Bedienungsanleitung Creda W120VW (Seite 2 von 16) (Englisch)

498196

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Positioning & Adjusting the feet

Choosing the position of your appliance will influence its performance.

★ Position where possible on a solid floor. Some vibration may occur with a wooden floor.

★ Take care with vinyl floor coverings.The weight of the appliance may cause indentations in

some vinyl floor coverings.

★ For your safety and to comply with IEE regulations, you should not install your appliance in

a bath or shower room. Seek professional advice if you wish to do so.

★ Ensure sufficient space is allowed for the appliance. Dimensions should be a minimum of:-

600mm Wide (23

”), 600mm Deep (23

”) and 900mm High (35

”).

★ Ensure the electrical socket and water taps are easily accessible and that the water supply

can be isolated if necessary.

Your appliance may become noisy or move about the floor if it is not stabilised.

To adjust your appliance it must be in an upright position, then :-

★ Release locking rings on the two front feet.

★ Screw feet in or out until the appliance is standing firm and level.

★ Ensure all feet are in firm contact with the floor.

★ Tighten the locking rings on the front feet.

Dear Customer,

Congratulations on the purchase of your

new ‘Creda’ appliance.

We recommend for your own safety and to

get the best possible results from your

machine that you read through this

handbook thoroughly before using your

appliance for the first time.

★ Transit Brackets MUST be removed

before using the appliance.

★ DO NOT plug in and switch on at the

mains until installation is complete.

Recycling & Disposal Information

As part of Creda’s continued commitment to helping the environ-

ment, Creda may use quality recycled components to keep down

customer costs and minimise material wastage. Please dispose of

packaging and old appliances carefully.To minimise risk of injury to

children, remove the door,plug and cut mains cable off flush with the

appliance. Dispose of seperately to ensure that the appliance can no

longer be plugged into a mains socket.

Electrical Requirements

This appliance should be connected to the mains supply via a suitable switched socket in an

accessible position.

WARNING: This appliance must be earthed.

FUSES

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only

those rated at 13A and ASTA approved to BS1362 should be used.To change fuse, lift holder

to vertical position and lift fuse out.To replace, insert fuse and push fuse holder down into

locked position.Correct replacement is identified by colour coding, or marking on base of

plug.

WARNING: Do not use plug unless fuse holder is in locked position.

CHANGING THE PLUG

Cut off and dispose of the supplied

plug if it does not fit your socket.

WARNING: To avoid a shock haz-

ard do not insert this plug into a

socket anywhere else.

IMPORTANT: WIRES IN THE MAINS

LEAD ARE COLOURED IN

ACCORDANCE WITH THE

FOLLOWING CODE:

Green/Yellow – Earth

Blue – Neutral

Brown – Live

If you change the plug, the colour of wires in the mains lead may not correspond with the

colour of the markings identifying terminals in the plug.You should therefore wire it as

shown (see illustration). If the mains lead needs to be replaced at any time, it should be

replaced by a special lead obtainable from your local authorised Creda Service Centre.

A charge will be made if you have damaged the existing lead or require a longer one.

It is strongly advised that this work is carried out by a qualified electrician.

CE marking certifies that this appliance complies with requirements laid down in EEC

Directive 89:336 (Electromagnetic compatibility) and subsequent modifications and Low

Voltage Directive 73/23/EEC.

Green and yellow

(Earth) wire to the

terminal marked

‘E’ or with the

symbol ,

or coloured

green and

yellow.

Brown (Live)

wire to the

terminal

marked ‘L’or

coloured

red.

Blue (Neutral) wire

to the terminal marked

‘N’ or coloured black.

Cord clamp

13A ASTA

approved

fuse to

BS1362.

Contents

Electrical requirements 2

Recycling & Disposal Information

Choosing a Location

Adjusting the Feet

Installation Instructions 3-4

Transit Bracket Removal

Connecting to the Water Supply

Removing the Polystyrene Pyramid

Connecting to a Drainage System

Getting to Know your Machine 5

Wash Load Guides

Interlocking Door System

Washcare tips

A Typical Wash Programme 6

Controls 7

Choosing A Wash Programme 8

Optional Wash Features 9

Dispenser Drawer 10-11

Care and Cleaning 12

Maintenance Wash

Regular Checks and Stain Removal 13

Something wrong with your appliance 14

Service Cover 15

Key Contact Numbers Back page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Creda W120VW Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info