10/100 FE. See the Cisco 880 Series Integrated Services
    Routers data sheet for the WAN interface that is supported on your router.
    Figure 1-22 shows the front panel details of the Cisco 880 wireless data router. The USB port and the
    3G card slot are located on the front panel.

    Cisco Integrated Services Router Hardware Installation Guide

    1-54



  • Page 75

    Product Overview
    Cisco 860, 880, 890 Series

    Front Panel of the Cisco 880 Series Wireless Data Router

    231950

    Figure 1-22

    1

    1
    2

    2

    3

    LEDs
    3G express card slot—Supports third-party
    3G card (Cisco 880G models only)

    3

    USB port

    1

    1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.

    Figure 1-23 shows the back panel details of the Cisco 886VA data router.
    Figure 1-23

    Back Panel of the Cisco 886VA Router

    254090

    Chapter 1

    1

    2

    3

    4

    5

    6

    1

    Data BRI1 0

    6

    Reset button

    2

    Primary WAN port—VDSL/ADSL over
    ISDN

    7

    Power connector

    3

    4-port 10/100 Ethernet switch2

    8

    Earth ground connection

    4

    Serial port—console or auxiliary

    9

    Kensington security slot

    5

    PoE power connector—optional

    7

    8

    9

    1. BRI = Basic rate interface.
    2. Ports 0 and 1 provide PoE with the optional PoE module installed.

    The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may
    occur if a non-RJ-45 connector is inserted.

    Cisco Integrated Services Router Hardware Installation Guide

    1-55



  • Page 76

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-24 shows the back panel details of the Cisco 887VA and 886VA-M data router.
    Back Panel of the Cisco 887VA and 887VA-M Router

    254139

    Figure 1-24

    1

    2

    3

    4

    5

    1

    Primary WAN port—VDSL/ADSL over
    POTS1

    5

    Reset button

    2

    4-port 10/100 Ethernet switch2

    6

    Power connector

    3

    Serial port—console or auxiliary

    7

    Earth ground connection

    4

    PoE power connector—optional

    8

    Kensington security slot

    6

    7

    8

    1. 887VA-M has Annex M support.
    2. Ports 0 and 1 provide PoE with the optional PoE module installed.

    For the Cisco 887VA, the primary WAN port is designed for an RJ-11 connector only. Damage to the
    primary WAN port may occur if a non-RJ-11 connector is inserted.

    Figure 1-25 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have
    antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data
    routers.
    Back Panel of the Cisco 888W Data Router

    231951

    Figure 1-25

    1

    2

    Cisco Integrated Services Router Hardware Installation Guide

    1-56

    3

    4

    5

    6

    7

    8

    9

    10



  • Page 77

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    1

    ISDN port—not available on 3G models

    6

    PoE power connector for optional PoE
    module1

    2

    Primary WAN port2—G.SHDSL,
    VDSLoPOTS, ADSLoPOTS, ADSLoISDN,
    or 10/100 FE

    7

    Reset button

    3

    Antenna—captive omnidirectional dipole
    WLAN antenna (wireless models only)

    8

    Power connector

    4

    4-port 10/100 Ethernet switch

    9

    Earth ground connection

    5

    Serial port—console or auxiliary

    10 Kensington security slot

    1. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
    to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the
    PoE function.
    2. Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, or 10/100 FE. The VDSLoPOTS
    port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See
    Figure 1-12 for the location of the 10/100 FE WAN port.

    Cisco 880 Series Voice and Data Routers
    The Cisco 880 series voice and data routers provide both voice and data ports. The voice ports managed
    voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or
    BRI connections.

    Cisco 881 SRST and Cisco 888 SRST
    Figure 1-26, Figure 1-27, and Figure 1-28 show the features available on the Cisco 881 SRST and
    Cisco 888 SRST routers. The features available vary, depending on the router model. Some features may
    not be available on your router.
    Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the
    Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are
    supported on your router.

    Cisco Integrated Services Router Hardware Installation Guide

    1-57



  • Page 78

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-26 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice
    router.
    Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router

    270495

    Figure 1-26

    1

    1

    LEDs

    Cisco Integrated Services Router Hardware Installation Guide

    1-58

    2

    2

    USB port



  • Page 79

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-27 shows the back panel details of the Cisco 881SRST-W voice router.
    Figure 1-27

    Back Panel of the Cisco C881SRST-W Voice Router

    241904

    Chapter 1

    6

    1

    2

    2

    3

    4

    5

    7

    8

    9

    10

    1

    Primary WAN port1—10/100 FE

    6

    Antenna—captive wireless omnidirectional
    dipole WLAN antenna (wireless models only)

    2

    Voice ports—four FXS2/DID3 ports, one
    FXO4 port with TBP5 power failover

    7

    Reset button

    3

    4-port 10/100 Ethernet switch6

    8

    Power connector

    4

    Serial port—console or auxiliary

    9

    Earth ground connection

    5

    PoE power connector for optional PoE
    module7

    10 Kensington security slot

    1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
    2. FXS = Foreign Exchange Station.
    3. DID = Direct Inward Dialing.
    4. FXO = Foreign Exchange Office.
    5. TBP = trunk bypass.
    6. Ports 0 and 1 provide PoE with the optional PoE module installed.
    7. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
    to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install the Field
    Replaceable Unit (FRU) to enable the PoE function. For this you either need the FRU “800-IL-PM=2” or “800G2-POE-2”.
    If your device has a separate PoE inlet, use the 800-IL-PM=2, if it has one combined inlet (a description saying “POE
    OPTION REQUIRES 5A POWER ADAPTOR”), then use the 800G2-POE-2.

    Cisco Integrated Services Router Hardware Installation Guide

    1-59



  • Page 80

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-28 shows the back panel details of the Cisco 888SRST-W voice router.
    Back Panel of the Cisco C888SRST-W Voice Router

    241905

    Figure 1-28

    2

    1

    2

    6

    3

    4

    5

    7

    8

    9

    10

    1

    Primary WAN port1—G.SHDSL

    6

    Antenna—captive wireless omnidirectional
    dipole WLAN antenna (wireless models only)

    2

    Voice ports—four FXS/DIDports and one
    voice BRI port

    7

    Reset button

    3

    4-port 10/100 Ethernet switch2

    8

    Power connector

    4

    Serial port—console or auxiliary

    9

    Earth ground connection

    5

    PoE power connector for optional PoE
    module3

    10 Kensington security slot

    1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
    2. Ports 0 and 1 provide PoE with the optional PoE module installed.
    3. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
    to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install the Field
    Replaceable Unit (FRU) to enable the PoE function. For this you either need the FRU “800-IL-PM=2” or “800G2-POE-2”.
    If your device has a separate PoE inlet, use the 800-IL-PM=2, if it has one combined inlet (a description saying “POE
    OPTION REQUIRES 5A POWER ADAPTOR”), then use the 800G2-POE-2.

    The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage to the
    primary WAN port may occur if a non-RJ-45 connector is inserted.

    Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W
    Figure 1-29, Figure 1-30, and Figure 1-31 show the features available on the Cisco 881-V and
    Cisco 887VA-V routers. The features available vary, depending on the router model. Some features may
    not be available on your router.
    The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS
    or BRI voice ports. However, the number of concurrent calls that can be supported by the router is limited
    by the codec complexity setting on the router. Table 1-28 lists the maximum number of calls that is
    supported when the codec complexity command is configured for Flexible, Medium or High complexity.

    Cisco Integrated Services Router Hardware Installation Guide

    1-60



  • Page 81

    Product Overview
    Cisco 860, 880, 890 Series

    Note

    Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect
    the maximum number of supported calls.
    Table 1-28

    Maximum Number of Supported Calls

    Flexible Complexity

    Medium Complexity

    High Complexity

    C881-V

    9

    8

    6

    C887VA-V

    8

    8

    6

    C887VA-V-W

    8

    8

    6

    Figure 1-29 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.

    Figure 1-29

    Front Panel of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Routers

    246861

    Chapter 1

    1

    1

    LEDs

    2

    2

    USB port

    Cisco Integrated Services Router Hardware Installation Guide

    1-61



  • Page 82

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-30 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless)
    router does not have the antennas on the back panel.
    Figure 1-30

    Back Panel of the Cisco 887 VA-V Router

    11
    VDSL/ADSL

    1

    5

    2

    246864

    overPOTS

    6

    C887VA-W VOICE

    3

    4

    4

    3

    5

    6

    7

    8

    9

    10

    1

    Data BRI

    7

    Reset Button

    2

    Voice BRI

    8

    Power connector

    3

    Voice ports—four FXS/DID ports

    9

    Earth ground connection

    4

    Fast Ethernet LAN—four ports

    10 Kensington security slot

    5

    Console Port

    11 Primary WAN port—VDSL/ADSL over
    POTS

    6

    PoE power connector (optional)

    Figure 1-31 shows the back panel for the Cisco 881-V router.
    Figure 1-31

    Back Panel of the Cisco 881-V Router

    6

    1

    2

    5

    4

    3

    Cisco Integrated Services Router Hardware Installation Guide

    1-62

    3

    246866

    C881VOICE

    7

    4

    5

    6

    7

    8

    9

    10



  • Page 83

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    1

    Fast Ethernet WAN port

    6

    PoE power connector (optional)

    2

    Voice BRI ports

    7

    Reset button

    3

    Voice ports—four FXS/DID ports and one
    FXO port.

    8

    Power connector

    4

    Fast Ethernet LAN—four ports

    9

    Earth ground connection

    5

    Console Port

    10 Kensington security slot

    Cisco 880 Series with Embedded WLAN Antennas
    Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas.
    These ISRs are fixed-platform routers that:


    Provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, and
    backup capabilities.



    Use single-band (2.4 GHz) WLAN cards or dual-band (2.4 GHz and 5 GHz) WLAN cards.



    Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a
    60-W power supply for POE-enabled routers.



    Have a fixed 512 MB of system memory.

    For information on configuring the Cisco 880 series ISRs, see Cisco 880 Series Integrated Services
    Router Software Configuration Guide.

    Cisco 887VA-WD
    Figure 1-32 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. The
    front panel has LEDs only. All the ports are in the back panel.
    Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

    OK

    PPP

    1

    0

    POE

    CD DATA

    LINK 2.4GHz 5GHz

    xDSL

    WLAN

    Cisco 800 Series
    FE LAN

    VPN

    0

    1

    2

    284983

    Figure 1-32

    3

    Cisco Integrated Services Router Hardware Installation Guide

    1-63



  • Page 84

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-33 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.
    Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

    9

    8

    overPOTS
    overPOTS

    Cisco
    Cisco 887VA-WD
    887VA-WD

    0
    0

    33

    22

    1

    O
    CONSOLE
    CONSOLE

    FE LAN
    FE LAN

    11

    00

    2

    AUX
    AUX

    POE OPTION
    POE OPTION
    REQUIRES 5A
    REQUIRES 5A
    POWER
    POWER
    ADAPTOR
    ADAPTOR RESET
    RESET

    3

    4 5

    1

    USB port

    6

    Power connector

    2

    4-port 10/100 Ethernet switch

    7

    Kensington security slot

    3

    Serial port—console or auxiliary

    8

    Power switch

    4

    Note

    5

    Reset button

    9
    No separate PoE power supply is
    required for routers with embedded
    WLAN antennas. For information on
    system power supply requirements
    when PoE is enabled, see the “Power
    over Ethernet Module” section on
    page 1-143.

    12VDC
    12VDC

    6

    284988
    284988

    Figure 1-33

    5A
    5A

    7

    VDSL/ADSL port

    C881WD
    Figure 1-34 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. The front
    panel has LEDs only. All the ports are in the back panel.
    Figure 1-34

    Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

    OK

    PPP

    1

    0

    POE

    FE4

    LINK 2.4GHz 5GHz

    WAN

    WLAN

    Cisco 800 Series
    VPN

    0

    1

    2

    3

    Cisco Integrated Services Router Hardware Installation Guide

    1-64

    284982

    FE LAN



  • Page 85

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-35 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs.
    Figure 1-35

    Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

    9

    Cisco 881WD

    O
    POE OPTION
    REQUIRES 5A
    POWER
    ADAPTOR

    0

    4

    1

    3

    2

    2

    1

    3

    0

    RESET
    12VDC

    AUX

    4

    284987

    CONSOLE

    FE LAN

    FE WAN

    5

    6

    5A

    7

    8

    1

    Primary WAN port—10/100 FE

    6

    Reset button

    2

    USB port

    7

    Power connector

    3

    4-port 10/100 Ethernet switch

    8

    Kensington security slot

    4

    Serial port—console or auxiliary

    9

    Power switch

    5

    Note

    No separate PoE power supply is
    required for routers with embedded
    WLAN antennas. For information on
    system power supply requirements
    when PoE is enabled, see the “Power
    over Ethernet Module” section on
    page 1-143.

