Bedienungsanleitung Crunch GTR 2400.1 (Seite 13 von 20) (Deutsch, Englisch)

498239

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1-Channel-Mode: 1 Subwoofer / Mono

Speaker- & RCA-Connection

GTR1200.1

POWERPOWER

PROTECTPROTECT

BASS REMOTEBASS REMOTE

6V6V

40Hz40Hz

150Hz150Hz

0dB0dB 12dB12dB

BOOSTBOOST

0.2V0.2V

P ASSP ASS

I NPUTI NPUT

15Hz15Hz

55Hz55Hz

S ONICS ONIC

BASSBASS

LOWLOW

LEVELLEVEL

SUBSUB

CONTROL P ANELCONTROL P ANEL

OUTPUT OUTPUT

LINE INPUT LINE INPUT

FUS E

SPEAKER OUTPUT

GND REM 12V

POWER INPUT

Subwoofer

1 - 8 Ohm

Caution

Please avoid to connect speaker (-) to the ground or vehicle chassis.

Cable connection

• Connect INPUT of the amplifier to the head unit line output with good quality RCA cables.

By connecting the RCA jacks OUTPUT with a additional amplifier, a full range signal will be

provided to the amplifier. If your head unit is equiped with a separate Subwoofer Output it

is suggested to use this.

• Connect the subwoofer with the terminal block (SPEAKER OUTPUTS + / -) of the amplifier.

As option a additional Subwoofer can also be connected. The minimum total impedance

of both Subwoofer must be higher than 1 Ohm.

• Too low speaker loads result in too high heat dissipation and may cause the amplifier run into

protection.

• Please observe speaker channel and polarity as printed by the speaker terminal block.

Incorrect phasing of the speakers results in total loss of bass response.

•

LOW PASS - Control

• Adjust a frequency between 40Hz - 150Hz, depending on the size and response of the Subwoofer.

SUBSONIC - Control

• The SUBSONIC - Control adjusts the cut-off of the Subsonic-Frequency (lower Frequency cut-off).

Therewith a BANDPASS-Signal will be generated, where too low and not hearable frequencies will be eliminated.

Thereby a clean and powerful Bass-Signal will be generated. The adjustable level depends on the size and response of the

subwoofer and should be between 15Hz (no cut-off) and 55Hz (max. cut-off Level).

NOTE: If the SUBSONIC - Level is higher than the LOW PASS - Level, no Sound is hearable.

LEVEL INPUT - Control

• Turn the LEVEL INPUT - Control on the amplifier to "6V" position.

• Turn the head unit volume control to about 80-90% of its full setting.

• Turn the LEVEL INPUT - Control clockwise until you hear some distortion.

• Then turn back the LEVEL INPUT - Control slightly until you can hear clean sound.

BASS BOOST - Control

• The BASS BOOST - Control adjusts the bass level at 45 Hz from 0 up to 12dB. Please use the Bass-Boost carefully.

BASS REMOTE

• The BASS REMOTE allows to control the Bass-Level for example from the driver's seat.

Connect RCA cable

from head-unit with

RCA input (INPUT).

BASS REMOTE

OPTION:

As option an additional Subwoofer can be

connected with the non-occuppied Speaker

Terminals. Thereby check by any means the

changed impedance, the total impedance of both

subwoofers should not be lower than 1 ohm.

Maybe the Fuses of the Amplifier have to be

replaced with a higher Fuse Rating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Crunch GTR 2400.1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info