Bedienungsanleitung Cleanmaxx Z 06456 - HS101U (Seite 24 von 52) (Deutsch, Englisch, Holländisch, Französisch)

646307

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

EN 24

Use

CAUTION!

• Never aim steam directly at people, animals or plants. This can cause severe scald-

ing.

• Only ever hold the device by the handle and not by the attachment while operating

the device as it can become very hot. There is a danger of scalding!

• Always work with sufﬁ cient lighting.

• Make sure that you do not trip over the mains cable while using the device.

• Never use the device without water!

• Never use the device on cold glass surfaces or at outside temperatures of below

10 °C. The hot steam could cause the glass to shatter.

• Always try cleaning ﬁ rst at a small, inconspicuous spot.

• Never direct the steam at one spot for too long.

• The water reservoir must not be opened during use!

• The device has a a safeguard

(13)

which blocks the steam trigger

(15) so

that it cannot be pressed accidentally. To (de)activate the safeguard, push in

the securing pin.

• Water may emerge from the attachment when you ﬁ rst start using it. This is

normal and does not constitute a defect with the device.

• As the pipe in the device has to ﬁ ll with steam, you may need to press the

steam trigger

(16)

several times when you start using it before steam starts

emerging.

• How much steam is emitted depends mainly on the speed and frequency

with which the steam trigger

(15)

is pressed. The faster you press it, the more

steam is emitted. However, this is at the expense of the temperature.

1. Attach the attachment you want to the device (see the "Mounting the Accessories"

chapter) and ﬁ ll the water reservoir

(18)

(see the "Filling the Water Reservoir" chapter).

2. Insert the mains plug into a properly installed mains socket that is easily accessible.

team starts to be generated and the

control lamp

(17)

lights up.

3. Wait until the control lamp goes out. Operating temperature has then been reached

and you can start steam-cleaning: Press the steam trigger

(15) and move the attach-

ment over the

surface to be cleaned as you do so.

If the steam trigger cannot be pressed, the safeguard

(13)

has probably been

activated. Push in the securing pin to release the safeguard.

4. If the control lamp lights up, the temperature has dropped. Let go of the steam trigger

and only press it again once the control lamp has gone out.

5. If the water reservoir is empty, steam will no longer be produced. If you want to top

up the water in the reservoir (see the "Filling the Water Reservoir" chapter) or want to

stop working, pull the mains plug out of the plug socket and allow the device to cool

down completely. Keep pressing the steam trigger if necessary until no more steam

emerges from the device. The water reservoir can then be opened.

6. Empty and clean the water reservoir each time after you use the device (see

below) to prevent deposits in the reservoir and thus damage to the device!

06456_de-en-fr-nl_V1.indb 2406456_de-en-fr-nl_V1.indb 24 03.07.2015 10:28:0403.07.2015 10:28:04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cleanmaxx Z 06456 - HS101U Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info