Bedienungsanleitung Cisco WRT120N (Seite 5 von 55) (Englisch)

475373

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Chapter 1

Product Overview

Wireless-N Home Router

Chapter 1:

Product Overview

Thank you for choosing the Linksys by Cisco Wireless-N

Home Router. The Router lets you access the Internet via

a wireless connection or through one of its four switched

ports. You can also use the Router to share resources

such as computers, printers and files. A variety of security

features help to protect your data and your privacy

while you are online. Security features include WPA2

security, a Stateful Packet Inspection (SPI) firewall, and

NAT technology. Configuring the Router is easy using the

provided browser–based utility.

Front Panel

1, 2, 3, 4 (Blue) These numbered LEDs,

corresponding with the numbered ports on the

Router’s back panel, serve two purposes. If the

LED is continuously lit, the Router is successfully

connected to a device through that port. A

flashing LED indicates network activity over

that port.

Wi-Fi Protected Setup Button If you have

client devices, such as wireless adapters, that

support Wi-Fi Protected Setup, then you can

use Wi-Fi Protected Setup to automatically

configure wireless security for your wireless

network.

To use Wi-Fi Protected Setup, run the Setup

Wizard, or refer to Wi-Fi Protected Setup, page

11.

Wi-Fi Protected Setup LED (Blue/

Amber) The LED lights up blue when wireless

security is enabled. It flashes blue for two

minutes during Wi-Fi Protected Setup.

The LED lights up amber if there is an error

during the Wi-Fi Protected Setup process. Make

sure the client device supports Wi-Fi Protected

Setup. Wait until the LED is off, and then try again.

The LED flashes when a Wi-Fi Protected Setup

session is active. The Router supports one

session at a time. Wait until the LED is solidly lit,

or off before starting the next Wi-Fi Protected

Setup session.

Wireless (Blue) The Wireless LED lights up

when the wireless feature is enabled. If the LED

is flashing, the Router is sending or receiving

data over the network.

Internet (Blue) The Internet LED lights up

when there is a connection made through the

Internet port. It flashes to indicate network

activity over the Internet port.

Power (Blue) The Power LED lights up and will

stay on while the Router is powered on. When

the Router goes through its self-diagnostic

mode during every boot-up, this LED will flash.

When the diagnostic is complete, the LED will

be solidly lit.

Back Panel

Internet The Internet port is where you will

connect your cable or DSL Internet connection.

4, 3, 2, 1 These Ethernet ports (4, 3, 2, 1)

connect the Router to computers on your wired

network and other Ethernet network devices.

Reset The Reset button is located on the

right side of the product label. There are two

ways to reset the Router to its factory defaults.

Either press and hold the Reset button for

approximately five seconds, or restore the

defaults from the Administration > Factory

Defaults screen of the Router’s browser-based

utility.

Power The Power port connects to the included

power adapter.

Horizontal Placement

The Router has four rubber feet on its bottom panel. Place

the Router on a level surface near an electrical outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cisco WRT120N Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info