    C881G-B/S/V-K9 ISRs
    The C881G-B-K9, C881G-S-K9, and C881G-V-K9 ISRs are members of the Cisco 880 series data
    routers. These routers provide integrated Virtual Private Network (VPN), 802.11b/g/n-compliant
    wireless Access Point (AP), 3G, and backup capabilities.
    For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
    Software Configuration Guide.

    C881GW-S/V-A-K9 ISRs
    The C881GW-S-A-K9 and C881GW-V-A-K9 ISRs are members of the Cisco 880G series data routers.
    These routers provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless
    AP, 3G, and backup capabilities.
    For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
    Software Configuration Guide.

    Cisco Integrated Services Router Hardware Installation Guide

    1-65



  • Page 86

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    C881G-U-K9 ISRs
    The C881G-U-K9 ISR is a member of the Cisco 880 series data routers. These routers provide integrated
    Virtual Private Network (VPN), embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless
    Access Point (AP), 3G, and backup capabilities.
    For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
    Software Configuration Guide.

    HSPA+ Versions of the Fixed-Platform ISRs
    The C881G+7-K9, C886VAG+7-K9, C887VAG+7-K9, C887VAMG+7-K9, C888EG+7-K9,
    C881GW+7-A-K9, C881GW+7-E-K9, C887VAGW+7-A-K9, and C887VAGW+7-E-K9 ISRs are
    members of the Cisco 880G series data routers. These routers provide integrated VPN, embedded Wi-Fi
    CERTIFIED™, 802.11b/g/n-compliant wireless AP, 3G, and backup capabilities.
    For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
    Software Configuration Guide.

    Cisco C881, C886, and C887 Series ISRs
    Cisco C881, C886, and C887 Series ISRs offer broadband speed and simplified management to small
    businesses, small enterprise branches, and teleworkers. The Cisco C881, C886, and C887 Series ISR
    models have a lead-free, fanless chassis and are updated versions of the previous Cisco 881, 886, and
    887 series (excluding 3G and wireless models).
    Information provided in this section is applicable for the following models:


    Cisco C881



    Cisco C886VA, Cisco C886VAJ (Annex J)



    Cisco C887VA, Cisco C887VAM (Annex M)

    Table 1-29 provides information about important hardware specifications pertaining to Cisco C881,
    C886, and C887 Series Routers.
    Table 1-29

    Hardware Specifications of Cisco C881, C886, and C887 Series
    Routers

    Hardware

    Description

    Flash Memory

    256 MB

    Main Memory

    1 GB DDR RAM; fixed and not extendable

    USB port

    A USB 2.0-compliant port located at the back
    panel

    FAN

    Fanless chassis

    PoE

    Two internal PoE ports

    WAN

    Cisco Integrated Services Router Hardware Installation Guide

    1-66



    C881— FE



    C886—VDSL/ADSL over ISDN with ISDN
    back up



    C887—VDSL/ADSL over POTS



  • Page 87

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Hardware

    Description

    Console or auxiliary port

    RJ-45

    LAN switch

    4-port 10/100BASE-T

    For detailed hardware specifications, see the Cisco 880 Series hardware data sheet at:
    http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_
    Data_Sheet.html

    Cisco C881 Router
    Figure 1-36 shows the front panel of the Cisco C881 Router.
    Figure 1-36

    Front Panel of the Cisco C881 Router
    OK

    PPP

    0

    1

    FE4
    FE

    WAN

    POE
    OE

    0

    1

    2

    3

    361124

    Cisco 800 Series
    FE LAN

    VPN

    1

    1

    LEDs

    For detailed description about the LEDs on the Cisco C880 Series Routers, see the “LEDs” section on
    page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-67



  • Page 88

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-37 shows the back panel of the Cisco C881 Router.
    Figure 1-37

    Back Panel of the Cisco C881 Router

    Cisco 881
    CONSOLE

    FE LAN

    FE WAN

    361125

    (POE)

    RESET
    0

    4

    1

    3

    2

    2

    1

    0

    AUX

    3

    12VDC

    4

    5

    2.5-5A

    7

    8 9

    6

    1

    Primary WAN port—FE

    6

    Reset button

    2

    USB port

    7

    Power connector

    3

    4-port 10/100 Ethernet switch

    8

    Earth ground connection

    4

    Serial port—Console or auxiliary

    9

    Kensington security slot

    5

    On/Off switch

    For information on installing the Cisco C880 Series Routers, see :
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco C886VA Router
    Figure 1-38 shows the front panel of the Cisco C886VA Router.
    Figure 1-38

    Front Panel of the Cisco C886VA Router
    OK

    PPP

    0

    1

    CD DATA

    POE
    OE

    xDSL

    VPN

    0

    1

    2

    ISDN

    3

    LINK

    B1

    B2

    361126

    Cisco 800 Series
    FE LAN

    1

    1

    LEDs

    For detailed description about the LEDs on the Cisco C880 Series Routers, see the “LEDs” section on
    page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-68



  • Page 89

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-39 shows the back panel of the Cisco C886VA Router.
    Figure 1-39

    Back Panel of the Cisco C886VA Router

    VDSL/ADSL

    CONSOLE

    FE LAN

    ISDN

    361127

    (POE)

    RESET
    0

    over ISDN

    1

    2

    0

    3

    3

    2

    1

    4

    0

    AUX

    5

    12VDC

    6

    2.5-5A
    2.
    -5A

    8

    9 10

    7

    1

    Primary WAN port—VDSL/ADSL over
    ISDN

    6

    On/Off switch

    2

    USB port

    7

    Reset button

    3

    ISDN

    8

    Power connector

    4

    4-port 10/100 Ethernet switch

    9

    Earth ground connection

    5

    Serial port—Console or auxiliary

    10 Kensington security slot

    For information on installing Cisco C880 Series Routers, see:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco C886VAJ Router
    Figure 1-40 shows the front panel of the Cisco C886VAJ Router.
    Figure 1-40

    Front Panel of the Cisco C886VAJ Router
    OK

    PPP

    0

    1

    CD DATA

    POE
    OE

    xDSL

    VPN

    0

    1

    2

    ISDN

    3

    LINK

    B1

    B2

    361128

    Cisco 800 Series
    FE LAN

    1

    1

    LEDs

    For detailed description about LEDs on the Cisco 880 Series Router, see the “LEDs” section on
    page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-69



  • Page 90

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-41 shows the back panel of the Cisco C886VAJ Router.
    Figure 1-41

    Back Panel of the Cisco C886VAJ Router

    VDSL/ADSL

    CONSOLE

    FE LAN

    ISDN

    361129

    (POE)

    RESET
    0

    over ISDN

    1

    2

    0

    3

    3

    2

    1

    4

    0

    AUX

    5

    12VDC

    6

    2. -5A
    2.5-5A

    8

    9 10

    7

    1

    Primary WAN port—VDSL/ADSL over
    ISDN

    6

    On/Off switch

    2

    USB port

    7

    Reset button

    3

    ISDN

    8

    Power connector

    4

    4-port 10/100 Ethernet switch

    9

    Earth ground connection

    5

    Serial port—Console or auxiliary

    10 Kensington security slot

    For information on installing Cisco C880 Series Routers, see:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco C887VA Router
    Figure 1-42 shows the front panel of the Cisco C887VA Router.
    Figure 1-42

    Front Panel of the Cisco C887VA Router

    OK

    PPP

    0

    1

    CD DATA

    POE
    OE

    xDSL

    Cisco 800 Series
    VPN

    0

    1

    2

    3

    361130

    FE LAN

    1

    1

    LEDs

    For detailed description about the LEDs on Cisco C880 Series Router, see the “LEDs” section on
    page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-70



  • Page 91

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-43 shows the back panel of the Cisco C887VA Router.
    Figure 1-43

    Back Panel of the Cisco C887VA Router

    Cisco 887
    887VA
    VDSL/ADSL

    CONSOLE

    FE LAN

    361131

    (POE)

    RESET
    0

    over POTS

    1

    3

    2

    2

    1

    0

    3

    AUX

    4

    12VDC

    5

    2.5-5A
    2.
    -5A

    7

    8 9

    6

    1

    Primary WAN port—VDSL/ADSL over
    POTS

    6

    Reset button

    2

    USB port

    7

    Power connector

    3

    4-port 10/100 Ethernet switch

    8

    Earth ground connection

    4

    Serial port—console or auxiliary

    9

    Kensington security slot

    5

    On/Off switch

    For information on installing Cisco C880 series routers, see the following link:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco C887VAM Router
    Figure 1-44 shows the front panel of the Cisco C887VAM router:
    Figure 1-44

    Front Panel of the Cisco C887VAM Router

    OK

    PPP

    0

    1

    CD DATA

    POE
    OE

    xDSL

    Cisco 800 Series
    VPN

    0

    1

    2

    3

    361132

    FE LAN

    1

    1

    LEDs

    For detailed description about LEDs on Cisco C880 series router, see “LEDs” section on page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-71



  • Page 92

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-45 shows the back panel of the Cisco C887VAM router.
    Figure 1-45

    Back Panel of the Cisco C887VAM Router

    Cisco 887
    887VAM
    AM
    VDSL/ADSL

    CONSOLE

    FE LAN

    361133

    (POE)

    RESET
    0

    over POTS

    1

    3

    2

    2

    1

    0

    AUX

    3

    4

    12VDC

    5

    2.5-5A
    2. -5A

    7

    8 9

    6

    1

    Primary WAN port—VDSL/ADSL over
    POTS

    6

    Reset button

    2

    USB port

    7

    Power connector

    3

    4-port 10/100 Ethernet switch

    8

    Earth ground connection

    4

    Serial port—Console or auxiliary

    9

    Kensington security slot

    5

    On/Off switch

    For information on installing the Cisco C880 Series Routers, see:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco Integrated Services Router Hardware Installation Guide

    1-72



  • Page 93

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Cisco C888 Integrated Services Router
    The Cisco C888 Integrated Services Router (ISR) offers broadband speeds and simplified management
    to small businesses, enterprise small branches, and teleworkers. The Cisco C888 ISR supports multi
    mode G.SHDSL (EFM+ATM) WAN connectivity. The Cisco C888 ISR has a lead free, fanless chassis
    and it is an updated version of the previous Cisco 888 (888 A and 888 EA) ISR models.
    Table 1-30 provides information about important hardware specifications pertaining to the Cisco C888
    ISR.
    Table 1-30

    Hardware Specifications for Cisco C888 ISR

    Hardware

    Description

    Flash Memory

    256 MB

    Main Memory

    1-GB DDR RAM ; fixed, and not extendable

    USB port

    A USB 2.0-compliant port located at the back
    panel

    FAN

    Fanless chassis.

    PoE

    Two internal PoE ports

    WAN

    4-pair multimode G.SHDSL (EFM+ATM) with
    ISDN backup.

    Console or auxiliary port

    RJ-45

    LAN switch

    4-port 10/100BASE-T

    Note

    If you change G.SHDSL mode from EFM to ATM or from ATM to EFM, you should reload the router.

    Note

    EFM auto mode is supported only on the first pair. EFM manual mode can be supported on all the 4 pairs.

    Note

    Cisco C888 ISR does not support Inverse Multiplexing over ATM (IMA) mode.

