Bedienungsanleitung Danfoss TP5000 Si (Seite 2 von 2) (Englisch)

769335

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Danfoss Randall Ltd

Ampthill Road

Bedford, MK42 9ER

Tel: 0845 1217 400

Fax: 0845 1217 515

Email: danfossrandall@danfoss.com

Website: www.danfoss-randall.co.uk

Fig.10

Fig.11

Selection of time

or actual room

temperature in main

LCD display

Temporary

override of

programmed

temperature

press

together

Frost

Protection

Fig.9

Fig.12

Temporary User Overrides

The TP5000 has several useful overrides which can be selected without aﬀecting the

thermostat programming.

• Selection of time or actual room temperature in main LCD display – press +

and – together to change between settings (Fig. 9).

• Temporary override of programmed temperature – press Λ or V until required

temperature is displayed (override will automatically cancel at beginning of next

programmed event) (Fig. 10).

• Frost Protection – a constant low temperature can be selected whilst away from

home - press Λ and V together (Fig.11). Then use Λ or V to select the required

temperature. To return to automatic programming press Λ and V together again.

Battery Replacement

• Alowbattery symbol will ﬂash in the LCD display (Fig. 12)

You have 15 days to replace the battery before the unit will switch oﬀ. •

Remove old batteries and insert new ones. All settings including time are •

maintained.

Press and release the •RESET button to restart the unit. (Fig. 1)

NB. If the display ever goes blank during normal operation, the batteries will need

to be renewed with high quality alkaline cells. The reset button should be pressed

to restart the unit. All times, dates and events will be retained and need not be re-

programmed.

If the property is owned by a landlord he may, for gas safety reasons, have instructed the installer

to set the service interval timer.

If set a visual and audible warning will alert you that the boiler will need servicing within the next

28 days. This warning is repeated each day at noon. (Fig. 15)

If the boiler is not serviced within 28 days the daily audible warning will sound continuously and

can only be cancelled each day by pressing any button on the unit.

In addition, all overrides and programming buttons will be disabled and the heating and hot water

will only operate for 15 minutes in each programmed hour.

As this is a gas safety feature only an installer can reset the service interval timer. This will be done

as part of the boiler service as part of the boiler service.

Service Interval Timer

Fig. 15

Commissioning Instructions

If the thermostat and the receiver have been supplied together in a combined pack, the

units have been paired in the factory and no commissioning is required (RX1 only).

To tune the RX receiver to the frequency of the thermostat signal, follow steps 1-5 below.

Step 1

TP5000-RF Si - Reset the unit by pressing the recessed reset button.

Step 2

Press and hold V and + buttons (ﬁg. 13) for 3 seconds (TP5000 RF Si now transmits unique signal

continuously for 3 minutes).

Step 3

RX1 - Press and hold buttons PROG and CH1 for 3 seconds until green light ﬂashes once.

(Fig. 14)

Step 4 (Fig.14)

RX2 (if applicable)

Stat 1 - perform steps 1-3 and 5.

Stat 2 -perform steps 1-2 and then press PROG and CH2 on RX2.

RX3 (if applicable)

Stat 1 - perform steps 1-3 and 5.

Stat 2 - perform steps 1-2 and then press PROG and CH2 on RX3 then step 5.

Stat 3 - perform steps 1-2 and then press PROG and CH3 on RX3.

Step 5

TP5000Si-RF - Press V or Λ to select temperature - the unit will revert back to operating mode.

IMPORTANT RF Models only

To ensure that the factory programmes are set and the micro-computer is operating correctly

it is essential that you press and hold the RESET button before you begin any commissioning or

programming.

Fig.13

Fig.14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Danfoss TP5000 Si Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info