Bedienungsanleitung Clifford Concept 50 (Seite 23 von 23) (Englisch)

468917

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

EXAMPLE 1: Turn off siren sound number 2:

1. Look for the siren’s sound number 2 location on the Matrix.

2. The location is at the intersection of column 1 and row 2. Note the column and row

numbers.

3. With the ignition on, enter you disarming code on the PlainView valet switch, then hold

the switch in its momentary position until you hear a chirp and see the LED turn on.

4. Select feature column 1 by pressing the switch to its latched position, then back to

center. After a brief pause, you’ll hear 1 chirp to indicate column 1.

5. Press and release the momentary side twice. You’ll hear a total of two chirps to

indicate that you selected the feature in row 2 of that column.

6. After a brief pause, you’ll hear a single chirp to indicate that sound #2 is now off.

7. Turn the ignition off (you’ll hear 3 chirps) and you’re done!

If you wish to turn siren sound 2 back on, simply repeat steps 1–7.

EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps:

This time, we will change the settings of three different features. This time, you’ll hear

the appropriate chirp confirmations, but we won’t make note of them in the instructions

below:

1. Enter program mode (step 3 above).

2. Latched, center to select column 1.

3. Four momentaries, (wait for the one-chirp “feature off” confirmation), then 6

momentaries to jump to row number 6.

4. Four latched-center presses to select column 4.

5. One momentary, (wait for the two-chirp “feature on” confirmation), then turn the

ignition off and you’re done.

You just changed the settings of three different features. It’s so easy, you could even do it

while driving. To set all three features back to their factory settings, just repeat steps 1-5.

Adding new remote controls

For other drivers in your family or if you wish to control Concept systems on your other

cars with the same remote control, you can buy additional remote controls from any

Authorized Clifford Dealer (or call our 24-hour Customer Service Department at

800-824-3208) and program them into the system yourself. Each Concept 50 will respond

to as many as four 12-channel remote controls. To add a new remote control to the

system, use the procedures noted in the

User-selectable features

section on pages 19–21.

How to erase the codes of lost or stolen remote controls

If one of your remote controls is ever lost or stolen, you can erase its digital codes from

the system memory to make sure that the missing remote control can never be used to

disarm your system. To do so, use the “Erase all channels” feature (feature column 2,

row 6 on the Matrix of user-selectable features on pages 20–21). This will clear all

remote control codes from the system memory. Then simply program each remaining

and/or replacement remote control as noted in the Adding new remote controls section

above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clifford Concept 50 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info