    For detailed hardware specifications, see the Cisco 880 Series hardware data sheet at:
    http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_
    Data_Sheet.html

    Cisco Integrated Services Router Hardware Installation Guide

    1-73



  • Page 94

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-46 shows the front panel of the Cisco C888 Router:
    Figure 1-46

    Front Panel of the Cisco C888 Router

    OK

    PPP

    0

    1

    CD DATA EFM ATM

    POE
    OE

    xDSL

    VPN

    0

    1

    2

    ISDN

    3

    LINK

    B1

    B2

    361134

    Cisco 800 Series
    FE LAN

    1

    1

    LEDs

    For detailed description about the LEDs on the Cisco 880 Series Routers, see information available at:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/1Overv
    iew880-860.html#wp1147924

    Cisco Integrated Services Router Hardware Installation Guide

    1-74



  • Page 95

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-47 shows the back panel of the Cisco C888 Router.
    Figure 1-47

    Back Panel of the Cisco C888 Router

    Cisco 888
    CONSOLE

    FE LAN

    ISDN

    SHDSL

    (POE)

    361135

    Chapter 1

    RESET
    RJ45
    J45 ONLY
    ON

    1

    0

    2

    0

    3

    3

    2

    1

    0

    AUX

    4

    5

    12VDC

    6

    2.5-5A
    2. -5A

    8

    9 10

    7

    1

    Primary WAN port—G.SHDSL

    6

    On/Off switch

    2

    USB port

    7

    Reset button

    3

    ISDN

    8

    Power connector

    4

    4-port 10/100 Ethernet switch

    9

    Earth ground connection

    5

    Serial port—console or auxiliary

    10 Kensington security slot

    For information on installing Cisco 800 Series Routers, see the information available at:
    http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/installin
    g.html#pgfId-1098019

    Cisco Integrated Services Router Hardware Installation Guide

    1-75



  • Page 96

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers
    Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers (ISRs) extend 4G LTE
    support to the existing Cisco 880 Series and Cisco 890 Series ISRs. The Cisco C880 Series and Cisco
    C890 Series 4G LTE ISRs are based on the Sierra Wireless MC7304 modem and Cisco C880 Series and
    Cisco C890 4G LTE Series ISRs can support higher data rates compared to 3G in both up link and down
    link directions with 4G LTE support.
    This section provides information about the following models:


    Cisco C881G-4G ISR



    Cisco C887VAG-4G ISR



    Cisco C896VAG-LTE ISR



    Cisco C897VAG-LTE ISR



    Cisco C898EAG-LTE ISR



    Cisco C899G-LTE ISR

    Table 1-31 provides information about important hardware specifications pertaining to Cisco C880 4G
    LTE Series ISRs.
    Table 1-31

    Hardware Specifications for Cisco C880 4G LTE Series ISRs

    Hardware

    Description

    Flash Memory

    1GB

    Main Memory

    1-GB DDR RAM

    USB port

    A USB 2.0-compliant port located at the back
    panel

    PoE

    Two PoE ports

    WAN



    C881G-4G— FE



    C887VAG-4G—VDSL or ADSL over POTS

    Console or auxiliary port

    RJ-45

    LAN switch

    4-port 10/100BASE-T

    Table 1-32 provides information about important hardware specifications pertaining to Cisco C890 4G
    LTE Series ISRs.
    Table 1-32

    Hardware Specifications for Cisco C890 4G LTE Series ISRs

    Hardware

    Description

    Flash Memory

    1 GB

    Main Memory

    1-GB DRAM

    USB port

    A USB 2.0-compliant port located at the back
    panel.

    PoE

    Four PoE ports

    Cisco Integrated Services Router Hardware Installation Guide

    1-76



  • Page 97

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-32

    Hardware Specifications for Cisco C890 4G LTE Series ISRs

    Hardware
    WAN

    Description


    C896VAG-LTE—VDSL or ADSL over
    ISDN, GE



    C897VAG-LTE—VDSL or ADSL over
    POTS, GE



    C898EAG-LTE—G.SHDSL over POTS, GE



    C899G-LTE—GE, SFP

    Console or auxiliary port

    RJ-45

    LAN switch

    8-port 10/100/1000 BASE-T

    Cisco Integrated Services Router Hardware Installation Guide

    1-77



  • Page 98

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-33 lists the different 4G LTE SKUs available for the Cisco 880 and Cisco 890 series ISRs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-78



  • Page 99

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs

    SKU ID
    C881G-4G-GA-K9

    Mode

    Operating
    Region

    Frequency Band



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Description
    Cisco 880 Series ISR
    Multimode LTE
    feature for global
    wireless networks.
    C881G-4G-GA-K9
    comes with a Sierra
    Wireless MC7304
    modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):

    C886VAG-LTE-GAK9



    850 MHz



    900 MHz



    1800 MHz



    1900 MHz



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Cisco 880 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C886VAG-LTE-GA-K
    9 comes with a Sierra
    Wireless MC7304
    modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):


    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Cisco Integrated Services Router Hardware Installation Guide

    1-79



  • Page 100

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID

    Mode

    C887VAG-4G-GAK9

    Operating
    Region

    Frequency Band



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Description
    Cisco 880 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C887VAG-4G-GA-K9
    comes with a Sierra
    Wireless MC7304
    modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):

    C896VAG-LTE-GAK9



    850 MHz



    900 MHz



    1800 MHz



    1900 MHz



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):

    Cisco Integrated Services Router Hardware Installation Guide

    1-80



    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Cisco 890 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C896VAG-LTE-GA-K
    9 comes with a Sierra
    Wireless MC7304
    modem.



  • Page 101

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID
    C897VAG-LTE-GAK9

    Mode

    Operating
    Region

    Frequency Band



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, 4G:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Description
    Cisco 890 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C897VAG-LTE-GA-K
    9 comes with a Sierra
    Wireless MC7304
    modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):

    C897VAMG-LTE-G
    A-K9



    850 MHz



    900 MHz



    1800 MHz



    1900 MHz



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Cisco 890 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C897VAMG-LTE-GA
    -K9 comes with a
    Sierra Wireless
    MC7304 modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):


    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Cisco Integrated Services Router Hardware Installation Guide

    1-81



  • Page 102

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID

    Mode

    C897VAG-LTE-LAK9

    Operating
    Region

    Frequency Band

    Description

    Latin America

    For FDD LTE:

    C897VAG-LTE-LA-K
    9 is a dedicated
    Multimode LTE SKU
    for Latin American
    wireless networks and
    comes with a Sierra
    Wireless MC7430
    modem.



    LTE



    HSPA+



    700 MHz (band 28)



    HSPA



    850 MHz (band 5)



    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:

    Cisco Integrated Services Router Hardware Installation Guide

    1-82



    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)



  • Page 103

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID
    C898EAG-LTE-GA
    -K9

    Mode

    Operating
    Region

    Frequency Band



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Description
    Cisco 890 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C898EAG-LTE-GA-K
    9 comes with a Sierra
    Wireless MC7304
    modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):


    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Cisco Integrated Services Router Hardware Installation Guide

    1-83



  • Page 104

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID

    Mode

    C898EAG-LTE-LAK9

    Operating
    Region

    Frequency Band

    Description

    ASEAN

    For FDD LTE:

    C898EAG-LTE-LA-K
    9 is a dedicated
    Multimode LTE SKU
    for Asean wireless
    networks and comes
    with a Sierra Wireless
    MC7430 modem.



    LTE



    HSPA+



    700 MHz (band 28)



    HSPA



    850 MHz (band 5)



    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:

    Cisco Integrated Services Router Hardware Installation Guide

    1-84



    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)



  • Page 105

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID
    C899G-LTE-LA-K9

    Mode


    LTE



    HSPA+




    Operating
    Region
    Latin America
    and APAC

    Frequency Band

    Description

    For FDD LTE:

    C899G-LTE-LA-K9 is
    a dedicated Multimode
    LTE SKU for Latin
    American and APAC
    wireless networks and
    comes with a Sierra
    Wireless MC7430
    modem.



    700 MHz (band 28)

    HSPA



    850 MHz (band 5)

    UMTS



    800 MHz (band 19)



    800 MHz (band 18)



    900 MHz (band 8)



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    For TDD LTE:


    1900 MHz (Band 39)



    2300 MHz (Band 40)



    2500 MHz (Band 41)



    2600 MHz (Band 38)

    For UMTS, HSPA+, HSPA:


    800 MHz (band 6)



    800 MHz (band 19)



    850 MHz (band 5)



    900 MHz (band 8)



    1700 MHz (band 9)



    2100 MHz (band 1)

    Cisco Integrated Services Router Hardware Installation Guide

    1-85



  • Page 106

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID

    Mode

    C899G-LTE-GA-K9

    Operating
    Region

    Frequency Band



    LTE



    HSPA+



    HSPA



    UMTS



    1800 MHz (band 3)



    EDGE



    2100 MHz (band 1)



    GPRS



    2600 MHz (band 7)

    Global (Europe, LTE:
    New Zealand,
    • 800 MHz (band 20)
    and Australia)
    • 900 MHz (band 8)

    Description
    Cisco 890 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C899G-LTE-GA-K9
    comes with a Sierra
    Wireless MC7304
    modem.

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):

    C899G-LTE-VZ-K9

    LTE

    North America
    (Verizon)
    • EVDO Rev-A






    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    LTE:

    1xRTT



    AWS (band 4)



    700 MHz (band 13)



    PCS 1900 MHz (band 25)

    3G:


    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    2G:

    Cisco Integrated Services Router Hardware Installation Guide

    1-86



    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    Cisco 890 series ISR
    with Multimode LTE
    feature for Verizon
    wireless networks.
    C899G-LTE-VZ-K9
    comes with a Sierra
    Wireless MC7350
    modem.



  • Page 107

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID
    C899G-LTE-NA-K9

    Mode


    LTE



    HSPA+



    HSPA



    UMTS



    EDGE



    GPRS

    Operating
    Region
    North America
    (AT&T,
    Bell-Canada,
    Roger, Telus,
    and other
    GSM/LTE
    operators in
    USA and
    Canada)

    Frequency Band

    Description

    LTE:

    Cisco 890 series ISR
    with Multimode LTE
    feature for wireless
    networks in USA and
    Canada.
    C899G-LTE-NA-K9
    comes with a Sierra
    Wireless MC7354
    modem.



    AWS (band 4)



    700 MHz (band 5)



    850 MHz (band 17)



    1900 MHz (band 2)



    2600 MHz (band 7)

    3G (UMTS, HSPA+, HSPA):


    1900 MHz (band 2)



    AWS (band 4)



    850 (band 5)

    2G (GSM, EDGE, GPRS):


    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Cisco Integrated Services Router Hardware Installation Guide

    1-87



  • Page 108

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-33

    Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)

    SKU ID

    Mode

    C899G-LTE-ST-K9



    LTE



    EVDO Rev-A



    1xRTT

    Operating
    Region
    North America
    (Sprint)

    Frequency Band

    Description

    LTE:

    Cisco 890 series ISR
    with Multimode LTE
    feature for Sprint
    wireless networks.
    C899G-LTE-ST-K9
    comes with a Sierra
    Wireless MC7350
    modem.



    AWS (band 4)



    700 MHz (band 13)



    PCS 1900 MHz (band 25)

    3G:


    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)

    2G:

    C899G-LTE-JP-K9



    800 MHz (band class 0)



    1900 MHz (band class 1)



    800 MHz (band class 10)



    LTE



    HSPA+



    800 MHz (band 20)



    HSPA



    850 MHz (band 19)



    UMTS



    900 MHz (band 8)



    EDGE



    1500 MHz (band 21)



    GPRS



    1800 MHz (band 3)



    2100 MHz (band 1)



    2600 MHz (band 7)

    Global (Japan)

    LTE:

    3G (UMTS, HSPA+, HSPA):


    800 MHz (band 6)



    850 MHz (band 5)



    900 MHz (band 8)



    1900 MHz (band 2)



    2100 MHz (band 1)

    2G (GSM, EDGE, GPRS):

    Cisco Integrated Services Router Hardware Installation Guide

    1-88



    850 MHz



    900 MHz



    1800 MHz



    1900 MHz

    Cisco 890 series ISR
    with Multimode LTE
    feature for global
    wireless networks.
    C899G-LTE-JP-K9
    comes with a Sierra
    Wireless MC7330
    modem.



  • Page 109

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Cisco C881G-4G Integrated Services Router
    Figure 1-48 shows the front panel of the Cisco C881G-4G ISR.
    Figure 1-48

    Front Panel of the Cisco C881G-4G ISR

    2

    4
    3

    5

    372528

    1

    6

    7

    8

    9

    10

    11

    1

    Power OK

    7

    FE LAN

    2

    PPP

    8

    GPS

    3

    PoE

    9

    RSSI

    4

    FE WAN Port

    10 4G

    5

    SIM

    11 WWAN

    6

    VPN

    Table 1-34 describes the LEDs of the Cisco C881G-4G ISR.
    Table 1-34

    LED Descriptions for the Cisco C881G-4G ISR

    Number

    LED

    Color

    Description

    1

    Power OK

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.
    Blinking—Boot up is in process, or the router is in
    ROMMON mode.
    Off—Power is not supplied to the router.

    2

    PPP

    Green

    On—At least one PPP session is established.

    3

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    4

    FE WAN
    Port Link

    Amber

    On—Fault with the PoE.

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Port is not connected.

    Cisco Integrated Services Router Hardware Installation Guide

    1-89



  • Page 110

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-34

    LED Descriptions for the Cisco C881G-4G ISR

    Number

    LED

    Color

    5

    SIM

    Green / Yellow SIM in slot 0 is active, SIM in slot 1 is not.
    (one green blink
    followed by two
    yellow blinks)
    Yellow / Green
    (one yellow
    blink followed
    by two green
    blinks)

    Description

    SIM in slot 1 active, SIM in slot 0 is not.

    Off / Green (two No SIM in slot 0, SIM present in slot 1.
    green blinks
    and then a
    pause)
    Green / Off

    SIM is present in slot0, no SIM in slot 1.

    (slow blink
    once and then a
    pause)
    Off / Off

    No SIM present in either slots.

    6

    VPN

    Green

    On—VPN is connected.

