Bedienungsanleitung Crunch GP1500.4 (Seite 17 von 28) (Deutsch, Englisch)

498246

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

General Installation Notes

The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such

as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and

protection from moisture. When considering the mounting location you should minimize the length of the

power and speaker leads. Minimizing both leads will yield a more reliable installation. It is also important

to ensure that the heat sink fins are not against a panel or a surface, preventing air circulation. Do not

install the amplifier on a subwoofer box or on vibrating parts of the vehicle, since the vibrations can cause

damage to the amplifiers electrical components.

Installation of the amplifier

Mark the location for the mounting screw holes by using the

amplifier as a template. Drill holes at the marked locations and

firmly fasten the amplifier in place with the mounting screws

supplied in the accessory kit.

Before drilling or cutting any holes, investigate the layout of your

automobile thoroughly: Take care when working near the gas lines

or hydraulic lines and electrical wiring.

Electrical Connection

Ground (GND)

This wire is the electrical ground and must be fastened securely to the vehicle chassis. The best method is to use a threading sheet

metal screw since the threads cut into bare metal. Ensure that all paint or other insulation is remove from around the hole area, and

using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable as possible - use the

same gauge as was used for the +12V cable. Make sure that the connection is safe, a loose connection may result in amplifier noise

and fault condition.

Remote (REM)

Many radios or other music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio

doesn't have a remote turn-on feature, then you can use the antenna relay wire, which activates the antenna motor. Please note, if the

power antenna retracts when the radio is operating, then you cannot use the antenna relay wire to operate the remote turn-on.

Batterie Connection (+12V)

This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an assigned fuse

in line with the + power supply wire. Please use a sufficient gauge for the installed amplifiers (min. 10-16 mm² for GP1000.2 and

GP1000.4 or min 16-25 mm² for GP1500.2 and GP1500.4).

This connection must be Completed using spade lug with

Insulating sleeve.

Fuses

The integrated amplifier fuses protect the units from

short circuit and overload. The fuse rating is for 4 Ohm

loads (impedance) of the speakers, for 2 Ohm loads

the fuses may have to get increased by up to 50%

in case of higher power consumption.

CHASSIS

GROUND

Remote

CHASSIS

GROUND

Battery

Fuse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crunch GP1500.4 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info