168680
26
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
GTX4600 - GTX4800
26
INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged
Do not connect loudspeaker cables with the vehicle’s chassis.
Always ensure the correct polarity of all connections.
REFERENCE NOTE
Use the bass enhancement with care.
A high bass boost may cause damage to your speakers and hearing abilities.
INTERCONNECTION
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT CH 1 and CH 2 of the amplifier with appropriate high-value
RCA cables. If a separate SUB OUT from your headunit is available, use this as LINE OUT.
Connect the subwoofers with the SPEAKER OUTPUTS CH1/2 + BRIDGED - and CH3/4 + BRIDGED -.
Ensure by any means, that the total impedance load of all subwoofers per channelpair is not lower than 4 ohms. Too low impedance
cause high temperature and will shut down the amplifier operation.
Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INPUT MODE SWITCH
Select the 2CH position on the INPUT MODE switch.
CROSSOVER SETTINGS & BASS BOOST CONTROLLER
• The X-OVER switch must be in position LP/BP and the TWIN SUB switch in position ON.
All filter controllers (BASS BOOST, HIGH PASS, LOW PASS, LEVEL) of CH 1/2 are without function in TWIN SUB mode.
LEVEL INPUT CONTROLLER CH3/4 (SUBWOOFER 1+2)
Observe the regarding notes on page 23.
• All LEVEL INPUT CONTROLLERS of CH1/2 are without function.
TWIN SUB & BASS REMOTE CH1/2 (SUBWOOFER 1) & CH3/4 (SUBWOOFER 2)
The enclosed BASS REMOTE controller adjusts the bass-level e.g. from the driver’s seat.
That this BASS REMOTE controller is effective on both channel pairs (CH1/2 & CH3/4) you MUST set TWIN SUB switch in
position ON. Please use only the enclosed bass remote controller and cable.
Is the TWIN SUB switch on position ON, the controllers BASS BOOST, HIGH PASS, LOW PASS, LEVEL on CH1/2 are without function.
All settings will be synchronized with CH3/4. In switch position OFF, the bass remote works only on CH3/4.
Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of the amplifier
Subwoofer 2
4 – 8 Ohms
Subwoofer 1
4 – 8 Ohms
R L
Switch position CH3/4 = LP/BP
TWIN SUB = ON
Connect the bass remote
controller and the
remote terminal on the amplifier
with the enclosed cable.
INPUT MODE = 2 CH
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch gtx 2400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info