684802
3
Zoom out
Zoom in
Vorherige Seite
1/5
Nächste Seite
4. In the alarm setting mode, press the ALARM 1/ ALARM 2 repeatedly to cycle through
the setting options:
Alarm hour time > alarm minute time > Alarm frequency (see note 1) > Alarm
sound source (see note 2) > Light intensity
Press the FORWARD button to adjust the values in each setting option. Press and hold
the button to change the values quickly.
Press the ALARM 1/ALARM 2 button to confirm each setting option.
Once settings are done, the alarm is enabled and the corresponding AL 1/ AL 2
icon will show
Note:
1. In the alarm frequency setting, you can select the following:
1-5 = Monday to Friday, 1-7 = Everyday, 6-7 = Weekend only, 1, 2, 3, 4, 5, 6 or 7 =
Once a week only (on the selected day)
2. Select the buzzer (“bu” shows on the display), the radio (the last played radio
frequency shows on the display), or nature sound (“nS” shows on the display) as the
alarm sound source.
All alarm sound sources will increase their volume gradually when the alarm sounds.
If the radio is selected as the alarm sound source, you are prompted to select the radio
maximum volume when the alarm sounds.
If the nature sound is selected as the alarm sound source, you are prompted to select
the type of nature sound and then the maximum volume when the alarm sounds.
Alarm wake-up light
The wake-up light can be set at a light intensity level from L01 to L20 or off. If a light
intensity level from L01 to L20 is set, the light will switch on at its lowest intensity 30
minutes before the set alarm time.
The light will then gradually increase to the set maximum brightness until the alarm
goes off. For example, if the alarm is set for 8:30 with a light intensity of L10, the light
will switch on at 8:00 at the lowest level (L01) and gradually increase to the light level
L10 at 8:30.
The light will not turn on if the alarm is set less than 30 minutes before the set time.
Turning the alarms on or off
When the clock time is displayed, press and hold the ALARM 1 or ALARM 2 button to
enable or disable the respective alarm. The corresponding alarm icon (AL1/ AL2) will
switch on when the alarm is enabled.
Deactivating a sounding alarm
Press the LIGHT ON/OFF button to temporarily silence the alarm (snooze) and then
press the ALARM OFF button to switch off a sounding alarm.
When the alarm sounds, the corresponding alarm icon (AL1 or AL2) flashes on the
display.
The alarm will continue sounding for 30 minutes if no button is pressed. Then it will
stop automatically until the same time next day.
Sleep
This sleep function defines the duration of time before the radio switches itself off
automatically.
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Denver CRL-350 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Denver CRL-350

Denver CRL-350 Bedienungsanleitung - Deutsch - 5 seiten

Denver CRL-350 Bedienungsanleitung - Holländisch - 5 seiten

Denver CRL-350 Bedienungsanleitung - Französisch - 5 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info