168680
19
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
Before you start with the installation of the sound system, disconnect by any means the GROUND connection
wire from the battery, to avoid any risk of electric shock and short circuits.
REFERENCE NOTE
INSTALLATION INSTRUCTIONS
19
MECHANICAL INSTALLATION
Avoid any damage removing of the components of the vehicle like wires, cables, board computer, seat belts, gastank or the like.
Ensure that chosen location provide sufficient air circulation for the amplifier. Do not mount the device into small or sealed spaces without
air circulation near by heat dispersing parts or electrical parts of the vehicle.
Do not mount the amplifier on top of a subwooferbox or any other vibrating parts, thereby parts in the inside of the amplifier may get loosen.
The wires and cables of power supply and the audio signal must be as short as possible, to avoid any losses and interferences.
Amplifier
Mounting
bracket
Mounting
bracket
Vehicle
2
1
43
Pen or
peening
tool
Before mounting the brackets you should remove the
castparts on each end. Then install the 4 supplied mounting
brackets on the bottom side of the amplifier with the supplied
screws. Ensure that the angled side of the brackets are
pointed to the inner side. The pre-drilled screw holes are
located on each corner of the amplifier.
Uphold the amplifier with the mounted brackets to the
chosen mounting location in the vehicle. Then mark the
four drill holes with a appropriate pen or peening tool and
lead through the designated holes of the mounting brackets.
Observe that there remains enough space for the installation
of the cables and ensure that they will not be bended and
have sufficient pull relief.
Put the amplifier aside and then drill the holes for the
mounting screws at the before marked locations. Please
ensure not to damage any components of the vehicle while
drilling the holes. Alternatively (depends on the material of
the surface) you can also use self-tapping screws.
Then uphold the amplifier to the chosen position and fix
the screws through the holes of the mounting brackets into
the drilled screwholes. Ensure that the mounted amplifier
is fixed tight and not get loosen.
Amplifier
Mounting
bracket
Vehicle
Mounting
screws
Amplifier
4 x
Vehicle
Drill
Marking
4 x
4 x
4 x
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch gtx 2400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info