Bedienungsanleitung Cleanmaxx Z 04989 - JJ-SC-009D (Seite 27 von 60) (Deutsch, Englisch, Holländisch, Französisch)

562304

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

❐ Danger of scalding! After you switch off the device, hot steam may continue to emerge for a

few seconds! Be careful!

❐ Always switch off the device and pull the mains plug from the plug socket before you remove

the ﬂ oor cleaning cloth or change the nozzle. Always pull the plug and never the cable!

❐ Danger of scalding! The ﬂ oor cleaning cloth / carpet glider / nozzle may be very hot during and

shortly after use. You should therefore wait for a few minutes until the cloth / glider / nozzle has

cooled down completely before you remove it.

❐ Beware of material damage! Very cold glass surfaces (windows in winter) must not be cleaned

with the device.

❐ Before using the device, always check the ﬂ oor cleaning cloth and the carpet glider for signs of

wear. Do not use them if they have visible signs of wear or are damaged. Your ﬂ ooring could

be damaged.

❐ Use the device only if it is in good working order and has been fully assembled and the ﬂ oor

cleaning cloth has been attached for cleaning ﬂ oors.

❐ Never direct the steam on one spot for longer than around 10 seconds without interruption.

This may damage the surface.

Cleaning the Floor

We recommend that, before using the device, you sweep the ﬂ oor with a broom or

vacuum it using a vacuum cleaner.

1. Attach the handle rod with the handle and the cleaning foot to the main unit. Attach to the

cleaning foot the ﬂ oor cleaning cloth and, if you want to clean a carpet, the carpet glider (see

the "Assembling the Device" chapter).

2. Fill the water reservoir (see the "Filling the Water Reservoir" chapter).

3. To unwind the mains cable, turn the upper hook for winding up the cable downwards. Hook the

mains cable into the cable holder so that you can handle the steam mop more easily and do not

trip over the cable while cleaning the ﬂ oor.

4. Place the device in an upright position. The joint of the cleaning foot locks in place in a vertical

position.

5. Insert the mains plug into a properly installed mains socket that is easily accessible.

6. Switch on the device by pressing the On/Off switch. The control lamp on the On/Off switch

lights up red as soon as the device starts the heating-up process. Wait until the device has

reached operating temperature and the control lamp lights up blue. You can now start cleaning

the ﬂ oor.

7. Hold the device by the handle and lower it gently towards the ﬂ oor to release the locked

standing position.

8. Slide the cleaning foot slowly back and forth over the ﬂ oor. The ﬂ oor is cleaned as you do this.

9. If during use no steam or only a small amount of steam is generated, check whether there is

sufﬁ cient water in the water reservoir and top it up again. Before you top up the reservoir,

press the On/Off button, pull the mains plug out of the plug socket and then top up the water

reservoir in the manner described in the "Filling the Water Reservoir" chapter. Then carry on

cleaning the ﬂ oor.

10. Once you have ﬁ nished cleaning the ﬂ oor, press the On/Off switch and pull the mains plug out

of the plug socket. Always pull the plug and never the cable!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cleanmaxx Z 04989 - JJ-SC-009D Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info