    7

    FE LAN
    Port Links
    Status

    Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or being
    transmitted.
    Off—Ethernet port is not connected.

    8

    GPS

    Green (solid)

    Standalone GPS.

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow (solid)

    Assisted GPS.

    Yellow (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    9

    RSSI

    Green (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    10

    Service

    Green (solid)

    Service is active and the corresponding LED is lit based
    on the service level that is active (2G, 3G,3.7G, LTE).

    Off

    No service.

    Cisco Integrated Services Router Hardware Installation Guide

    1-90



  • Page 111

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-34

    LED Descriptions for the Cisco C881G-4G ISR

    Number

    LED

    Color

    Description

    11

    WWAN

    Green

    Module is powered on and connected but not
    transmitting or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    Cisco Integrated Services Router Hardware Installation Guide

    1-91



  • Page 112

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-49 shows the back panel of the Cisco C881G-4G ISR.
    Figure 1-49

    Back Panel of the Cisco C881G-4G ISR

    13

    12

    11

    372522

    14

    1

    2

    3

    4

    5

    6

    7

    8

    1

    Primary WAN port—FE

    9

    Earth ground connection

    2

    USB port

    10

    Kensington security slot

    3

    4G port

    11 4G Antenna connector—M1/DIV

    4

    SIM slots

    12

    5

    4-port 10/100 Ethernet switch

    13 Active GPS antenna connector

    6

    Serial port—Console or auxiliary

    14

    7

    Reset button

    8

    Power connector

    9

    10

    Power switch
    4G Antenna connector—M0/MAIN

    For information on installing the Cisco C880 Series Routers, see:
    http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG.html

    Cisco C886VAG-LTE
    Figure 1-50 shows the front panel of the Cisco C886VAG-LTE ISR.
    Figure 1-50

    Front Panel of the Cisco C886VAG-LTE ISR

    2

    4
    3

    5

    372529

    1

    6

    7

    8

    Cisco Integrated Services Router Hardware Installation Guide

    1-92

    9

    10

    11



  • Page 113

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-35 describes the LEDs for Cisco C886VAG-LTE ISR.
    Table 1-35

    LED Descriptions for the Cisco C886VAG-LTE ISR

    Number

    LED

    Color

    Description

    1

    Power OK

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.
    Blinking—Boot up is in process, or the router is in
    ROMMON mode.
    Off—Power is not supplied to the router.

    2

    PPP

    Green

    On—At least one PPP session is established.

    3

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    4

    xDSL CD

    Amber

    On—Fault with the PoE.

    Green

    On—The xDSL interface is connected to the DSLAM.
    Blinking—Training the line.
    Off—Indicates that a connection has not been established
    or the port is shut down.

    xDSL Data Green

    Blinking—The xDSL interface is either receiving or
    transmitting data.
    Off—No data is being transmitted or received.

    5

    SIM

    Green / Yellow SIM in slot 0 is active, SIM in slot 1 is not.
    (one green blink
    followed by two
    yellow blinks)
    Yellow / Green
    (one yellow
    blink followed
    by two green
    blinks)

    SIM in slot 1 is active, SIM in slot 0 is not.

    Off / Green (two No SIM in slot 0, SIM present in slot 1.
    green blinks and
    then a pause)
    Green / Off

    SIM present in slot0, no SIM in slot 1.

    (slow blink once
    and then a
    pause)
    Off / Off

    No SIM present in either slots.

    6

    VPN

    Green

    On—VPN is connected.

    7

    FE LAN
    Port Links
    Status

    Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Ethernet port is not connected.

    Cisco Integrated Services Router Hardware Installation Guide

    1-93



  • Page 114

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-35

    LED Descriptions (continued)for the Cisco C886VAG-LTE ISR

    Number

    LED

    Color

    Description

    8

    GPS

    Green (solid)

    Standalone GPS.

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow (solid

    Assisted GPS.

    Yellow (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    9

    RSSI

    Green (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    10

    Service

    Green (Solid)

    Service is active and the corresponding LED is lit based on
    the service level that is active (2G, 3G, 3.7G, LTE).

    Off

    No service.

    Green

    Module is powered on and connected but not transmitting
    or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    11

    WWAN

    Cisco Integrated Services Router Hardware Installation Guide

    1-94



  • Page 115

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-51 shows the back panel of the Cisco C886VAG-LTE ISR.
    Figure 1-51

    Back Panel of the Cisco C886VAG-LTE ISR

    14

    13

    12

    11

    10

    365672

    Cisco 886VAG-LTE

    1

    2

    3

    4

    5

    6

    7

    8

    9

    1

    USB port

    8

    Earth ground connection

    2

    LTE port

    9

    Kensington security slot

    3

    SIM slots

    10 LTE antenna connector—M1/DIV

    4

    4-port 10/100 Ethernet switch

    11 Power switch

    5

    Serial port—Console or auxiliary

    12 Active GPS antenna connector

    6

    Reset button

    13 Primary WAN port—VDSL or ADSL over
    ISDN

    7

    Power connector

    14 LTE antenna connector—M0/MAIN

    Cisco C887VAG-4G Integrated Services Router
    Figure 1-52 shows the front panel of the Cisco C887VAG-4G ISR.
    Front Panel of the Cisco C887VAG-4G ISR

    2
    1

    4
    3

    5

    372529

    Figure 1-52

    6

    7

    8

    9

    10

    11

    Cisco Integrated Services Router Hardware Installation Guide

    1-95



  • Page 116

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-36 describes the LEDs for Cisco C887VAG-4G ISR.
    Table 1-36

    LED Descriptions for the Cisco C887VAG-4G ISR

    Number

    LED

    Color

    Description

    1

    Power OK

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.
    Blinking—Boot up is in process, or the router is in
    ROMMON mode.
    Off—Power is not supplied to the router.

    2

    PPP

    Green

    On—At least one PPP session is established.

    3

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    4

    xDSL CD

    Amber

    On—Fault with the PoE.

    Green

    On—The xDSL interface is connected to the DSLAM.
    Blinking—Training the line.
    Off—Indicates that a connection has not been established
    or the port is shut down.

    xDSL Data Green

    Blinking—The xDSL interface is either receiving or
    transmitting data.
    Off—No data is being transmitted or received.

    5

    SIM

    Green / Yellow SIM in slot 0 is active, SIM in slot 1 is not.
    (one green blink
    followed by two
    yellow blinks)
    Yellow / Green
    (one yellow
    blink followed
    by two green
    blinks)

    SIM in slot 1 is active, SIM in slot 0 is not.

    Off / Green (two No SIM in slot 0, SIM present in slot 1.
    green blinks and
    then a pause)
    Green / Off

    SIM present in slot0, no SIM in slot 1.

    (slow blink once
    and then a
    pause)
    Off / Off

    No SIM present in either slots.

    6

    VPN

    Green

    On—VPN is connected.

    7

    FE LAN
    Port Links
    Status

    Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Ethernet port is not connected.

    Cisco Integrated Services Router Hardware Installation Guide

    1-96



  • Page 117

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-36

    LED Descriptions (continued)for the Cisco C887VAG-4G ISR

    Number

    LED

    Color

    Description

    8

    GPS

    Green (solid)

    Standalone GPS.

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow (solid

    Assisted GPS.

    Yellow (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    9

    RSSI

    Green (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    10

    Service

    Green (Solid)

    Service is active and the corresponding LED is lit based on
    the service level that is active (2G, 3G, 3.7G, LTE).

    Off

    No service.

    Green

    Module is powered on and connected but not transmitting
    or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    11

    WWAN

    Cisco Integrated Services Router Hardware Installation Guide

    1-97



  • Page 118

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-53 shows the back panel of the Cisco C887VAG-4G ISR.
    Figure 1-53

    Back Panel of the Cisco C887VAG-4G ISR

    13

    12

    11

    10

    372523

    14

    1

    2

    3

    4

    5

    6

    7

    8

    9

    1

    USB port

    8

    Earth ground connection

    2

    4G port

    9

    Kensington security slot

    3

    SIM slots

    10

    4G antenna connector—M1/DIV

    4

    4-port 10/100 Ethernet switch

    11 Power switch

    5

    Serial port—Console or auxiliary

    12 Active GPS antenna connector

    6

    Reset button

    13 Primary WAN port—VDSL or ADSL over
    POTS

    7

    Power connector

    14 4G antenna connector—M0/MAIN

    Cisco C896VAG-LTE Integrated Services Router
    Figure 1-54 shows the front panel of the Cisco C896VAG-LTE ISR.
    Figure 1-54

    Front Panel of the Cisco C896VAG-LTE ISR

    4

    2
    3

    5

    372530

    1

    6

    8
    7

    10
    9

    Cisco Integrated Services Router Hardware Installation Guide

    1-98

    11

    12
    13



  • Page 119

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-37 describes the LEDs for Cisco C896VAG-LTE ISR.
    Table 1-37

    LED Descriptions for Cisco C896VAG-LTE ISR

    Number LED

    Color

    Description

    1

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.

    Power OK

    Blinking—Boot up is in process, or the router is in
    ROMMON mode
    Off—Power is not supplied to the router.
    2

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    Amber
    3

    GE LAN PoE
    Ports

    On—Fault with the PoE.

    Green/Ambe Green On—Ethernet port is connected.
    r
    Amber On—Fault with PoE. There is a fault with the
    in-line power supply.
    Green/Amber Blinking—Data is either being received or
    being transmitted.
    Green/Amber Off—Ethernet port is not connected.

    4

    GE LAN Ports

    Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or being
    transmitted.
    Off—Ethernet port is not connected.

    5

    GE WAN Ports

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Port is not connected.

    SFP WAN port

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—No link

    6

    VPN

    Green

    On—VPN is connected.

    7

    PPP

    Green

    On—At least one PPP session is established.

    8

    xDSL CD

    Green

    On—The xDSL interface is connected to the DSLAM.
    Blinking—Training the line.
    Off—Indicates that a connection has not been
    established or the port is shut down.

    xDSL Data

    Green

    Blinking—The xDSL interface is either receiving or
    transmitting data.
    Off—No data is being transmitted or received.

    Cisco Integrated Services Router Hardware Installation Guide

    1-99



  • Page 120

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-37

    LED Descriptions (continued)for Cisco C896VAG-LTE ISR

    Number LED

    Color

    Description

    9

    Green /
    Yellow (one
    green blink
    followed by
    two yellow
    blinks)

    SIM in slot 0 is active, SIM in slot 1 is not.

    SIM

    SIM in slot 1 is active, SIM in slot 0 is not.
    Yellow /
    Green (one
    yellow blink
    followed by
    two green
    blinks)
    Off / Green No SIM in slot 0, SIM is present in slot 1.
    (two green
    blinks and
    then a pause)

    10

    Service

    Green / Off
    (slow green
    blink once
    and then a
    pause)

    SIM is present in slot0, no SIM in slot 1.

    Off / Off

    No SIM present in either slots.

    Green
    (Solid)

    Service is active and the corresponding LED is lit based
    on the service level that is active (2G, 3G, 3.5G, 3.7G,
    LTE).

    Off

    No service.

    11

    RSSI

    Green
    (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    12

    GPS

    Green
    (solid)

    Standalone GPS.

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow
    (solid)

    Assisted GPS.

    Yellow
    (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    Cisco Integrated Services Router Hardware Installation Guide

    1-100



  • Page 121

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-37

    LED Descriptions (continued)for Cisco C896VAG-LTE ISR

    Number LED

    Color

    Description

    13

    Green

    Module is powered on and connected but not
    transmitting or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    WWAN

    Figure 1-55 shows the back panel of the Cisco C896VAG-LTE ISR.
    Figure 1-55

    Back Panel of the Cisco C896VAG-LTE ISR

    16

    15

    14

    13

    372524

    Chapter 1

    1

    2

    3

    4

    5

    6

    7

    8 9 10

    11 12

    Cisco Integrated Services Router Hardware Installation Guide

    1-101



  • Page 122

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    1

    GE WAN interface

    9

    2

    SFP port

    10 Reset button

    3

    4G port

    11 Earth ground connection

    4

    USB port

    12 Kensington security slot

    5

    SIM slots

    13 4G antenna connector—M1/DIV

    6

    8-port Gigabit Ethernet switch

    14 Active GPS antenna connector

    7

    Console / Auxiliary port

    15 VDSL or ADSL over ISDN

    8

    Power connector

    16 4G antenna connector—M0/MAIN

    On/Off switch

    For information on installing Cisco C890 Series Routers, see the following link:
    http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG.html

    Cisco C897VAG-LTE Integrated Service Router
    Figure 1-56 shows the front panel of the Cisco C897VAG-LTE ISR.
    Figure 1-56

    Front Panel of the Cisco C897VAG-LTE ISR

    4

    2
    3

    5

    372531

    1

    6

    8
    7

    10
    9

    Cisco Integrated Services Router Hardware Installation Guide

    1-102

    11

    12
    13



  • Page 123

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-38 describes the LEDs for the Cisco C897VAG-LTE ISR.
    Table 1-38

    LED Descriptions for the Cisco C897VAG-LTE ISR

    Number LED

    Color

    Description

    1

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.

