Bedienungsanleitung Citronic CM10-LIVE (Seite 3 von 5) (Englisch)

455910

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Rear Panel

Connection

Before connecting to amplifier or other equipment, turn down all volume controls to avoid loud noises which may

cause damage to other equipment. Always switch amplifier power on last in line with volume levels down.

Using good quality 6.3mm jack leads (balanced or unbalanced), connect L + R outputs from the mixer to the

amplifier, recorder or whichever equipment is to receive the main mix output.

If phantom power is to be used, press the “+48V” switch in.

Connect microphones, DI boxes and other balanced low impedance audio inputs to the mono channels using a

quality XLR lead.

Connect high impedance and line level signals to the mono inputs using a 6.3mm jack lead.

For the stereo channel, connect left and right line level signals via 6.3mm jack or RCA leads (unbalanced).

Channel inserts may be connected to individual processing equipment like EQ or compressors. These connections

completely interrupt the signal flow and divert to the external processor before returning to the channel for volume

adjustment via the channel fader. This requires a stereo to 2 x mono jack lead – the 2 mono ends are send and

return connections, the stereo connection is wired as per below.

Recording equipment can be connected via the “REC” outputs using a twin RCA lead and the 6.3mm jack AUX

output can be connected to monitoring or external processing equipment if required. Individual levels can be

adjusted to the AUX output via the individual channel AUX controls.

For CM-LIVE models, if the internal delay effect is not required, a send can be connected from the “EFFECT” jack

output to and external effect unit, whereby the EFF channel controls act as individual level controls to the EFFECT

output (same as for AUX output)

With all faders down, connect the supplied AC adapter to the 12Vac input and to the mains supply (ensure correct

supply voltage) – the power LED will illuminate (if phantom power is selected, this LED should light also)

Checking

Test each channel’s gain level by making the loudest expected sound into it and increasing the GAIN control until

the red PEAK LED starts to light. Then back the GAIN off slightly until the PEAK LED hardly lights at all.

Test the main mix output by increasing the MAIN fader and selected channel faders whilst making sound through

the channel(s) – the L + R output LED ladders should begin to show the output as it varies up and down.

Connecting a pair of headphones to the PHONES stereo 6.3mm jack is a good way of checking the mix output,

remembering to gradually increase the PHONES level control.

Turn down all faders and then switch power on to connected equipment (amplifier last in line) and increase volume

levels. Gradually increase MAIN and channel faders again and the sound should be heard through the speakers or

be indicated on the recording equipment.

27. 12Vac power input (adapter supplied)

28. USB type B – output/monitoring input (CM-STUDIO only)

29. L + R main output (on top control panel for CM-STUDIO)

30. SD card slot (CM-LIVE only)

31. USB type A input (CM-LIVE only)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic CM10-LIVE Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info