Bedienungsanleitung Daikin ATX35J2V1B (Seite 10 von 16) (Englisch)

642448

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

7 English

Indoor Unit Installation

3-2. Left-side, left-back, or left-bottom piping.

1) Attach the drain hose to the underside of the refrigerant pipes

with adhesive vinyl tape.

2) Be sure to connect the drain hose to the drain port in place of

a drain plug.

3) Shape the refrigerant pipe along the pipe

path marking on the mounting plate.

4) Pass drain hose and refrigerant pipes

through the wall hole, then set the indoor

unit on mounting plate hooks, using the

markings at the top of the indoor unit as

a guide.

5) Pull in the interconnecting wires.

6) Connect the inter-unit piping.

7) Wrap the refrigerant pipes and drain hose together with insulation tape as

right figure, in case of setting the drain hose through the back of the indoor

unit.

8) While exercising care so that the interconnecting wires do not catch indoor

unit, press the bottom edge of indoor unit with both hands until it is firmly

caught by the mounting plate hooks. Secure indoor unit to the mounting

plate with screws (M4 × 12L).

3-3. Wall embedded piping.

Follow the instructions given under

1) Insert the drain hose to this depth so it won’t be pulled out of the drain pipe.

How to replace the drain plug and drain hose.

• Replacing onto the left side

1) Remove the insulation fixing screws on the

right to remove the drain hose.

2) Reattach the insulation fixing screw on the

right as it was.

* (Forgetting to attach this may cause water

leakages.)

3) Remove the drain plug on the left side and

attach it to the right side.

4) Insert the drain hose and tighten with

included indoor unit fixing screw.

Left-side, left-back, or left-bottom piping

Drain hose attachment position

* The drain hose is on the back of the unit.

Front side of unit

Attachment on the right side (factory default)

Attachment on the left side

Drain hose Drain hose

Indoor unit

ﬁxing screw

Insulation

ﬁxing screw

Left side Right side

Remove pipe port cover here for left-bottom piping.

Remove pipe

port cover

here for left-

side piping.

Left-bottom piping

Left-side

piping

Left-back

piping

How to set drain plug.

No gap.

Do not apply lubricating

oil (refrigeration oil)

when inserting.

Application of causes

deterioration and drain

leakage of the plug.

Insert a hexagon wrench (4mm).

Drain

hose

Caulk this hole

with putty or

caulking material.

Bind with vinyl

tape.

Mounting plate

Wrap insulating tape around the

bent portion of refrigerant pipe.

Overlap at least half the width of

the tape with each turn.

Refrigerant

pipes

Drain hose

Bottom frame

M4 × 12L (2 point)

Mounting

plate

Inter-unit wiring

Inner wall

Vinyl chloride

drain pipe

(VP-30)

Drain hose50mm

or more

Insert drain hose

to this depth so

it won’t be pulled

out of drain pipe.

Outer wall

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Daikin ATX35J2V1B Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Daikin ATX35J2V1B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info