    Power OK

    Blinking—Boot up is in process, or the router is in
    ROMMON mode.
    Off—Power is not supplied to the router.
    2

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    Amber
    3

    GE LAN PoE
    Ports

    On—Fault with the PoE.

    Green/Ambe Green On—Ethernet port is connected.
    r
    Amber On—Fault with PoE. There is a fault with the
    in-line power supply.
    Green/Amber Blinking—Data is either being received or
    being transmitted.
    Green/Amber Off—Ethernet port is not connected.

    4

    GE LAN Ports

    Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Ethernet port is not connected.

    5

    GE WAN Ports

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Port is not connected.

    SFP WAN port

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—No link

    6

    VPN

    Green

    On—VPN is connected.

    7

    PPP

    Green

    On—At least one PPP session is established.

    8

    xDSL CD

    Green

    On—The xDSL interface is connected to the DSLAM.
    Blinking—Training the line.
    Off—Indicates that a connection has not been
    established or the port is shut down.

    xDSL Data

    Green

    Blinking—The xDSL interface is either receiving or
    transmitting data.
    Off—No data is being transmitted or being received.

    Cisco Integrated Services Router Hardware Installation Guide

    1-103



  • Page 124

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-38

    LED Descriptions (continued)for the Cisco C897VAG-LTE ISR

    Number LED

    Color

    Description

    9

    Green /
    Yellow (one
    green blink
    followed by
    two yellow
    blinks)

    SIM in slot 0 is active, SIM in slot 1 is not.

    SIM

    SIM in slot 1 is active, SIM in slot 0 is not.
    Yellow /
    Green (one
    yellow blink
    followed by
    two green
    blinks)
    Off / Green No SIM in slot 0, SIM is present in slot 1.
    (two green
    blinks and
    then a pause)

    10

    Service

    Green / Off
    (slow green
    blink once
    and then a
    pause)

    SIM is present in slot0, no SIM in slot 1.

    Off / Off

    No SIM present in either slots.

    Green
    (solid)

    Service is active and the corresponding LED is lit based
    on the service level that is active (2G, 3G, 3.5G, 3.7G,
    LTE).

    Off

    No service.

    11

    RSSI

    Green
    (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    12

    GPS

    Green
    (solid)

    Standalone GPS.

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow
    (solid)

    Assisted GPS.

    Yellow
    (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    Cisco Integrated Services Router Hardware Installation Guide

    1-104



  • Page 125

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-38

    LED Descriptions (continued)for the Cisco C897VAG-LTE ISR

    Number LED

    Color

    Description

    13

    Green

    Module is powered on and connected, but not
    transmitting or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    WWAN

    Figure 1-57 shows the back panel of the Cisco C897VAG-LTE ISR.
    Figure 1-57

    Back Panel of the Cisco C897VAG-LTE ISR

    15

    14

    13

    372525

    16

    1

    2

    3

    4

    5

    6

    7

    8 9 10

    11 12

    1

    GE WAN interface

    9

    2

    SFP port

    10 Reset button

    3

    4G port

    11 Earth ground connection

    4

    USB port

    12 Kensington security slot

    5

    SIM slots

    13 4G antenna connector—M1/DIV

    6

    8-port Gigabit Ethernet switch

    14 Active GPS antenna connector

    7

    Console/Auxiliary port

    15 VDSL or ADSL over POTS

    8

    Power connector

    16 4G antenna connector—M0/MAIN

    On/Off switch

    Cisco C898EAG-LTE Integrated Service Router
    Figure 1-58 shows the front panel of the Cisco C898EAG-LTE ISR.
    Figure 1-58

    Front Panel of the Cisco C898EAG-LTE ISR

    Cisco Integrated Services Router Hardware Installation Guide

    1-105



  • Page 126

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    4

    2
    3

    5

    372532

    1

    6

    8
    7

    10
    9

    11

    12
    13

    Table 1-39 describes the LEDs for the Cisco C898EAG-LTE ISR.
    Table 1-39

    LED Descriptions for the Cisco C898EAG-LTE ISR

    Number LED

    Color

    Description

    1

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.

    Power OK

    Blinking—Boot up is in process, or the router is in
    ROMMON mode.
    Off—Power is not supplied to the router.
    2

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    Amber
    3

    GE LAN PoE
    Ports

    On—Fault with the PoE.

    Green/Ambe Amber On—Ethernet port is connected.
    r
    Amber On—Fault with PoE. There is a fault with the
    in-line power supply.
    Green/Amber Blinking—Data is either being received or
    transmitted.
    Green/Amber Off—Ethernet port is not connected.

    4

    GE LAN Ports

    Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Ethernet port is not connected.

    5

    GE WAN Ports

    Green

    On—Port is connected.
    Blinking—Data is either being received or being
    transmitted.
    Off—Port is not connected.

    SFP WAN port

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—No link

    6

    VPN

    Green

    Cisco Integrated Services Router Hardware Installation Guide

    1-106

    On—VPN is connected.



  • Page 127

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-39

    LED Descriptions (continued)for the Cisco C898EAG-LTE ISR

    Number LED

    Color

    Description

    7

    PPP

    Green

    On—At least one PPP session is established.

    8

    xDSL CD

    Green

    On—The xDSL interface is connected to the DSLAM40.
    Blinking—Training the line.
    Off—Indicates that a connection has not been
    established or the port is shut down.

    xDSL Data

    Green

    Blinking—The xDSL interface is either receiving or
    transmitting data.
    Off—No data is being transmitted or being received.

    xDSL EFM

    Green

    Blink—The router is operating in EFM mode.
    Off—Not operating in EFM mode.

    9

    SIM

    Green /
    Yellow (one
    green blink
    followed by
    two yellow
    blinks)

    SIM in slot 0 is active, SIM in slot 1 is not.

    SIM in slot 1 is active, SIM in slot 0 is not.
    Yellow /
    Green (one
    yellow blink
    followed by
    two green
    blinks)
    Off / Green No SIM in slot 0, SIM present in slot 1.
    (two green
    blinks and
    then a pause)

    10

    11

    Service

    RSSI

    Green / Off
    (slow green
    blink once
    and then a
    pause)

    SIM is present in slot0, no SIM in slot 1.

    Off / Off

    No SIM present in either slot.

    Green
    (Solid)

    Service is active and the corresponding LED is lit based
    on the service level which is active (2G, 3G, 3.5G, 3.7 G,
    LTE).

    Off

    No service.

    Green
    (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-107



  • Page 128

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-39

    LED Descriptions (continued)for the Cisco C898EAG-LTE ISR

    Number LED

    Color

    Description

    12

    Green
    (solid)

    Standalone GPS

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow
    (solid)

    Assisted GPS.

    Yellow
    (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    Green

    Module is powered on and connected, but not
    transmitting or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    13

    GPS

    WWAN

    Cisco Integrated Services Router Hardware Installation Guide

    1-108



  • Page 129

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-59 shows the back panel of the Cisco C898EAG-LTE ISR.
    Figure 1-59

    Back Panel of the Cisco C898EAG-LTE ISR

    15

    14

    13

    372526

    16

    1

    2

    3

    4

    5

    6

    7

    8 9 10

    11 12

    1

    GE WAN interface

    9

    2

    SFP port

    10 Reset button

    3

    4G port

    11 Earth ground connection

    4

    USB port

    12 Kensington security slot

    5

    SIM slots

    13 4G antenna connector—M1/DIV

    6

    8-port Gigabit Ethernet switch

    14 Active GPS antenna connector

    7

    Console/Auxiliary port

    15 G.SHDSL over POTS

    8

    Power connector

    16 4G antenna connector—M0/MAIN

    On/Off switch

    Cisco C899G-LTE Integrated Service Router
    Figure 1-60 shows the front panel of the Cisco C899G-LTE ISR.
    Front Panel of the Cisco C899G-LTE ISR

    4

    2
    1

    3

    5

    372533

    Figure 1-60

    8

    6
    7

    10
    9

    12
    11

    Cisco Integrated Services Router Hardware Installation Guide

    1-109



  • Page 130

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-40 describes the LEDs for the Cisco C899G-LTE ISR.
    Table 1-40

    LED Descriptions for the Cisco C899G-LTE ISR

    Number LED

    Color

    Description

    1

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.

    Power OK

    Blinking—Boot up is in process, or the router is in
    ROMMON mode.
    Off—Power is not supplied to the router.
    2

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    3

    GE LAN PoE
    Ports

    Amber

    On—Fault with the PoE.

    Green

    Green On—Ethernet port is connected.
    Amber On—Fault with PoE. There is a fault with the
    in-line power supply.
    Green/Amber Blinking—Data is either being received or
    transmitted.
    Green/Amber Off—Ethernet port is not connected.

    4

    GE LAN Ports Green

    On—Ethernet port is connected.
    Blinking—Data is either being received or being
    transmitted.
    Off—Ethernet port is not connected.

    5

    GE WAN
    Ports

    Green

    On—Port is connected.
    Blinking—Data is either being received or transmitted.
    Off—Port is not connected.

    SFP WAN port Green

    On—Port is connected.
    Blinking—Data is either being received or being
    transmitted.
    Off—No link

    6

    VPN

    Green

    On—VPN is connected.

    7

    PPP

    Green

    On—At least one PPP session is established.

    Cisco Integrated Services Router Hardware Installation Guide

    1-110



  • Page 131

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-40

    LED Descriptions for the Cisco C899G-LTE ISR (continued)

    Number LED

    Color

    Description

    8

    Green / Yellow
    (one green blink
    followed by two
    yellow blinks)

    SIM in slot 0 is active, SIM in slot 1 is not.

    SIM

    SIM in slot 1 is active, SIM in slot 0 is not.
    Yellow / Green
    (one yellow blink
    followed by two
    green blinks)
    Off / Green (two
    green blinks and
    then a pause)

    No SIM in slot 0, SIM present in slot 1.

    Green / Off (slow SIM is present in slot0, no SIM in slot 1.
    green blink once
    and then a pause)
    9

    Service

    Off / Off

    No SIM present in either slots.

    Green (Solid)

    Service is active and the corresponding LED is lit based
    on the service level which is active (2G, 3G, 3.5G, 3.7G,
    LTE).

    Off

    No service.

    10

    RSSI

    Green (solid)

    Signal strength bars are indicated by the corresponding
    LEDs.

    11

    GPS

    Green (solid)

    Standalone GPS.

    Green (slow
    blinking)

    GPS is acquiring signals.

    Yellow (solid)

    Assisted GPS.

    Yellow (slow
    blinking)

    Assisted GPS is acquiring signals.

    Off

    GPS is not configured.

    Green

    Module is powered on and connected, but not
    transmitting or receiving.

    Green (slow
    blinking)

    Module is powered on and searching for connection.

    Green (fast
    blinking)

    Module is transmitting or receiving.

    Off

    Module is not powered.

    12

    WWAN

    Cisco Integrated Services Router Hardware Installation Guide

    1-111



  • Page 132

    Chapter 1
    Cisco 860, 880, 890 Series

    Figure 1-61 shows the back panel of the Cisco C899G-LTE ISR.
    Figure 1-61

    Back Panel of the Cisco C899G-LTE ISR

    Cisco Integrated Services Router Hardware Installation Guide

    1-112

    Product Overview



  • Page 133

    Product Overview
    Cisco 860, 880, 890 Series

    16

    15

    14

    372527

    Chapter 1

    1

    2

    3

    4

    5

    6

    7

    8

    9 10 11

    12 13

    1

    GE WAN interface

    9

    2

    GE WAN interface

    10 On/Off switch

    3

    SFP port

    11 Reset button

    4

    4G port

    12 Earth ground connection

    5

    USB port

    13 Kensington security slot

    6

    SIM slots

    14 4G antenna connector—M1/DIV

    7

    8-port Gigabit Ethernet switch

    15 Active GPS antenna connector

    8

    Console/Auxiliary port

    16 4G antenna connector—M0/MAIN

    Power connector

    Cisco Integrated Services Router Hardware Installation Guide

    1-113



  • Page 134

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Cisco 890 Series Integrated Service Routers
    This section contains the following topics:


    Cisco 891, Cisco 892, and Cisco 892F, page 1-114



    Cisco C897VAB-K9, page 1-124

    Cisco 891, Cisco 892, and Cisco 892F
    The Cisco 891, Cisco 892, and Cisco 892F ISRs have the following features:


    Integrated 8-port 10/100 Ethernet switch for connecting to the LAN



    10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN



    Separate console and auxiliary ports



    (Optional) embedded Wi-Fi certified dual-radio 802.11a/b/g/n-compliant wireless AP



    Optional 4-port PoE

    Note

    The Cisco 890 Series ISRs can include an optional PoE module that provides power to
    802.3af-compliant devices connected to Ethernet ports 0 through 3. If this feature was not
    configured with the factory order, you must order and install it to enable the PoE function.

