498262
10
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
10
ENG
LOUDSPEAKER CONNECTIONS
- In 2-channel operation (i.e. one loudspeaker on each amplifier channel), the impedance must
not be lower than 2 ohms for each speaker
- In bridging mode (two amplifier outputs combined) the impedance must not be lower than 4 ohms
for the bridged output.
- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.
If the amplifier is operated with a too low impedance or incorrectly used, the entire sound system
may be damaged. This means a warranty void in such cases.
SIGNAL OUTPUTS TO CONNECT AN ADDITIONAL AMPLIFIER
Due to its compact design, the amplifier has no signal outputs to supply additional amplifiers, such as
a mono subwoofer amplifier. Split in this case the input signal with a suitable Y-connector to provide
the input signal to both amplifiers.
OPERATING ELEMENTS
Turn the input level control (LEVEL INPUT, Fig. 1, 3) on the amplifier to the MIN. position. Turn then
the volume control of the headunit to 80% - 90% of its maximum volume. Now turn slowly the input
level control on the amplifier (LEVEL INPUT, Fig. 1, 3) in a clockwise direction until you hear some
distortion, then turn back slightly until the distortion is not audible anymore.
INPUT SENSITIVITY
The HIGH LEVEL INPUT (Fig. 1, 1) is suitable to connect the amplifier inputs with speaker wires, if
your headunit is not equipped with pre-amplifier RCA outputs. Extend therefore every regarding speaker
cable from your headunit with appropriate speaker cables from your car audio retailer to the mounting
location of the amplifier. Then connect the each matching loudspeaker cable with the cables of the
included HIGH LEVEL jack like described below.
NOTE: Never use the HIGH LEVEL INPUT and the RCA inputs at the same time. This may damage
the amplifier seriously. The loudspeaker cables of the HIGH LEVEL INPUT must have no contact to the
ground (GND).
HIGH LEVEL INPUT
The amplifier detects a voltage rise (6 Volts) with a so called ”DC Offset” over the connected input
signal on the HIGH LEVEL INPUT (Fig. 1, 1) when the headunit will be switched on. Hence, the amplifier
will also be turned on. As soon as the headunit will be turned off, the amplifier turns also automatically
off. In this case the turn-on connection (Fig. 2, 2) is not needed.
Note: The Auto Turn On function usually works with 90% of all headunits, because they are equipped
with ”High Power”-outputs. Only with a few older and still existing headunits the Auto Turn On function
is not working.
AUTO TURN ON
+
-
blue = speaker - right - positive
-
+
white = speaker - right - negative
orange = speaker - left - negative
yellow = speaker - left - positive
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch GTO2120 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info