498243
13
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
REMOTE
CONTROL
REFERENCE NOTE: Ensure always correct polarity for all connections.
Don’t connect any speaker cables to the vehicle’s ground.
Loudspeaker- and Audio-Connections
Connect the RCA INPUTS of the amplifier to the head unit line outputs with appropriate RCA cables.
Connect the Subwoofer with the speaker outputs (SPEAKER OUTPUT/ - +) of the amplifier by using appropriate
cables.
Ensure that the total speaker impedance load is not lower than 1 Ohms.
Too low speaker loads result in too high heat development and may cause the amplifier run into protection.
INPUT LEVEL - controller
• Turn the INPUT LEVEL - controller on the amplifier to 5V position.
• Turn the head unit volume controller to about 80-90% of its full setting.
• Turn the INPUT LEVEL - controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL - controller slightly until you can hear clean sound.
REFERENCE NOTE: If this controller is cranked up too high, the amplifier produce distortions, which may cause a
“creeping death” of the amplifier (or the speakers). Usually this is called “Clipping”.
LOWPASS - controller
The lowpass filter eliminates the higher frequencies. The recommended crossover frequency ranges between 60-100Hz,
depending on the size and response of the Subwoofer.
SUBSONIC - controller
• The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below,
to avoid a mechanical and electrical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz
and depends on the size of the subwoofer.
BASS BOOST - controller
• The BASS BOOST - controller adjusts the bass boost level at 45 Hz from 0db to +12dB.
Caution! Please use the Bass Boost carefully.
Connect the RCA cable from head-unit
or a additional multichannel-amplifier
with RCA input
Connect cable from REMOTE CONTROL
with the input jack of the amplifier.
Subwoofer 1 - 8 Ohms
The optional RCA Fullrange Outputs
(OUTPUT) are forwarding the audiosignal.
A additional subwoofer can be
connected to the non-occupied
speaker outputs. In this case
ensure a impedance of 2 - 8
ohms per subwoofer.
13
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Crunch MXB750 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info