    Note

    On a Cisco 891 series router, due to TCAM limitation, you can apply an ACL configuration on
    maximum 9 ports. If you apply the ACL configuration beyond 9 ports, the configuration will not
    be applied, and the router will display an error message.

    Note

    Layer 2 FastEthernet ports of Cisco 800 series routers do not support Downloadable
    ACL(dACL). Layer 2 GigabitEthernet ports support downloadable ACL(dACL).



    Security feature card (SFC) socket



    DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
    system memory in Cisco 891 and Cisco 892 ISRs, and a total of 1 GB system memory in
    Cisco 892F series ISRs



    Three reverse-polarity Threaded Neill-Concelman (RP-TNC) connectors on the back panel for
    non-captive dual-band WLAN antenna (wireless models only)



    Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9



    GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only)

    The following feature is located on the front panel of


    Two USB 2.0 ports

    Cisco Integrated Services Router Hardware Installation Guide

    1-114



  • Page 135

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-62 shows the front panel details of the Cisco 890 Series router.
    Front Panel of the Cisco 890 Series ISR

    272367

    Figure 1-62

    1

    1

    2

    2

    LEDs

    USB ports

    Figure 1-63 shows the back panel details of the Cisco 892W router. Non wireless routers do not have
    RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be
    available on your router. However, the feature locations are similar across all Cisco 890 series routers.
    Figure 1-63

    Back Panel of the Cisco 892W Router

    272369

    Chapter 1

    1

    2

    3

    4

    5

    6

    7

    8

    9

    10 11

    1

    Antenna—Dipole swivel antenna attached to
    RP-TNC connectors (wireless models only)

    7

    PoE power connector for optional PoE
    module1

    2

    Backup—Data BRI2 or V.923 port

    8

    Reset button

    3

    Primary WAN port—FE and GE

    9

    Power connector

    Cisco Integrated Services Router Hardware Installation Guide

    1-115



  • Page 136

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    4

    Auxiliary port

    10 Earth ground connection

    5

    Console port

    11 Kensington security slot

    6

    8-port 10/100 Ethernet switch

    1. The Cisco 890 Series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
    to Ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable
    the PoE function.
    2. The Data BRI port is available only on the Cisco 892 Router models.
    3. The V.92 port (not shown) is available only on the Cisco 891 Router models and is located between the console port and the
    Ethernet switch.

    Figure 1-64 shows the location of the SFP port on a Cisco 892FW router.
    Figure 1-64

    SFP Port Location on a Cisco 892FW Router

    Cisco 892F-W

    SFP

    278179

    EN
    S

    1

    1

    2

    SFP port

    2

    SFP LEDs

    Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
    The Cisco 892FSP, Cisco 896VA, Cisco897VA (includes Cisco 897VA, Cisco 897VAM, Cisco 897VAW,
    Cisco 897VAMW), and Cisco 898EA routers have the following features:


    Integrated 8-port 10/100/1000 Gigabit Ethernet switch for connecting to the LAN



    Two 10/100/1000 GE ports for Cisco 892FSP



    One 10/100/1000 GE port for Cisco 896VA, 897VA, and the Cisco 898EA. Either the SFP socket or
    the 10/100/1000 GE port can be active at a given time, but not both.



    Single console and auxiliary ports for configuration and management



    512 MB of on-board memory (upgrade option to 1 GB)



    256 MB flash memory for Cisco 896VA, Cisco 897VA, and Cisco 898EA



    One USB 2.0 port



    Optional internal adapter for inline PoE on four switch ports for IP phones or external wireless
    access points for Cisco 896VA, Cisco 897VA, and Cisco 898EA models only. No PoE support on
    Cisco 892FSP.

    Cisco Integrated Services Router Hardware Installation Guide

    1-116



  • Page 137

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Note

    The Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have
    an SFC socket.

    Note

    To upgrade DRAM memory from 512 MB to 1 GB on the Cisco 892FSP, Cisco 896VA, Cisco 897VA,
    and Cisco 898EA routers, you should enable the FL-8XX-512U1GB license.

    Cisco Integrated Services Router Hardware Installation Guide

    1-117



  • Page 138

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-65 shows the back panel of the Cisco 892FSP Router.
    Figure 1-65

    Back Panel of the Cisco 892FSP Router

    Cisco 892FSP
    CONSOLE

    GE WAN

    GE WAN

    284781

    SFP

    RESET
    8

    9

    AUX

    8

    12VDC

    1

    2

    3

    4

    5

    2.5A

    6

    7

    1

    GE WAN interface

    6

    Power connector

    2

    SFP port

    7

    On/Off switch

    3

    USB port

    8

    Reset button

    4

    8-port Gigabit Ethernet switch

    9

    Earth ground connection

    5

    Console/Auxiliary port

    10 Kensington security slot

    8

    9

    10

    Figure 1-66 shows the front panel of the Cisco 892FSP Router.
    Front Panel of the Cisco 892FSP Router

    284782

    Figure 1-66

    1

    1

    LEDs

    Cisco Integrated Services Router Hardware Installation Guide

    1-118



  • Page 139

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-67 shows the back panel of the Cisco 896VA Router.
    Figure 1-67

    Back Panel of the Cisco 896VA Router

    12
    VDSL/ADSL

    overISDN
    GE WAN

    0

    8

    1

    2

    6

    GELAN 5

    Cisco 896VA

    4

    CONSOLE

    3

    3

    4

    2

    POE

    5

    1

    54VDC
    12VDC

    0

    6

    1

    ISDN

    7

    Power connector

    2

    GE WAN interface

    8

    On/Off switch

    3

    SFP port

    9

    Reset button

    4

    USB port

    7

    344766

    ISDN

    7

    RESET

    1.2A
    2.5A

    8

    9

    10 11

    10 Earth ground connection

    5

    8-port Gigabit Ethernet switch

    6

    Console/Auxiliary port

    1

    11 Kensington security slot
    12 VDSL / ADSL over ISDN

    1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured with
    the factory order, you must order and install it to enable the PoE function.

    Figure 1-68 shows the front panel of the Cisco 896VA and the Cisco 897VA routers.
    Figure 1-68

    Front Panel of the Cisco 896VA and Cisco 897VA Routers

    344765

    Chapter 1

    1

    1

    LEDs

    Cisco Integrated Services Router Hardware Installation Guide

    1-119



  • Page 140

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-69 shows the back panel of the Cisco 897VA Router.
    Figure 1-69

    Back Panel of the Cisco 897VA Router

    12
    VDSL/ADSL

    overPOTS
    GE WAN

    0

    8

    1

    2

    7

    6

    GELAN 5

    Cisco 897VA

    4

    CONSOLE

    3

    3

    2

    4

    POE

    1

    54VDC
    12VDC

    0

    6

    5

    1

    ISDN

    7

    Power connector

    2

    GE WAN interface

    8

    On/Off switch

    3

    SFP port

    9

    Reset button

    4

    USB port

    RESET

    1.2A
    2.5A

    7

    344767

    ISDN

    8

    9

    10 11

    10 Earth ground connection

    5

    8-port Gigabit Ethernet switch

    6

    Console/Auxiliary port

    1

    11 Kensington security slot
    12 VDSL/ADSL over POTS

    1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
    the factory order, you must order and install it to enable the PoE function.

    Figure 1-70 shows the back panel of the Cisco 897VAM Router.
    Figure 1-70

    Back Panel of the Cisco 897VAM Router

    11
    VDSL/ADSL

    overPOTS

    7

    6

    GELAN 5

    4

    8

    1

    3

    2

    3

    POE

    4

    1

    54VDC
    12VDC

    0

    5

    6

    RESET

    1.2A
    2.5A

    7

    1

    GE WAN interface

    7

    On/Off switch

    2

    SFP port

    8

    Reset button

    3

    USB port

    9

    Earth ground connection

    Cisco Integrated Services Router Hardware Installation Guide

    1-120

    2

    344769

    CONSOLE

    GE WAN

    8

    9

    10



  • Page 141

    Product Overview
    Cisco 860, 880, 890 Series

    4

    8-port Gigabit Ethernet switch1

    10 Kensington security slot

    5

    Console / Auxiliary port

    11 VDSL / ADSL over POTS

    6

    Power connector

    1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature was not configured
    with the factory order, you must order and install it to enable the PoE function.

    Figure 1-71 shows the front panel of the Cisco 897VAM router.
    Front Panel of the Cisco 897VAM Router

    344768

    Figure 1-71

    1

    1

    LEDs

    Figure 1-72 shows the back panel of the Cisco 897VAW router.
    Figure 1-72

    Back Panel of the Cisco 897VAW Router

    11
    VDSL/ADSL

    overPOTS

    7

    6

    GELAN 5

    4

    CONSOLE

    GE WAN

    8

    1

    3

    2

    3

    2

    POE

    4

    1

    54VDC
    12VDC

    0

    5

    6

    RESET

    1.2A
    2.5A

    7

    1

    GE WAN interface

    7

    On/Off switch

    2

    SFP port

    8

    Reset button

    3

    USB port

    9

    Earth ground connection

    4

    8-port Gigabit Ethernet switch

    5

    Console / Auxiliary port

    6

    Power connector

    1

    344771

    Chapter 1

    8

    9

    10

    10 Kensington security slot
    11 VDSL / ADSL over POTS

    1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
    the factory order, you must order and install it to enable the PoE function.

    Cisco Integrated Services Router Hardware Installation Guide

    1-121



  • Page 142

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-73 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW routers.
    Front Panel of the Cisco 897VAW and the Cisco 897VAMW Routers

    344770

    Figure 1-73

    1

    1

    LEDs

    Figure 1-74 shows the back panel of the Cisco 897VAMW Router.
    Figure 1-74

    Back Panel of the Cisco 897VAMW Router

    11
    VDSL/ADSL

    overPOTS

    7

    6

    GELAN 5

    4

    8

    1

    3

    2

    3

    2

    POE

    4

    1

    54VDC
    12VDC

    0

    5

    6

    RESET

    1.2A
    2.5A

    7

    1

    GE WAN interface

    7

    On/Off switch

    2

    SFP port

    8

    Reset button

    3

    USB port

    9

    Earth ground connection

    4

    8-port Gigabit Ethernet switch

    5

    Console/Auxiliary port

    6

    Power connector

    1

    344772

    CONSOLE

    GE WAN

    8

    9

    10

    10 Kensington security slot
    11 VDSL / ADSL over POTS

    1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
    the factory order, you must order and install it to enable the PoE function.

    Cisco Integrated Services Router Hardware Installation Guide

    1-122



  • Page 143

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-75 shows the back panel of the Cisco 898EA router.
    Figure 1-75

    Back Panel of the Cisco 898EA Router

    11
    7

    SHDSL

    RJ45 ONLY

    6

    GELAN 5

    Cisco 898EA

    4

    CONSOLE

    GE WAN

    8

    8

    1

    2

    3

    3

    2

    POE

    1

    4

    AUX

    0

    5

    54VDC
    12VDC

    6

    RESET

    1.2A
    2.5A

    7

    1

    GE WAN interface

    7

    On/Off switch

    2

    SFP port

    8

    Reset button

    3

    USB port

    9

    Earth ground connection

    4

    8-port Gigabit Ethernet switch

    5

    Console/Auxiliary port

    6

    Power connector

    1

    344774

    SFP

    8

    9

    10

    10 Kensington security slot
    11 SHDSL (RJ45 only)

    1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured with
    the factory order, you must order and install it to enable the PoE function.

    Caution

    The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
    port may occur if a non-RJ-45 connector is inserted.

