498241
16
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
2 Channel Amplifier - Speaker- & RCA-Connection
GTR420.2 – GTR620.2
16
Connect RCA cable
from head-unit with
RCA input INPUT).
Cable connection
• Connect INPUT of the amplifier to the head unit line output with good quality RCA cables.
By connecting the RCA jacks OUTPUT with a additional amplifier, a full range signal will be
provided to the amplifier.
• Connect the speakers with the terminal block (SPEAKER OUTPUT + L - und + R -) of the
amplifier.
• The minimum final speaker impedance must not be below 2 Ohm per channel. Too low
speaker loads result in too high heat dissipation and may cause the amplifier run into
protection.
• Please observe speaker channel and polarity as printed by the speaker terminal block.
Incorrect phasing of the speakers results in total loss of bass response.
X-OVER - Switch & Control
If larger than 20 cm speakers are used, the "FULL" position is recommended.
• For all smaller speakers (8.7cm - 16cm) the "HP"-Position (HIGH PASS) is recommended, which
eliminates the lowest frequencies and protects the speakers from damage. Set the crossover-frequency
between 10Hz - 1200Hz, depending on the size of the installed speakers. The Highpass adjustment can be
done with the HIGH PASS control. In this configuration the LOW PASS control is not in use.
LEVEL INPUT - Control
• Turn the LEVEL INPUT - Control on the amplifier to "4V" position.
• Turn the head unit volume control to about 80-90% of its full setting.
• Turn the LEVEL INPUT - Control clockwise until you hear some distortion.
• Then turn back the LEVEL INPUT - control slightly until you can hear clean sound.
BASS BOOST - Control
• Turn the BASS BOOST - Control into “0dB” - position.
BASS REMOTE
• In this configuration the BASS REMOTE is not in use.
2-Channel-Mode: 2 Speakers / Stereo
Caution
Please avoid to connect speaker (-) to the ground or vehicle chassis.
Speakers (Right) 2 - 8 Ohms
Speakers (Left) 2 - 8 Ohms
OUTPUT OUTPUT
LL
RR
INPUT INPUT
LL
RR
POWERPOWER
PROTECTPROTECT
BASS REMOTEBASS REMOTE
HPHP
LP/BPLP/BP
FULLFULL
X-OVERX-OVER
BPFBPF
4V4V
30Hz30Hz
150Hz150Hz
0dB0dB 12dB12dB
BASS B OOSTBASS B OOST
0.2V0.2V
1.2kHz1.2kHz
10Hz10Hz
HIGH P ASSHIGH P ASSLOW P ASSLOW P ASS
LEVEL I NPUTLEVEL I NPUT
FUS E
BRIDGED
SPEAKER OUTPUT
GND REM 12V
POWER INPUT
L R
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch GTR440.4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info