Bedienungsanleitung Cosatto Giggle 2 (Seite 4 von 31) (Englisch, Spanisch)

768916

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

list of parts

Your pushchair is supplied in one carton. Some parts are packed in the carrycot.

1. Pushchair chassis 6. Carrycot with hood 11. Footmuff

2. Rear wheels x2 7. Carrycot apron 12. Seat unit

3. Front wheel assembly 8. Carrycot carry handle 13. Changing bag

4. Carrycot mattress 9. Seat unit hood 14. Raincover

5. Carrycot liner 10. Bumper bar with cover 15. Car seat mounting adaptors

1 - opening the chassis

Press the buttons (a) on either side of the chassis and push the handle down (b). Release the

locking lever (c) and lift the handle upwards until the chassis locks in the open position (d).

WARNING: Ensure that all locking devices are engaged before use.

The height of the handle can be adjusted by pressing the buttons (e) on either side of the chassis

and lifting the handle up (f) or down (g) to the preferred position.

2 - fitting the front wheel assembly

To fit the front wheel assembly insert the pin at the top of the wheel assembly into the wheel

housing (a) until it locks in place.

To remove the wheel assembly, pull back the lever located at the back of the wheel housing (b) and

remove the wheel assembly from the housing.

3 - fitting the rear wheels

To fit a rear wheel insert the pin into the wheel housing (a) until it locks in place. Repeat this with the

other rear wheel.

To remove the rear wheels, press the buttons on top of the wheel housings (b) and pull the wheels

clear (c).

4 - using the parking brake

To apply the brake, press the lever down firmly with your toe (a). Test the brake is engaged

correctly by trying to push the pushchair forwards for a short distance. To release the brake, lift the

lever (b).

NOTE: Always apply brake before loading or unloading a child from the pushchair.

5 - using the swivel wheel lock

Press down on the lever (a). Swivel the wheel until it locks in the forward facing position (b).

Lift the lever (c) to release the lock.

6 - removing the basket

Undo the press studs at the back on the inside of the basket (a) and on the outside at the bottom of

the basket (b). Release the clips (c) at the front of the basket.

Re-fitting is a reversal of this procedure.

7 - folding the chassis

While pressing the release button (a), pull the two levers (b) back. Press down on the handle (c)

closing the chassis until the autocatch retains the chassis in the folded position (d).

The handle position is adjustable and can be folded inwards (e) to achieve the most compact fold.

Whilst pressing on both buttons on both sides of handle, adjust the handle position move the

handle up or down and let go at desired hand position.

Note: The chassis cannot be folded with the carrycot installed and can only be folded with the seat

unit installed forward facing in the most upright recline position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cosatto Giggle 2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info