    Figure 1-76 shows the front panel of the Cisco 898EA Router.
    Figure 1-76

    Front Panel of the Cisco 898EA Router

    344773

    Chapter 1

    1

    1

    LEDs

    Cisco Integrated Services Router Hardware Installation Guide

    1-123



  • Page 144

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Cisco C897VAB-K9
    The Cisco 897VAB-K9 ISR is designed to support 2-pair VDSL2 bonding up to the 17a profile and single
    pair support for ADSL/VDSL over POTS up to the 30a profile.
    Table 1-41 provides information about important hardware specifications pertaining to Cisco
    C897VAB-K9 ISR.
    Table 1-41

    Hardware Specifications of Cisco C897VAB-K9 ISR

    Hardware

    Description

    Flash Memory

    256 MB

    Main Memory

    1-GB DDR RAM; fixed and not extendable

    USB port

    A USB 2.0-compliant port located on the back
    panel

    FAN

    Fanless chassis

    PoE

    (Optional) Four internal PoE ports

    Primary WAN

    VDSL/ADSL over POTS

    Backup WAN

    10/100/1000 GE port (RJ-45/SFP)

    Console or auxiliary port

    RJ-45

    LAN switch

    8-port 10/100/1000 GE Switch

    Figure 1-77 shows the back panel of the Cisco 897VAB-K9 ISR.
    Figure 1-77

    Back panel of the Cisco 897VAB-K9 ISR

    B

    364228

    ISDN

    over POTS,VDSL

    1

    2

    3

    4

    6

    7

    1

    Primary WAN
    VDSL / ADSL over POTS, 7
    VDSL2 Bonding1

    2

    SFP port

    8

    Power Connector

    3

    GE WAN Interface

    9

    On/Off Switch

    4

    ISDN

    10 Reset Button

    5

    USB Port

    6

    8-port Gigabit Ethernet Switch

    8 9 10

    Console/Auxiliary Port

    11 Earth Ground connection
    2

    Cisco Integrated Services Router Hardware Installation Guide

    1-124

    5

    12 Kensington Security slot

    11 12



  • Page 145

    Product Overview
    Cisco 860, 880, 890 Series

    1. 1.ADSL and VDSL (up to 17a) single-pair functionality uses the center pair of pins in the RJ-11 connector. VDSL 30a single
    pair functionality makes use of the pins just adjacent to the center pins. VDSL Bonding makes use of both the center pair pins
    & those just adjacent to the center pair to provide the 2 bonded VDSL lines. For more information, see Cisco 890 Series
    Integrated Services Routers Data Sheet.
    2. 2.Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured
    with the factory order, you must order and install it to enable the PoE function.

    The primary WAN port is designed for an RJ-11 or RJ-14 connector only. Damage to the
    primary WAN port may occur if a non-RJ-11 or RJ-14 connector is inserted.

    Caution

    Figure 1-78 shows the front panel of the Cisco 897VAB-K9 ISR.
    Figure 1-78

    Front panel of the Cisco 897 VAB-K9 ISR

    4

    2
    1

    3

    5

    ISDN

    CD0 CD1

    6

    B1

    364227

    Chapter 1

    B2

    8
    9

    7

    Table 1-42 describes the LEDs for the Cisco 897VAB-K9 ISR.
    Table 1-42

    LED Descriptions for the Cisco 897VAB-K9 ISR

    Number LED

    Color

    Description

    1

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.

    Power OK

    Blinking—Boot up is in process, or the router is in ROM
    Monitor (ROMMON) mode.
    Off—Power is not supplied to the router.
    2

    PoE OK

    Green/Yellow

    Off—Both POE card & POE power supply are not
    present.
    Yellow On—Either POE card or POE power supply is
    not present.
    Green On—Both POE card & POE power supply are
    present.

    Cisco Integrated Services Router Hardware Installation Guide

    1-125



  • Page 146

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-42

    LED Descriptions for the Cisco 897VAB-K9 ISR (continued)

    Number LED

    Color

    Description

    3

    Green/Yellow

    Off—No link.

    4

    GE LAN 0
    GE LAN 1

    Green On—Link.

    GE LAN 2

    Yellow On—Fault with PoE. Implies no link.

    GE LAN 3

    Green Blinking—Data is either being received or
    transmitted.

    GE LAN 4

    Green

    GE LAN 5

    On—Link.

    GE LAN 6

    Blinking—Data is either being received or being
    transmitted.

    GE LAN 7
    5

    Off—No link.

    GE WAN 8

    Green

    Off—No link.
    On—Link.
    Blinking—Data is either being received or being
    transmitted.

    SFP WAN 8

    Green

    Off—No link.
    On—Link.
    Blinking—Data is either being received or being
    transmitted.

    6

    VPN

    Green

    Off—No tunnel.
    On—At least one tunnel is up.

    7

    PPP

    Green

    Off—No PPP session.
    On—At least one PPP session established.

    8

    xDSL CD0

    Green

    xDSL CD1

    Off—Interface is shutdown.
    On—Showtime, Link up.
    Slow Blinking—Modem initialization.
    Fast Blinking—Training up the line.
    If both CD0 & CD1 are ON then VDSL Bonding is
    active.

    xDSL DATA

    Green

    Off—No Data.
    Blinking—Data is either being received or transmitted.

    9

    ISDN B1

    Green

    ISDN B2

    Cisco Integrated Services Router Hardware Installation Guide

    1-126

    Blinking—Data is either being received or transmitted.
    Off—No Data.



  • Page 147

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Cisco C891 Series ISRs
    Cisco C891 Series ISRs are designed to deliver secure broadband, metro Ethernet, wireless LAN
    (WLAN) connectivity, and business continuity. Cisco C891 Series ISRs also provide a 1-port Gigabit
    Ethernet SFP socket for WAN connectivity.
    This section includes the hardware information for the following models:


    Cisco C891F



    Cisco C891FW

    Table 1-43 provides information about the hardware specifications of the Cisco C891 Series Routers.
    Table 1-43

    Hardware Specifications of Cisco C891 Series ISR

    Hardware

    Description

    Flash Memory

    256 MB

    Main Memory

    1-GB DDR RAM; fixed and not extendable

    USB port

    A USB 2.0-compliant port located on the back
    panel

    FAN

    Fanless chassis

    PoE

    4 PoE ports

    WAN

    1-port GE or 1-port SFP

    Data Backup



    1-port FE



    1-port ISDN



    1-port V.92

    Console or auxiliary port

    RJ-45

    LAN switch

    8-port Gigabit Ethernet

    Embedded Wireless AP

    Dual 802.11b/g/n and 802.11a/n radios for
    C891FW

    For detailed hardware specifications, see the Cisco C890 Series hardware data sheet at:
    http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78-519930.html

    Cisco C891F Router
    Figure 1-79 shows the front panel of the Cisco C891F Router.

    Cisco Integrated Services Router Hardware Installation Guide

    1-127



  • Page 148

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Front Panel of the Cisco C891F Router

    OK

    OK

    0

    POE
    OE

    1

    2

    3

    4

    POE
    OE

    5

    6

    7

    GE8 SFP8 FE0

    WAN
    GE LAN
    ISDN

    VPN PPP

    V.92

    B1

    B2

    Cisco 800 Series

    361136

    Figure 1-79

    1

    1

    LEDs

    For detailed description about the LEDs on the Cisco C890 Series Routers, see the “LEDs” section on
    page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-128



  • Page 149

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Figure 1-80 shows the back panel of the Cisco C891F Router.
    Figure 1-80

    Back Panel of the Cisco C891F Router

    7

    FE WAN
    AN

    GE WAN
    AN

    ISDN

    6

    GE LAN
    AN 5

    Cisco 89
    Ci
    891F

    4

    (POE)

    CON
    ONSOLE
    OLE

    V.92
    .92

    361137

    SFP

    RESET
    RES
    0

    0

    0

    8

    8

    1

    2

    3

    4

    5

    3

    6

    2

    POE

    1

    UX
    AUX

    0

    7

    54VDC
    54V
    12V
    12VDC

    8

    1.5A
    .5A
    3.5-5A

    9

    11

    12 13

    10

    1

    Back up WAN port—FE WAN

    8

    Console/Auxiliary port

    2

    ISDN

    9

    Power connector

    3

    Primary WAN port—GE WAN

    10 On/Off switch

    4

    SFP

    11 Reset button

    5

    USB port

    12

    6

    V.92 backup

    13 Kensington security slot

    7

    8-port 10/100/1000 Ethernet switch

    Earth ground connection

    For information on installing the Cisco C890 Series Routers, see:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco C891FW Router
    Figure 1-81 shows the front panel of the Cisco C891FW Router.
    Front Panel of the Cisco C891FW Router
    OK

    OK

    0

    POE

    1

    2

    3

    4

    POE
    ISDN

    VPN PPP

    V.92

    5

    6

    7

    GE8 SFP8 FE0 2.4GHz 5GHz

    WAN
    GE LAN

    B1

    B2

    Cisco 800 Series

    361138

    Figure 1-81

    1

    1

    LEDs

    For detailed description about the LEDs on Cisco C890 Series Router, see “LEDs” section on page 1-30.

    Cisco Integrated Services Router Hardware Installation Guide

    1-129



  • Page 150

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-82 shows the back panel of the Cisco C891FW Router.
    Figure 1-82

    Back Panel of the Cisco C891FW Router

    7

    FE WAN
    AN

    ISDN

    GE WAN
    AN

    6

    GE LAN
    AN 5

    Cisco 89
    Ci
    891FW
    FW

    4

    CON
    ONSOLE
    OLE

    V.92
    .92

    (POE)

    361139

    SFP

    RESET
    RES
    0

    0

    8

    8

    1

    2

    3

    4

    0

    5

    3

    6

    2

    POE

    1

    UX
    AUX

    0

    7

    8

    54VDC
    54V
    12V
    12VDC

    1.5A
    .5A
    3.5-5A

    9

    11

    12 13

    10

    1

    Back up WAN port—FE

    8

    Serial port—Console or auxiliary

    2

    ISDN

    9

    Power connector

    3

    Primary WAN port—GE

    10 On/Off switch

    4

    SFP port

    11 Reset button

    5

    USB port

    12 Earth ground connection

    6

    V.92 backup port

    13 Kensington security slot

    7

    8-port 10/100/1000 Ethernet switch

    For information on installing the Cisco C890 Series Routers, see:
    http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
    l880-860.html

    Cisco Integrated Services Router Hardware Installation Guide

    1-130



  • Page 151

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Cisco C891-24X/K9 Integrated Services Router
    Cisco C891-24X/K9 Integrated Services Router (ISR) is a fixed Cisco 890 Series ISR that supports 24
    port GE LAN. Cisco C891-24X/K9 ISR provides more switch port options compared to other 890 Series
    ISRs and Cisco C891-24X/K9 ISR is useful in deployment scenarios where more switching capability
    is required. Cisco C891-24X/K9 ISR also supports PoE on 8 switch ports. Cisco C891-24X/K9 ISR
    supports WAN connectivity through dual GE or SFP ports.
    Table 1-44 provides information about important hardware specifications pertaining to Cisco
    C891-24X/K9 ISR.
    Table 1-44

    Hardware Specifications for Cisco C891-24X/K9 ISR

    Hardware

    Description

    Flash Memory

    256 MB Flash and 8 MB serial boot flash

    Main Memory

    1-GB DDR RAM

    USB port

    A USB 2.0-compliant port located at the back
    panel

    PoE

    8 PoE ports

    WAN

    2-port GE WAN (copper or SFP)

    Console or auxiliary port

    RJ-45

    LAN switch

    24-port 10/100/1000 BASE-T

    Fan

    Fan less Chassis

    Figure 1-83 shows the front panel of the Cisco C891-24X/K9 ISR.
    Figure 1-83

    Front Panel of the Cisco C891-24X/K9 ISR

    POWER

    Cisco Integrated Services Router Hardware Installation Guide

    1-131



  • Page 152

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Figure 1-84 shows the back panel of the Cisco C891-24X/K9 ISR.
    Back Panel of the Cisco C891-24X/K9 ISR

    POE Enabled

    Cisco C891-24X

    GE LAN

    SYSTEM

    1

    2

    3

    4

    5

    6

    1

    Console or auxiliary port

    7

    SFP port

    2

    Reset Button

    8

    GE WAN port

    3

    USB port

    9

    SFP port

    4

    PoE enabled GE LAN ports

    10 System LED

    5

    GE LAN ports

    11 Kensington security slot

    6

    GE WAN port

    7

    8

    364240

    Figure 1-84

    9 10 11

    For information on installing the C891-24X/K9 ISR see the following link:
    http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/installin
    g.html

    Hardware Features
    This section provides an overview of the following hardware features for the Cisco 860 Series, 880
    Series, and 890 Series ISRs. A feature summary is available at the end of this section.


    Kensington Lock



    Reset Button



    LEDs



    Memory



    USB Port



    Fan



    Power Supply



    Power over Ethernet Module



    3G Cellular Data WAN Connectivity



    Small Form-Factor Pluggable Port



    Feature Summary

    Cisco Integrated Services Router Hardware Installation Guide

    1-132



  • Page 153

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Kensington Lock
    A Kensington security slot is located on the router back panel. To secure the router to a desktop or other
    surface, use the Kensington lockdown equipment.

    Reset Button
    The Reset button is used to restore the router to the factory default configuration or to load a custom
    configuration file.
    There are two different ways to do this:

    Note



    By pressing the Reset button within 5 seconds of powering up the router.



    By pressing the Reset button for 5 seconds while running IOS software.

