650695
5
Zoom out
Zoom in
Vorherige Seite
1/136
Nächste Seite
Getting Started
Feature Overview
Cisco SPA100 Series Administration Guide 5
1
You can keep the default settings or configure these tones in the Call Progress Tones
section of the Regional page.
Call Progress Tone Pass Through
This feature allows the user to hear the call progress tones (such as ringing) that are
generated from the far-end network.
Echo Cancellation
Impedance mismatch between the telephone and the IP Telephony gateway phone port
can lead to near-end echo. The ATA has a near-end echo canceller that compensates for
impedance mismatch. The ATA also implements an echo suppressor with Comfort
Noise Generator (CNG) so that any residual echo is not noticeable. This feature is
enabled by default. You can configure this setting in the Audio Configuration of the
Line 1 and Line 2 Settings (PHONE 1 and PHONE 2) page.
Hook Flash Events
The ATA can signal hook flash events to the proxy during a connected call. This
feature can be used to provide advanced mid-call services with third-party-call control.
- Depending on the features that the service provider offers using third-party-call-
control, you may need to disable Call Waiting Service, Three Way Conference
Service, or Three Way Call Service to correctly signal a hook flash event to the
softswitch. You can configure these settings in the Supplementary Service
Subscription section of the Line 1 and Line 2 Settings (PHONE 1 and PHONE 2)
page.
- You can configure the length of time allowed for detection of a hook flash by
adjusting the Hook Flash Timer parameter in the Control Timer Values section of
the SIP page.
Configurable Dial Plan with Interdigit Timers
The ATA has three configurable interdigit timers: an initial timeout signaling that a
phone is taken off hook, a long timeout signaling the end of a dialed string, and a short
timeout, signaling that more digits are expected. For more information, see
Configuring Dial Plans, page 138.
Polarity Control
The ATA allows the polarity to be set when a call is connected and when a call is
disconnected. This feature is required to support some pay phone system and
answering machines. You can configure these settings in the FXS Port Polarity
Configuration section of the Line 1 and Line 2 Settings (PHONE 1 and PHONE 2)
page.
Calling Party Control
Calling Party Control (CPC) signals to the called party equipment that the calling party
has hung up during a connected call by momentarily removing the voltage between the
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cisco Cisco SPA112 VoIP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info