Bedienungsanleitung DESQ 70240 Laminator (Seite 3 von 8) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

666844

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Anzahl der Walzen: 2 Hot Rollers

Max. Durchlassbreite (mm): 230 / A4

Vorheizzeit (min): 2-3

Folientaschendicke (micron): 250 (2x125)

Mit Anti Blokierung Schalter

Rodillos: 2 Rodillos caliente

Ancho máximo de plastificado: 230 / A4

Tiempo de esoera (min.): 2-3

Grosor máximo fundas (micras): 250 (2x125)

Sistema Antibloqueo

Operation instruction

OPERATION INSTRUCTION

1. Connect power cord to appropriate power source. Make sure that the hot/cold button (5) is set correctly. Rotate the

switch (4) into the desired micron setting (80-125). For cold lamination, ALWAYS place switch (4) to 125 mic. Choose 125

micron when laminating with 100 micron pouches.

2. When the laminator reaches laminating temperature, the indicator READY (3) becomes green.

3. Centre the item to be laminated into a laminating pouch (Figure 2), so that the borders are even on all the sides.

The suggested margin between the content and the sealed edge is no larger than 3 mm;

the suggested margin in the left, right, and the open end is larger than 3 mm (Figure 3).

4. The material that is to be laminated, is not allowed to be thicker than 0.5 mm including the film.

5. Insert the pouch with the item, sealed-edge first, straight into the laminator inlet (1). Hold the pouch until the machine

pulls it in.

6. The laminated item will automatically exit the outlet (2) of the pouch laminator. After the pouch has stopped moving,

the pouch can be removed.

7. If you finish the laminating, move the switch (4) to “off” position.

PRECAUTION

1. If the laminator is turned on and has not been used for more than an hour, excessive heat may have

created in the machine. To avoid overheating and its consequent inferior laminating result, insert a piece

of copy paper into the machine to remove the excessive heat before your formal laminating.

2. As soon as the lamination of the picture is finished, remove the laminated picture immediately to prevent the pouch from

curling due to overheating.

3. If white spots appear on the laminated pictures, it means the temperature is not high enough. Turn the front end behind

and insert the picture into the machine to laminate one more time.

4. The picture has to be laminated on both sides. One side lamination is prohibited to prevent film from being rolled into

the machine.

5. DO NOT insert the open end of the pouch into the machine to prevent it from being rolled into the machine.

6. There are vent holes in the bottom of the laminators. Make sure the holes are not fully covered when

the machine is operated to avoid overheating.

7. It is recommended to switch off the machine for 30 minutes, after it has been operating for a period of approximately

2 hours.

8. Only activate the pouch thickness switch when the appliance is switched on.

CARE AND MAINTENANCE

1. If the pouch is rolled into the laminator or break down, send your machine to your servicepoint for repairing. DO NOT

open the housing of the machine.

2. Unplug the machine while it is being wiped. Clean the machine with a slighly moist, soft cloth. Do not use a wet cloth or

any caustic or abrasive cleaning agents while doing so.

IMPORTANT SAFEGUARD

1. The unit is intended for indoor use only.

2. Do not drop the machine or put any object on top of it to avoid the housing to break. If it happens, unplug the laminator.

3. The pouch laminator must be connected to a supply voltage corresponding to the electrical rating of the machine as

indicated.

4. Children have to be attended by adults while using the machine; to protect the children from being burnt of shocked.

5. If the laminator smells burning, unplug the machine immediately and contact the service representative.

6. Unplug the laminator before it is moved, or when it is not in use for an extended period of time. When using the

laminator for an extended time, turn off the machine for an hour for every other eight hours.

7. Do not place the laminator near a heat generating object like furnaces or radiators.

8. The machine and the power cord should be away from water to avoid electrical shock.

9. Place unit on a secure, stable area to prevent the machine falling and possibly causing personal injury and damage to the

unit.

10. If the supply cord is damaged, it must be replaced by the manufacturer or its Service Agent or similarly qualified person

in order to avoid a hazard.

SOLVING A JAM

Turn the power of the laminator by turning the switch (4) to ABS. Let the machine cool down briefly (for hot laminating).

Hold the switch firmly on ABS mode with one hand and pull out the film completely from the machine’s insert or outlet

opening with the other hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DESQ 70240 Laminator Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info