Bedienungsanleitung Dexford RCT 170 (Seite 15 von 16) (Deutsch, Englisch, Französisch, Italienisch)

585376

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Setting the alarm time

You can programme 2 different alarm times in the radio−controlled clock.

1. Press and hold the Mode button (7) until Alarm 1 or Alarm 2 appears in the display.

2. Press and hold the Mode button (7) for 3 seconds (hour digits flash).

3. Use the Up/Down buttons (6/5) to set the required hour and confirm the selection by pressing the Mode button (7).

4. Use the Up/Down buttons (6/5) to set the required minute.

5. Press the Mode button (7) to confirm the setting and activate the alarm time.

Note! If you do not complete any input for a setting for 30 seconds, the process is cancelled and the clock returns

to the Alarm 1 or Alarm 2 display.

Switching the alarm on/off

1. Press the Alarm button (3) to switch the alarm function settings in the following cycle: Alarm 1 activated, Alarm 2

activated, Alarm 1 and Alarm 2 activated, Alarm 1 and Alarm 2 deactivated.

2. When the alarm time activated is reached and the alarm goes off, press the Light/Snooze button (1) to interrupt the

alarm for approx. 5 minutes before it continues again.

3. Press the Alarm button (3) to switch the alarm off, whereby it is switched off permanently for Alarm 2 or switched off

until the same time the next day for Alarm 1.

Note! If you do not press the Alarm button (3) or Light/Snooze button (1), the alarm is automatically switched off

after 4 minutes.

Setting the foreign time

In addition to setting the local time, you can also set the time of a location abroad and switch the display between the two

times.

1. Press and hold the Up button (6) for 3 seconds when the default display is shown. The foreign time display appears

together with an F".

2. Press and hold the Mode button (7) for 3 seconds (hour digits flash).

3. Use the Up/Down buttons (6/5) to set the required hour and confirm the selection by pressing the Mode button (7).

Note! If you do not complete any input for a setting for 30 seconds, the process is cancelled and the clock returns

to the foreign time display.

4. Press and hold the Up button (6) for 3 seconds when the foreign time display appears. The default display reappears

and the F" disappears. You can switch between default display and foreign time display at any time.

Back−lighting

Press the Light/Snooze button (1) to switch on the back−lighting for 5 seconds.

Changing the time format

Press and hold the Up button (6) when the default display is shown in order to switch between the 24−hour and 12−hour

time format (AM/PM).

Radio signal reception

The clock attempts to synchronise with the DCF signal every hour. You can also initiate reception of the DCF signal

manually by pressing and holding the Temperature button (4) for 3 seconds. The reception indicator (12) appears in the

display during the process.

Possible sources of interference for radio signals

D Domestic household equipment without RFI suppression

D TV sets less than 2 m away

D Machines producing HF stray fields (high frequency)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dexford RCT 170 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info