169009
27
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
25
DSX4500
27
EXAMPLE 3-Channel Mode: 1 x Stereo System & 1 x Mono Subwoofer bridged
INTERCONNECTION
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables. If a
separate SUB OUT from your headunit is available, use this for the LINE INPUT CH3/4 on the amplifier.
Connect the speakers with SPEAKER OUTPUT + CH 1 - and + CH 2 - and the subwoofer with the SPEAKER OUTPUT CH3/4
+ BRIDGED - of the amplifier.
Ensure by any means, that the total impedance load of all speakers per channelpair (CH1 & CH2) is not lower than 2 ohms and the total
impedance load of the subwoofer (CH3 & CH4) is not lower than 4 ohms. Too low impedance cause high temperature and will shut down
the amplifier operation.
CROSSOVER SETTINGS CH1/2 (STEREO-SYSTEM)
• Observe the settings on page 25.
CROSSOVER SETTINGS CH3/4 (SUBWOOFER)
• Observe the settings on page 26.
LEVEL CONTROLLER CH1/2 & CH3/4 (STEREO SYSTEM & SUBWOOFER)
• Turn the INPUT LEVEL controller of the amplifier to the 6V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the INPUT LEVEL controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER CH1/2 (STEREO-SYSTEM)
• The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
BASS BOOST CONTROLLER CH3/4 (SUBWOOFER)
• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
Connect the stereo RCA output (FL/FR and
RL/RR) of the headunit with LINE INPUTS
CH1/2 and CH3/4 of the amplifier
Speaker
front/right
2 – 8 Ohms
LINE INPUT OUTPUT
R
L
CH1/CH2
CH3/CH4
LOW PASS
BASS BOOST
INPUT LEVELHIGH PASS
X-OVER
LP/BP FULL
HP
LOW PASS
BASS BOOST
INPUT LEVELHIGH PASS
X-OVER
LP/BP FULL
HP
CH1 CH3
CH2 CH4
30Hz
150Hz
0dB 12dB
6V
0.2V
10Hz
150Hz
30Hz
150Hz
0dB 12dB
6V 0.2V
10Hz
150Hz
POWER INPUT
GND REM
SPEAKER OUTPUT
CH1 CH2 CH3 CH4
BRIDGED BRIDGED
FUSE
12V
Speaker
front/left
2 – 8 Ohms
RR RLFL FR
Switch position HP or FULL
Switch position
LP/BP
Subwoofer
4 – 8 Ohms
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch dsx4500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info