Bedienungsanleitung DeWalt DWH052K T 1 (Seite 2 von 6) (Englisch)

549676

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

TO REMOVE FLAT CHISEL (FIG. 8–11)

1. Pull adaptor (B, C, D) down as shown.

2. Remove flat chisel (U) from tool holder as instructed in the tool instruction manual.

2. Open latch (I) and slide dust extraction system (A) from tool holder.

3. Remove adaptor (B, C, D).

Attach Dust Extraction System To Dust Extractor Vacuum

(Fig. 1, 12, 13)

WARNING: Use only power tools recommended by DEWALT with this attachment. For more

information about D

EWALT power tools compatible with this attachment, please contact your

local dealer, call 1-800-4-D

EWALT (1-800-433-9258) or visit our website www.dewalt.com.

Push dust extractor vacuum hose nozzle (P) into connection point (H) until tight. For a more

secure connection use the AirLock connection system.

NOTE: Ensure hose connection is secure.

AIRLOCK CONNECTOR SYSTEM - DWV9000 (SOLD SEPARATELY)

AirLock allows for a fast and secure connection between the dust extraction system and the

dust extractor vacuum.

1. Ensure the collar (Q) on the AirLock connector (M) is in the unlock position. Align notches

(R) on collar and AirLock connector as shown for unlock and lock positions.

2. Push the AirLock connector (M) onto the connection point (H) of the dust extraction

system (A).

3. Rotate the collar (Q) to the locked position. NOTE: The ball bearings (N) inside collar will lock

into slot (O) and secure the connection.

The dust extraction system is now securely connected to the dust extractor vacuum.

OPERATION

WARNING: ALWAYS turn off tool and disconnect the tool from the power source

before making any adjustments or removing or installing attachments or accessories.

This applies to both the chipping tool and the dust extractor vacuum. Such preventative

safety measures reduce the risk of starting the tool accidentally.

WARNING: For your own safety, read the instruction manual for both the chipping tool and

the dust extractor vacuum before using any accessory. Failure to heed these warnings may

result in personal injury and serious damage to the tool and the accessory. When servicing this

tool, use only identical replacement parts.

CAUTION: DO NOT carry or guide the tool by the dust extractor vacuum. Hold the tool as

instructed in the tool instruction manual.

• Ensure latch is securely closed.

• Ensure rotary function is disabled and that the hammerdrill is set to chiselling/rotary stop

mode.

NOTE: The amount of dust retained by the dust extractor vacuum is dependent on its filter

system. Refer to the dust extractor vacuum instruction manual for more information.

1. Turn the dust extractor vacuum on as instructed in the dust extractor vacuum instruction

manual.

2. Switch on the hammerdrill as instructed in the tool instruction manual.

NOTE: The two larger dust shrouds have bellows (T, Fig. 14) to increase flexibility when

working in tight or confined spaces.

MAINTENANCE

WARNING: ALWAYS turn off tool and disconnect the tool from the power source

before making any adjustments or removing or installing attachments or accessories.

This applies to both the chipping tool and the dust extractor vacuum. Such preventative

safety measures reduce the risk of starting the tool accidentally..

Your chipping dust extraction system has been designed to operate over a long period of time

with a minimum of maintenance. Continuous satisfactory operation depends on proper tool care

and regular cleaning.

TROUBLESHOOTING

FAULT POSSIBLE CAUSE REMEDY

Excessive dust

emission

dust extractor vacuum is full empty the dust extractor vacuum

suction channel is blocked clean the suction channel

The chisel is extended more

than 4.9" (125 mm)

use a shorter chisel or a longer dust

shroud

Dust Extraction

System does not

attach to hammer

the dust extraction system is

not assembled correctly

Refer to Assembly section.

adaptor and tool holder are

oily or greasy

remove oil and grease with a clean cloth

the locking latch is damaged replace locking latch

wrong adaptor being used select the correct adaptor

Cleaning

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested

with this product, use of such accessories with this tool could be hazardous. To reduce the risk

of injury, only D

EWALT recommended accessories should be used with this product.

If you need assistance, please contact DEWALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

EWALT (1-800-433-9258) or visit our website www.

dewalt.com.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be

performed by a D

EWALT factory service center, a DEWALT authorized service center or other

qualified service personnel. Always use identical replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date of purchase. This warranty does not cover part failure due to normal

wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-D

EWALT (1-800-433-9258). This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights which vary in certain

states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your D

EWALT Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt

for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, see country specific warranty information contained either in the

packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-4-D

EWALT (1-800-433-9258) for a free replacement.

FIG. 1

FIG. 2

J, U

E, F, G

FIG. 3

B, C, D

FIG. 6

FIG. 7

FIG. 4 FIG. 5

J, U

4.9" (125 mm)

1.2" (30 mm)

DeWalt DWH052K T 1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DWH052K T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info