168681
27
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
25
GTX4600 - GTX4800
27
EXAMPLE 3-Channel Mode: 1 x Stereo System & 1 x Mono Subwoofer bridged
INTERCONNECTION
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables. If a
separate SUB OUT from your headunit is available, use this for the LINE INPUT CH3/4 on the amplifier.
Connect the speakers with SPEAKER OUTPUT + CH 1 - and + CH 2 - and the subwoofer with the SPEAKER OUTPUT CH3/4
+ BRIDGED - of the amplifier.
Ensure by any means, that the total impedance load of all speakers per channelpair (CH1 & CH2) is not lower than 2 ohms and the total
impedance load of the subwoofer (CH3 & CH4) is not lower than 4 ohms. Too low impedance cause high temperature and will shut down
the amplifier operation.
INPUT MODE SWITCH
• Observe the regarding notes on page 25.
CROSSOVER SETTINGS CH1/2 (STEREO SYSTEM)
• Observe the regarding notes on page 22.
LEVER CONTROLLER CH1/2 (STEREO SYSTEM)
• Observe the regarding notes on page 22.
BASS BOOST CONTROLLER CH1/2 (STEREO SYSTEM)
• The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
CROSSOVER SETTINGS CH3/4 (SUBWOOFER )
• Observe the regarding notes on page 23.
LEVER CONTROLLER CH3/4 (SUBWOOFER )
• Observe the regarding notes on page 23.
BASS BOOST CONTROLLER CH3/4 (SUBWOOFER )
• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
BASS REMOTE CH3/4 (SUBWOOFER )
The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver’s seat of the Subwoofer on CH 3/4.
Please use only this enclosed bass remote controller and cable.
TWIN SUB SWITCH
• Select position OFF on the TWIN SUB switch.
FR FL
Connect the stereo RCA output (FL/FR and RL/RR) of the headunit
with LINE INPUTS CH1/2 and CH3/4 of the amplifier
RL RR
Subwoofer
4 – 8 Ohms
Speaker
left
2 – 8 Ohms
Speaker
right
2 – 8 Ohms
Switch position CH1/2 = HP or FULL and CH3/4 = LP/BP
TWIN SUB = OFF
Connect the bass remote
controller and the
remote terminal on the amplifier
with the enclosed cable.
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch gtx4600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info