Bedienungsanleitung Cuisinart FP-14 (Seite 18 von 20) (Englisch)

498294

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

8. Problem: Dough feels tough after kneading

Solution:

•

Divide dough into 2 or 3 pieces and

redistribute evenly in bowl. Process 10

seconds or until uniformly soft and pliable.

9. Problem: Dough is too dry.

Solution:

• While machine is running, add water, 1

tablespoon at a time until dough cleans

the inside of the bowl.

10. Problem: Dough is too wet.

Solution:

• While machine is running, add flour, 1

tablespoon at a time until dough cleans

the inside of the bowl.

Technical

1. Problem: The motor does not start.

Solution:

• There is a safety interlock to prevent the

motor from starting if it is not properly

assembled. Make sure the work bowl

and work bowl cover are securely locked

into position.

• If you are slicing or shredding and the

above solution does not work, make sure

that the food contents in the feed tube

are cut below the maximum fill line so

that the activation rod can engage the

motor.

• If the motor still will not start, check the

power cord and outlet.

2. Problem: The food processor shuts off

during operation.

Solution:

• The cover may have become unlocked;

check to make sure it is securely in

position.

• A safety protector in the motor prevents

the motor from overheating, which is

caused by excessive strain. Press the Off

control button and wait 10 to 15 minutes

to allow the food processor to cool off

before resuming.

3. Problem: The food processor cover

becomes unlatched in the back and or

makes a loud noise.

Solution:

• The back of the cover becoming

unlatched, and any related noise, will not

prevent the unit from working. Simply

push down to lock the back into position.

4. Problem: The motor slowed down during

operation.

Solution:

• This is normal as some heavier loads (e.g.

slicing/shredding cheese) may require the

motor to work harder. Simply reposition

the food in the feed tube and try again.

• The maximum load capacity may have

been exceeded. Remove some of the

ingredients and continue processing.

5. Problem: It is difficult to remove the

chopping/mixing blade from the work bowl.

Solution:

• These innovative blades have been

designed to lock in the work bowl to

prevent them from falling out when

emptying the contents of the bowl. Using

extreme care, use a little extra force to

remove the blade.

6. Problem: The food processor vibrated/

moved around the countertop during

processing.

Solution:

• Make sure the rubber feet at the bottom

of the unit are clean and dry. Also make

sure that the maximum load capacity is

not being exceeded.

• This is normal as some heavier loads (e.g.

slicing/shredding cheese) may require the

motor to work harder.

7. Problem: The large pusher falls out when

the cover is turned upside down.

Solution:

• The pusher lock feature, located above

the handle, should be pulled out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cuisinart FP-14 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cuisinart FP-14

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info