Bedienungsanleitung Denon MC4000 (Seite 7 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

614620

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

4. Split Cue: When this switch is in the On position, the headphone audio will be “split” such

that all channels sent to cue channel are summed to mono and sent to the left headphone

channel and the master mix is summed to mono and sent to the right channel. When the

switch is in the Off position, the cue channel and master mix will be “blended” together.

5. Mic EQ: Turn these knobs to boost or cut the high and low frequencies for the

corresponding microphones.

6. Mic Echo Level: Turn this knob to adjust the amount of the reverb effect on the

microphones’ audio signal.

Rear Panel

1. Power Input: Use the included power adapter (5 VDC, 3 A, center-positive) to connect this

input to your power source.

2. Cable Restraint: You can secure cables to this restraint to help avoid disconnecting them

accidentally.

3. Power Button: Press this button to power MC4000 on or off. Power on MC4000 only after

you have connected all of your input devices and before you power on your amplifiers and

loudspeakers. Power off your amplifiers and loudspeakers before powering off MC4000.

4. USB Port: Use a standard USB cable (included) to connect this USB port to an available

USB port on yoru computer. This connection sends and receives audio and control

information to and from the computer.

5. Master Outputs (XLR, balanced): Use standard RCA cables to connect these outputs to

loudspeakers or an amplifier system. Use the Master knob on the top panel to control the

volume level.

6. Master Outputs (RCA, unbalanced): Use standard RCA cables to connect these outputs

to loudspeakers or an amplifier system. Use the Master knob on the top panel to control

the volume level.

7. Stereo/Mono: Use this switch to set the channel configuration of the Master Outputs:

Stereo (binaural audio using separate left and right channels) or Mono (summed monaural

audio through both left and right channels).

8. Booth Outputs (1/4” / 6.35 mm): Use standard RCA cables to connect these outputs to

booth monitors or a booth amplifier system. Use the Booth knob on the top panel to

control the volume level.

9. Aux Inputs: Use standard RCA cables to connect these line-level inputs to an external

audio source (smartphone, tablet, media player, etc.). Use the Aux knob on the top panel

to control the volume level.

10. Mic 1 Input (XLR or 1/4” / 6.35 mm): Use a standard XLR or 1/4” (6.35 mm) cable (not

included) to connect a standard dynamic microphone to this input. Use the Mic 1 Volume

knob on the top panel to control the volume level.

11. Mic 2 Input (1/4” / 6.35 mm): Use a standard 1/4” (6.35 mm) cable (not included) to

connect a standard dynamic microphone to this input. Use the Mic 2 Volume

knob on the

top panel to control the volume level.

12. Kensington

Lock: Use this slot to secure MC4000 to a table or other surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon MC4000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info