7
CLEANING
– Do not use abrasives to clean the frame! Use a damp cloth and a mild detergent
and dry thoroughly.
– Should the stroller be exposed to salt water, please rinse it down with fresh (tap) water
as soon as possible afterwards.
– Seat covers are machine washable at max. 30° C on delicate cycle. The canopy
can be hand washed with mild detergent at max. 30° C.
– Please make note of the care label. Do not tumble dry. Let covers dry completely
before reuse.
– All CYBEX fabrics have been tested, but when the stroller is very wet, the water may
permeate the lining through the bottom edges and seams and leave water stains
on the upholstery. We advise you to use a rain cover to avoid this. Also please do not
fold or store the product while wet. If the stroller is wet, allow to dry with the canopy
extended. Never store in a damp environment as this can cause mildew to form.
Note! Please wash the cover separately before you use it the first time. Do not tumble dry
and do not expose to direct sunlight! Do not iron!
INSTRUCTIONS FOR USE
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR
FUTURE REFERENCE. YOUR CHILD’S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW
THESE INSTRUCTIONS.
THIS PRODUCT WAS APPROVED ACCORDING TO THE EN 1888:2003 + A1/A2/A3:2005
STANDARD.
1. OPENING THE STROLLER
a) Before opening the pushchair the safety lock needs to be released.
b) After releasing the safety clip you can unfold the pushchair.
c) Step on the footboard until it locks in place with an audible click.
d) Please make sure that the handle bar is safely locked as well.
WARNING: CHECK THAT THE SEAT UNIT ATTACHMENT DEVICES AND CARRYCOT/CAR SEAT
ADAPTERS ARE CORRECTLY ENGAGED.
ensure that the locking and swiveling mechanism are treated regularly with Teflon
spray (dry lubricant). It is important that brakes, wheels and tyres are not impaired
during use. Inspect them regularly and repair or replace if necessary. STOP using any
product that does not appear structurally sound.
– Do not make any modifications to the product. If you have any complaints or
problems, please contact your supplier or importer.
– A service should be scheduled every 12 months.
– You can also treat the other moving parts with Teflon spray (dry lubricant). After
spraying on the Teflon, wipe the product with a soft cloth.
– Use only original CYBEX replacement parts. It may be unsafe to use substitutes.
– The frame tubes covered by the locking mechanism and turning mechanism should
also be regularly cleaned and sprayed. This will ensure that you enjoy your stroller
without any problems.
2. ASSEMBING THE WHEELS
a), b) Front wheel assembly.
c), d) e) Rear wheel assembly. Make sure that both mudguards point outwards.
f) After assembling the wheels the bowden brake cable can easily be lodged into the
designated slots.
3. AUTOMATIC FRONT WHEEL SWIVEL LOCKS
4. USING THE BRAKES
– Regardless of their position, the front wheels can be automatically locked into place
by stepping on the lock button (wait for an audible CLICK). To release the lock press
again until you hear a CLICK.
– Tilt the lever located at the right wheel to secure the brake. To release the brake tilt
the lever again.
5. USING THE HARNESS SYSTEM
a) To fasten the harness system insert left and right side fasteners into the central harness
buckle.
b) To tighten the belts pull the strap on the front of the central harness buckle.
c) To release the belt system press the release button located on the seat in front of the
belt lock while pulling at the shoulder belts.
d) To release the fasteners squeeze the grooves on left and right side of the central
harness buckle.
e) Adjust the length of the crotch strap with the corresponding slider under the seat
cover.
6. ADJUSTING THE HARNESS SYSTEM FOR NEWBORNS
– Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
– Completely pull the shoulder straps out of the holes in the backrest.
– Feed the shoulder straps through the two bottom holes. Make sure to feed the straps
back through the holes in the backrest mechanism and re-attach them to the triangle.
– To adjust the length of the shoulder straps to newborns please attach the inner loop
of the shoulder strap ends to the triangular ring.
Switch back to the upper holes as soon as the shoulder straps do no longer fit over the
child´s shoulders.
a) Remove the headhugger as soon as the headhugger does no longer fit over the
child´s shoulders.
b) Remove the velcros of the headhugger on the top left and right side on the back of
the seat cover. Release the loops at the end of the shoulder straps from the triangle
in the belt system, situated at the bottom of the backrest under the seat cover.
– Completely pull the shoulder straps out of the holes in the backrest.
c) Pull the shoulder straps through the shoulder pads and the headhugger. Make sure
to feed the straps back through the holes in the backrest mechanism and attach
them to the triangle.
You can use the haedhugger and the shoulder pads separately.
7. REMOVING THE HEADHUGGER AND SHOULDER PADS
