Bedienungsanleitung Definitive Technology Mythos 1 (Seite 6 von 6) (Englisch)

582226

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

6 7

Hooking Up Your Mythos Loudspeakers

Your Mythos loudspeakers each have one pair of gold 5-way

binding posts. Normally, you will hook up the left main/front channel

red(+) terminal of your receiver or ampliﬁer to the red(+) terminal of

your left Mythos loudspeaker and the left main/front channel black(-)

terminal of your receiver or ampliﬁer to the black(-) terminal of your

left Mythos loudspeaker. Connect the right channel main/front chan-

nel red(+) terminal of your ampliﬁer or receiver to the red(+)

terminal of your right Mythos loudspeaker and the black(-) terminal

of the right main/front channel of your receiver or ampliﬁer to the

black(-) terminal of your right Mythos loudspeaker.

If you are using the Mythos as side/rear surround speakers, hook

up the left surround red(+) terminal of your receiver or ampliﬁer to

the red(+) terminal of your Mythos left surround speaker and the left

surround black(-) terminal of your receiver or ampliﬁer to the black(-)

terminal of your Mythos left surround speaker. Connect the right

surround red(+) terminal of your ampliﬁer or receiver to the red(+)

terminal of your Mythos right surround loudspeaker and the black(-)

terminal of the right surround channel of your receiver or ampliﬁer

to the black(-) terminal of your Mythos right surround loudspeaker.

If your receiver/ decoder has a bass management system and you

are using a separate subwoofer,set bass management to “Small”left

and right main speakers, “Small”center channel, “Small”surround

speakers and “Yes”subwoofer. If your receiver/decoder has a choice

of crossover frequencies, set the crossover to 80 Hz. If you are not

using a separate subwoofer, set bass management to “Large”left

and right main speakers, “Large”center channel and “Large”surround

speakers, and “No”subwoofer.

Connecting Your Mythos Loudspeakers Setting Bass and Treble Controls on Your

Receiver or Ampliﬁer

Normally we recommend that you set the Bass and Treble controls

on ﬂat or 0 dB. This will give you the most linear and natural sound.

Also, if your ampliﬁer or receiver has a graphic equalizer, we recom-

mend that you leave it ﬂat. The reason for this is that we have spoken

with many consumers about what they thought were improperly

sounding speakers when, in fact, the problem was misadjusted tone

controls. When in doubt, leave them ﬂat; this almost always

sounds the best.

Usually if distortion is heard when the speakers are being driven

at loud levels, it is caused by driving (turning up) the ampliﬁer too

loud and not driving the speakers with more power than they can

handle. Remember, most ampliﬁers put out their full-rated power

well beforethe volume control is turned all the way up! If your

speakers distort when you play them loud, turn down the ampliﬁ-

er or get a bigger one.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Definitive Technology Mythos 1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info