    If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified
    Wireless Network software, the router reboots, but the AP continues to run. Clients with Cisco Unified
    Wireless Network software are controlled by a wireless LAN controller (WLC) and can be reset only by
    the controller.

    Cisco 860VAE Routers—Custom Configuration File
    On the Cisco 860VAE routers, the reset button can be used to load a custom configuration file without
    having to use the CLI. The configuration file can be located on an external USB flash drive or on the
    router's compact flash.
    The custom configuration file must be named one of the following:


    customer-config



    SN-customer-config (where “SN” is the unique hardware serial number)

    When the system attempts to load a custom configuration file, configuration files on a USB flash drive
    have priority over configuration files on the router's flash drive and the SN-customer-config file name
    has priority over the customer-config file name. The priority for loading a configuration file is as
    follows:
    1.

    USB flash0—SN-customer-config

    2.

    USB flash0—customer-config

    3.

    Router flash—SN-customer-config

    4.

    Router flash—customer-config

    If the router does not find a valid custom configuration file, the system aborts the process.

    To reset the router to the factory default configuration, follow these steps:
    Step 1

    Verify that Cisco IOS is running correctly by checking that the system status LED is on.

    Cisco Integrated Services Router Hardware Installation Guide

    1-133



  • Page 154

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Step 2

    Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
    5 seconds.
    The router reloads itself after the startup configuration has been replaced with the new customer
    configuration.

    Custom Configuration File for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
    In the first method, the configuration file can be located on the router's compact flash or on the router's
    NVRAM. The custom configuration file must use cfg as the filename extension.
    When the system attempts to load a custom configuration file, configuration files on NVRAM have
    priority over configuration files on the router's compact flash.
    The priority for loading a configuration file is as follows:
    1.

    nvram: *.cfg

    2.

    Router flash: *.cfg

    If the router does not find a valid custom configuration file, the system aborts the process.To reset the
    router to the factory default configuration or to load a custom configuration file, follow these steps:
    Step 1

    Turn the power on.

    Step 2

    Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
    5 seconds.
    The router reloads itself after the startup configuration has been replaced with the new customer
    configuration.

    In the second method, the configuration file can be located on an external USB flash drive or on the
    router's compact flash.
    The custom configuration file must be named one of the following:


    customer-config



    customer-config.SN, where "SN" is the unique hardware serial number.

    When the system attempts to load a custom configuration file, configuration files on a USB flash drive
    have priority over configuration files on the router's flash drive and the "customer-config.SN" file name
    has priority over the customer-config file name.
    The priority for loading a configuration file is as follows:
    1.

    usbflash0:customer-config.SN

    2.

    usbflash0:customer-config

    3.

    Router flash:customer-config.SN

    4.

    Router flash:customer-config

    If the router does not find a valid custom configuration file, the system aborts the process.
    To reset the router to the factory default configuration or to load a custom configuration file, follow these
    steps:
    Step 1

    Verify that Cisco IOS is running correctly by checking that the system status LED is on.

    Cisco Integrated Services Router Hardware Installation Guide

    1-134



  • Page 155

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Step 2

    Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
    5 seconds.
    The router reloads itself after the startup configuration has been replaced with the new customer
    configuration.

    LEDs
    The LEDs are located on the front panel of the router.

    Table 1-45



    Table 1-45 describes the LEDs for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series
    ISRs.



    Table 1-46 lists the LED descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
    Cisco 867VAE-K9 ISRs.



    Table 1-47 lists the LED description for the Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco
    898EA ISRs.



    For a description of LEDs for Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco
    860VAE-POE-W-A-K9 ISRs models, see the “Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9,
    and Cisco 860VAE-POE-W-A-K9 ISRs” section on page 1-50.

    LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs

    LED

    Color

    Description

    860 Series

    880 Series

    890 Series

    Power OK

    Green

    On—DC power is being supplied to the router and the
    Cisco IOS software is running.

    All models All models All models

    Blinking—Bootup is in process, or the router is in
    Rommon monitor mode.
    Off—Power is not supplied to the router.
    Link Status FE0

    Green

    Link Status FE1

    All models All models All models

    On—Ethernet port is connected.

    Link Status FE2

    Blinking—Data is either being received or being
    transmitted.

    Link Status FE3

    Off—Ethernet port is not connected.

    Link Status FE4

    Green

    Link Status FE5

    On—Ethernet port is connected.

    Link Status FE6

    Blinking—Data is either being received or being
    transmitted.

    Link Status FE7

    Off—Ethernet port is not connected.

    FE WAN Port
    Link Status

    Green

    On—Port is connected.
    Blinking—Data is either being received or being
    transmitted.





    All models

    861
    models

    881
    models

    All models





    All models

    Off—Port is not connected.
    GE WAN Port
    Link Status

    Green

    On—Port is connected.
    Blinking—Data is either being received or being
    transmitted.
    Off—Port is not connected.

    Cisco Integrated Services Router Hardware Installation Guide

    1-135



  • Page 156

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-45

    LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

    LED

    Color

    WLAN
    (2.4 GHz)

    Green

    Description

    860 Series

    880 Series

    890 Series

    Wireless
    models

    Wireless
    models

    Wireless
    models

    Wireless
    models

    Wireless
    models

    Wireless
    models

    Wireless
    models

    Wireless
    models



    Models
    with PoE

    Models
    with PoE



    All models All models



    All models All models



    886,
    886VA,
    887,
    887VA,
    887VA-M
    888
    models

    1

    On—Radio is connected, SSID is configured, and client Wireless
    models
    is associated, but no data is being received or being
    transmitted.
    Slow blinking—Radio is connected, SSID is configured,
    and beacons are being transmitted.
    Fast blinking—Data is either being received or being
    transmitted.
    Off—Radio is shut down, and no SSID is configured.

    WLAN (5 GHz)

    Green

    On—Radio is connected, SSID is configured, and client is —
    associated, but no data is being received or being
    transmitted.
    Slow blinking—Radio is connected, SSID is configured,
    and beacons are being transmitted.
    Fast blinking—Data is either being received or being
    transmitted.
    Off—Radio is shut down, and no SSID is configured.

    WLAN LINK
    (Autonomous
    Mode)

    Green

    On—Wireless link is up.
    Blinking—Ethernet link is up, and data is either being
    received or being transmitted.

    Wireless
    models

    Off—Wireless link is down.
    WLAN LINK
    (Unified Mode)

    Green

    On—Ethernet link is up, and wireless access point (AP) is —
    communicating with LWAPP2 controller.
    Blinking—Ethernet link is up, but wireless AP is not
    communicating with LWAPP controller.
    Off—Ethernet link is down.

    PoE

    Green

    On—PoE is connected and powered.
    Off—PoE is not installed.

    VPN
    PPP

    3
    4

    xDSL CD

    Amber

    On—Fault with the PoE.

    Green

    On—VPN is connected.

    Green

    On—At least one PPP session is established.

    Green

    5

    On—The xDSL interface is connected to the DSLAM .
    Blinking—Training to the line.
    Off—Indicates that a connection has not been established
    or the port is shut down.

    Cisco Integrated Services Router Hardware Installation Guide

    1-136

    896VA,
    897VA,
    898EA,
    897VAB



  • Page 157

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-45

    LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

    LED

    Color

    Description

    860 Series

    880 Series

    890 Series

    xDSL Data

    Green

    Blinking—The xDSL interface is either receiving or
    transmitting data.



    886,
    886VA,
    887,
    887VA,
    887VA-M
    888
    models

    896VA,
    897VA,
    898EA,
    897VAB



    888E







    898EA

    Off—No data is being transmitted or being received.

    xDSL ATM

    Green

    On—The router is operating in ATM6 mode.
    Off—Not operating in ATM mode.

    xDSL EFM

    Green

    Blink—The router is operating in EFM7 mode.
    Off—Not operating in EFM mode.

    Data BRI LINK

    Green

    On—ISDN D channel is connected.



    887, 888
    models

    892
    models

    Data BRI B1

    Green

    Blinking—B1 channel is either receiving or sending data, —
    or data is passing through ISDN channel 1.

    887, 888
    models

    892
    models

    Data BRI B2

    Green

    Blinking—B2 channel is receiving or sending data, or
    data is passing through ISDN channel 2.



    887, 887V, 892
    888
    models
    models

    3G8 WWAN9

    Green

    On—Service is established.



    3G models —



    3G models —

    Slow Blinking—Searching for service.
    Fast Blinking—Data is either being received or being
    transmitted.
    3G RSSI10

    Green

    Off—Low signal strength (lower than -100 dBm).
    On—High RSSI (-69 dBm or higher).
    Slow Blinking—Low or medium RSSI (-99 to -90 dBm).
    Fast Blinking—Medium RSSI (-89 to -70 dBm).

    3G GSM

    11

    Amber

    On—No service.



    3G models —

    Green

    On—Service is established.



    3G models —



    3G models —



    88113



    Off—No service.
    3G CDMA12

    Green

    On—Service is established.
    Off—No service.

    FXO Voice

    Green

    On—FXO port is connected.
    Blinking—FXO port is either receiving or transmitting
    data.

    BRI Voice LNK

    Green

    On—BRI interface is connected.







    BRI Voice B1

    Green

    On—BRI B1 channel is connected.







    Blinking—BRI B1 channel is either receiving or
    transmitting data.

    Cisco Integrated Services Router Hardware Installation Guide

    1-137



  • Page 158

    Chapter 1

    Product Overview

    Cisco 860, 880, 890 Series

    Table 1-45

    LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

    LED

    Color

    Description

    860 Series

    880 Series

    890 Series

    BRI Voice B2

    Green

    On—BRI B2 channel is connected.









    SRST
    models







    891
    models
    892F
    models

    Blinking—BRI B2 channel is either receiving or
    transmitting data.
    FXS/DID Voice

    Green

    On—FXS/DID port is connected.
    Blinking—FXS/DID port is either receiving or
    transmitting data.

    V.92 Modem

    Green

    On—Modem is connected.
    Blinking—V.92 port is either receiving or transmitting
    data.

    SFP14 EN

    SFP S

    Off

    Not present.





    Green

    Present and enabled.





    Amber

    Present with failure.





    Green

    Blinking—Blinking frequency indicates port speed.





    892F
    models

    1. SSID = service set identifier.
    2. LWAPP = Lightweight Access Point Protocol.
    3. PPP = Point-to-Point Protocol.
    4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital
    subscriber line).
    5. DSLAM = digital subscriber line access multiplexer.
    6. ATM = Asynchronous Transfer Mode.
    7. EFM = Ethernet in the First Mile.
    8. 3G = Third-Generation.
    9. WWAN = wireless WAN.
    10. RSSI = Received Signal Strength Indicator.
    11. GSM = Global System for Mobile Communication.
    12. CDMA = code division multiple access.
    13. SRST = Survivable Remote Site Telephony.
    14. SFP = small-form-factor pluggable.

    Table 1-46 describes the LEDs for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco
    867VAE-K9 ISRs.

    Cisco Integrated Services Router Hardware Installation Guide

    1-138



  • Page 159

    Chapter 1

    Product Overview
    Cisco 860, 880, 890 Series

    Table 1-46

    LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs

    LED

    Activity

    Description

    Power/System

    Power/System LED: Solid Power is on and system running in the ROMMON mode.
    GE_MODE LED: Off
    Note
    During the early booting stage, both Power/System, GE_MODE, and
    DSL_LINK LED: Off
    DSL_LINK LED will be turned on temporarily for the power on test.
    DSL_LINK and GE_MODE LED will be turned off later after booting
    into ROMMON.
    Power/System LED: Solid Cisco IOS functioning in GE WAN mode.
    GE_MODE LED: Solid
    DSL_LINK LED: Off
    Power/System LED: Solid Cisco IOS functioning in DSL_WAN mode.
    GE_MODE LED: Off
    Note
    In Cisco IOS DSL_WAN mode, DSL_LINK LED will be solid after
    DSL_LINK LED: Solid or
    DSL training complete or flashing during training.
    flashing

    xDSL1 ACT

    Green

    On—DSL interface is up.
    Blinking—DSL WAN activity (traffic in either direction).
    Faster blinking—Heavier traffic
    Off—Device is powered off or the DSL WAN interface is down.

    xDSL Link

    Green

    On—DSL WAN Mode is selected and DSL training complete.
    Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state,
    such as in-training, or controller “OFF,” or no cable attached to DSL connector.
    Off—Device is powered off or GE WAN mode is selected.

    GE ACT

    Green

    On—GE WAN interface is up.
    Blinking—GE WAN activity (traffic in either direction).
    Off—Device is powered off or GE WAN interface is down.

    GE Mode

    Green

    On—GE WAN Mode is selected.
    Off—Device is powered off or DSL WAN mode is selected.

    1. xDSL = General term referring to various forms of DSL, includi\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
    ng ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line).

    Cisco Integrated Services Router Hardware Installation Guide

    1-139