Bedienungsanleitung Citronic Z5M (Seite 3 von 3) (Englisch)

455913

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Applications

The Z5M can be used for any multi-output setup and is ideally suited to controlling a multi-room zoning sound system with up to 5 stereo or

mono zones. Individual zones can be selected as mono if speaker placement is not conducive to stereo imaging. 2 separate stereo inputs can be

selected or blended at will for each zone, opening up the possibility of separate program material for specific zones. Prior to rack-mounting the

unit, it is important to know what the mains supply voltage will be, since the voltage selector is situated on the side panel towards the rear of the

unit.

Connection

All connections are via balanced XLR and operate at line level. Use good quality XLR signal leads to connect the source signals to LINE 1 and

LINE 2 inputs. Each output should be connected to the respective amplifier or active speakers for the particular zone, again using good quality

XLR signal leads. Connect mains using the supplied IEC lead.

Operation

Set amplifier and active speaker volume levels fully down

Set LINE 1 and LINE 2 levels for each zone to “MIN”

Select MONO for any zones that are better suited to mono output.

Press the POWER switch on and play the signals connected to LINE 1 and LINE 2 inputs.

The LINE SIGNAL LEDs should indicate the presence of each input signal.

Gradually increase and then decrease the volume for LINE1 and LINE 2 to each zone in turn to check the output.

Set the volumes and adjust for each source to each zone as required.

Before powering the Z5M down, turn down amplifier and active speaker volumes to avoid loud noises through the speakers.

SPECIFICATIONS

Item

Value

Power supply

115/230Vac 50/60Hz - selectable (IEC)

Inputs

Line 1 L+R, Line 2 L+R, balanced XLRF

Outputs

Zone 1 to 5 L+R, balanced XLRM

Input impedance

40kohms

Output impedance

220ohms

Frequency response

20Hz - 25kHz, +0/-1dB

Signal to noise ratio

>100dB

THD

<0.005%

Dimensions

483 x 175 x 44mm

Weight

2.2kg

TROUBLESHOOTING

No function and Power switch LED is not lit

Ensure mains voltage is correct (check selector) and connected properly

Ensure front panel power switch and mains outlet switch are on

Power is on but no audio output

Check all XLR leads are OK and connected properly

Check that LINE 1 and LINE 2 controls are not all turned fully down

Check that inputs and outputs are connected the correct way around

Distorted output

Reduce LINE 1 and LINE 2 level controls, increasing amp level to compensate

Reduce level of source signal(s) connected to LINE 1 and LINE 2 inputs

Ensure correct line level is selected on amplifier/active speaker inputs

Output is very low level

Ensure input source is line level (0.775Vrms)

Increase LINE 1 and/or LINE 2 level controls,

Increase signal source level

Note: for further troubleshooting, refer equipment to qualified service personnel for testing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic Z5M Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info