Bedienungsanleitung Cyberhome CH-DVD 300 (Seite 23 von 27) (Englisch)

498379

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

SCAN MODE

Default setting: INTERLACED

When using YUV ouputs, you can change this setting. DO

NOT USE this setting if your TV does not support Progressive

Scan. Use the UP / DOWN ARROW and ENTER keys to

select PROGRESSIVE.

BRIGHTNESS

Here is where you can set the BRIGHTNESS level. Use the

LEFT / RIGHT ARROW keys to make adjustments.

CONTRAST

Adjust the CONTRAST level with the LEFT / RIGHT

ARROW keys.

LAST MEMORY

Adjust the SATURATION of the video output with the LEFT /

RIGHT ARROW keys.

THE DVD PLAYER SETUP MENU

The DVD setup menu

The settings you choose in the Audio Setup Page will be

determined by the type of audio equipment you are using with

the DVD Player. The factory default settings are configured

with the assumption that you are using the player with a

standard TV supporting Stereo Audio Inputs. This menu will

allow you to enable the Digital Audio Output if you wish to use

the Coaxial Digital Audio Output with a Digital Receiver.

DIGITAL OUTPUT

SPDIF ( Sony / Phillips Digital InterFace ) refers to the digital

audio format used by most consumer electronics equipment as

well as the Coaxial Digital Audio Output connector. If you are

using the Stereo Audio Output, change this setting to

BITSTREAM or LPCM. Generally, the BITSTREAM setting

is used with receivers capable of Dolby Digital 5.1 channel

decoding, while the LPCM 48K setting is reserved for two

channel equipment.

MENU, AUDIO, SUBTITLE LANGUAGE

Default setting: ENGLISH

Use these settings to set the player’s preferred language for

DVD Audio tracks, subtitles and menus.

TV DISPLAY

Default setting: 4 :3 PS

You can setup your DVD Player to work with normal and wide

screen televisions. If you are using a wide screen TV, set this

option to 16:9 to match the aspect ratio of your TV. When used

with a normal TV (4:3 aspect ratio), the 4:3 PS setting results

in the typical “Pan & Scan” display, where a movie is clipped

on the sides to fit into the TV screen. The 4:3 LB setting will

enable the “Letterbox” format, where the movie is presented in

wide screen format with black lines at the top and bottom of

the screen. Note: The PS and LB usually will have no effect,

since very few movies support both options. DVDs are

generally recorded with either PS or LB and do not allow

switching between the two.

ANGLE MARK

Default setting: ON

When used with discs supporting multi-angle features, the

Angle Mark continuously displays the current angle you’re

viewing on screen. Setting ANGLE MARK to OFF will cancel

continuous display, and the current angle will be displayed on-

screen for just a few seconds after an angle change.

DVD SETUP

MENU ENGLISH

AUDIO ENGLISH

SUBTITLE ENGLISH

TV SCREEN 4:3 PS

ANGLE MARK ON

CLOSE CAPTIONS ON

PARENTAL CONTROL 8

NEW PASSWORD _ _ _ _

DVD

CLOSED CAPTIONS

Default setting: OFF

Not all discs support Closed Captions. However, setting

CLOSE CAPTION to ON will display captions when

supporting discs are used. If you don’t wish to automatically

enable captions, set this option to OFF.

PARENTAL CONTR

Default setting: 8

The Parental Lock allows you to limit the use of your DVD

Player to only those DVD discs that do not exceed the rating

you specify. When the Parental Control is set, DVD discs that

support this feature will play only after the password has been

entered. However, typically only discs produced by major

entertainment companies support Parental Control. You can

choose from eight levels of Parental Control, corresponding to

the standard rating system in the USA. You will need to enter a

valid password before making changes to Parental Control

settings - refer to the section below.

PASSWORD

To begin using the Parental Control, enter the factory password

of 3351. Once this password is entered, you will be able to

change the Parental Control setting or enter an additional user

password (the factory password cannot be deleted or changed).

To enter your own user password, key in a four digit number

into the NEW PASSWORD field. The user password and the

factory password can now both be used. You can change the

user password at any time after entering a valid password. The

user password is useful for allowing others - for example a

babysitter - temporary access to Parental Control settings.

The audio setup menu

Remember to keep in mind that the key to the Parental

Control feature is the factory default password of 3351.

Consequently, your player may not be secure if this manual is

accessible by your children.

Note on parental security

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cyberhome CH-DVD 300 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info