Bedienungsanleitung Citronic PD-1s mk2 (Seite 5 von 10) (Englisch)

34402

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Citronic Limited User manual

Page 5 of 10

Check List

lCheck that the following parts are included in the

package with the main unit:

1) Turntable platter

2) Slip mat

3) Dust cover

4) 45-rpm adapter

5) Counterweight

6) Operating instructions

7) Phono lead

Assembly Instructions

1. Remove the main unit with the packing from the

box and take off the packing.

2. Insert the 45-rpm adaptor in the slot on the

turntable.

3. Place the turntable platter onto the center

spindle.

4. Place the slip mat on the platter.

5. Installation of cartridge:

When installing a cartridge, refer to the operating

instructions of that cartridge.

During installation, attach the stylus protector to

guard the stylus tip from damage.

6. Insert the headshell into the front end of the

tonearm, then turn the lock nut clockwise with the

headshell firmly held horizontally.

7. Slide counterweight onto tonearm.

Twist it lightly and it will screw onto the rear shaft

of the tonearm.

8. Adjustment of horizontal zero (0) balance and

stylus pressure:

(a) Remove the stylus protector, do not touch

the stylus tip during the adjustment.

(b) Set the cueing lever to the lower position.

from the arm rest to free it.

(d) While holding the Headshell lever rotate the

counterweight until the tonearm is approximately

balanced horizontally (floats freely).

(e) Refasten the tonearm with the arm clamp.

(f) Hold the counterweight stationary with one

hand and rotate only the stylus-pressure ring to

bring the number "0" of the ring into alignment

with the center line on the tonearm rear shaft.

(g) Rotate the counterweight clockwise until the

scale shows the value corresponding to the

pressure of the used stylus, typically 4 grams.

9. Set the anti-skating control knob to the same

value as the stylus pressure.

10. Install the dust cover to the main unit.

Placement

lDo not place the unit in a location where it will be

exposed to direct sunlight or near a heating

appliance.

lDo not place the unit in a location where there is

high humidity or a lot of dust.

lCartridge may pick up sound pressures or vibrations

from the speakers coming along the floor or through

the air resulting in howling. Find a location, which is

very stable, and vibration free.

lThe legs have functions for adjusting the height of

the unit itself. Adjust the legs to stabilize the main

body horizontally.

Connections

1. Connect the power cord to the household AC

outlet.

2. Connect the unit output terminals to the PHONO

inputs of your mixer.

Output terminals Mixer input

L White) >> L Channel

R (Red) >> R Channel

GND (Spade) >> GND

NOTE: Be sure to connect the separate ground

terminal firmly to the Mixer.

If this connection is not made or is loose, a

power source "HUM" will result.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic PD-1s mk2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info