Bedienungsanleitung Denon PMA-1510AE (Seite 13 von 17) (Englisch)

498788

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

ENGLISH

Getting started

Basic connections Basic operation Troubleshooting Speciﬁcations IndexAdvanced connections Advanced operation Explanation terms

Connecting P.DIRECT jacks

If you use a preampliﬁer, connect it as shown below, and then you

can use this unit as a power ampliﬁer.

• Switching <POWER AMP DIRECT> “hON”, allows the device

connected to the Power Amp Direct connector on the rear panel to

be played. When ON, the input indicator turns off.

• Switching <POWER AMP DIRECT> “jOFF”, allows the program

source selected using the INPUT SELECTOR knob to be played.

When OFF, the input indicator lights up.

For details on operations of the preampliﬁer, refer to the instruction

manual supplied with the preampliﬁer to be used.

w qw q

(R) (L)

Pre-ampliﬁer

To PRE OUT jacks

Speaker

(L)

Speaker

(R)

NOTE

• When the <POWER AMP DIRECT> switch is “hON”, adjustment

of the volume, balance and tone on the main unit has no effect.

Adjust the volume on the input device.

• When the <POWER AMP DIRECT> switch is “hON”, the main unit

outputs at maximum volume. Check the output level on the input

device before playing it and adjust the volume accordingly.

Connecting pre out jacks

If you use a power ampliﬁer or subwoofer, connect it as shown

below, and then you can use this unit as a preampliﬁer.

For connecting speaker systems, refer to the instruction manual

supplied with the power ampliﬁer to be used.

Power-ampliﬁer

To input jacks

NOTE

• NEVER insert the short-circuiting pin plug into the PRE OUT

terminals. Doing so could result in damage.

• Signals are output from the PRE OUT terminals even when using

headphones.

Advanced connections

Setting Eco mode

With the Eco mode ON, this unit will automatically enter the standby

mode after about 30 continuous minutes of no output from the

speakers or headphones. During standby mode with the Eco mode

ON, the Power indicator is unlit to reduce power consumption.

Press and hold [AMPLIFIER POWER] on the remote

control for at least 5 seconds.

• Eco mode is switched between On and Off.

• The Power indicator indicates Eco mode On/Off during Standby, as

shown below.

Eco mode “Off”

“Lit in red”

Eco mode “On”

“Unlit”

• The Power indicator ﬂashes in red during Eco mode setting.

• If you set the Eco mode while the unit is ON, the unit will enter the

standby mode as soon as the Eco mode setting is completed.

• The default setting for the Eco mode is OFF.

NOTE

If a source other than that selected with INPUT SELECTOR is

selected with <REC OUT SELECTOR>, this unit does not enter the

standby mode.

This unit enters the standby mode if it detects no output from

the source selected with INPUT SELECTOR. Therefore if a source

not selected with INPUT SELECTOR is output from the REC OUT

terminals, the function of automatically entering standby mode is

disabled to avoid interruption of power during recording.

Advanced operations

Advanced connections Advanced operation

1.PMA1510AEE2_ENG_002_5th_0222.indd 9 2010/02/23 15:55:18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon PMA-1510AE Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info