WSR
Desktop Weather Station
Introduction
This desktop weather station comes with weather forecasting capabil-
ities, clock, calendar
ered by the supplied
batteries. It is recommended to use the
1 [ SNOOZE / LIGHT
2 Base
3 [
4 [ +/C/F ] button
5 [ HIST
6 [ MODE ] button
7 [ CHANNEL
8 [ -/RCC ] button
9 [ MAX/MIN ] button
10 Battery
1 AC-DC in jack
Getting started
It is recommended to set up the remote temperature sensor before
setting up the weather station / clock. See "Configuring Remote T
perature Sensor(s)" below for more information.
Installing the AC/DC adapter
1. Remove all "AAA“ batteries before plugging in
necessary
2. Plug in
3. Connect
power adapter plug is not obstructed by furniture or such. For
safety reasons, only use the power adapter plug supplied.
Batteries installation (optional)
1. Open battery compartment (10) on the back of the unit.
2. Install / replace with 3x "AAA" size batteries in the compartment. lt
is recommended that only alkaline batteries are used.
3. Replace the battery compartment cover (10) on the back of the unit.
4. A
Batteries safety warnings
1. Please read all instructions carefully before use.
2. Install batteries correctly by matching the polarities (+/-).
3. Always replace a complete set of batteries.
4. Never mix used and new batteries.
5. Remove
6. Remove batteries when not in use.
7. Do not recharge and do not dispose of batteries in fire as the bat-
teries may explode.
8. Ensure batteries are stored away from metal objects as contact
may cause a short circuit.
9. Avoid exposing batteries to temperature or humidity extremes or
direct sunlight.
10. Keep all batteries out of reach from children. They are a choking
hazard.
1 Please retain packaging for future reference.
Setting up the weather station
The weather station will beep once when batteries are installed or the
AC/DC adapter is plugged in.
1. The double digits will flash showing the level of your location above
sea level at the bottom right hand corner of the display
Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to change your unit
location level above sea level. The sea level units are in meters (1
meter equals approximately 3.28 feet). Contact your local weather
bureau or authorities for more information if required.
2. Press [ HISTORY
sea level.
3. Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to change the cur-
rent weather situation of your location. See figure below for the
weather pattern that best resembles your immediate area.
4. Press [ HISTOR
Interpreting the weather forecast symbols
1. The weather station requires at least 24 hours to acclimatise to
local weather conditions. The weather station will process and
analyse the weather patterns of the past 24 hours in order to deter-
mine the future weather
accurately reflect the actual weather for your immediate area till 24
hours have elapsed.
2. The weather station will display the symbols (see above) to indicate
the predicted weather forecast for the next 12 to 24 hours for an
area within a radius of approximately 30-50 km.
Note:
1. The weather forecast is only for reference and only for domes-
tic use. Do NOT rely on the weather station for a forecast for
any serious matter including but not limited to: personal health,
any business or financial decisions, and/or agricultural plan-
ning.
2. The weather forecast does not display the current weather
displays future weather situation.
Adjusting the weather station
1. Press [ HISTORY
2. Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to select between
atmospheric pressure units of pascal (hPa) to inch of mercury
(inHg).
3. Press [ HISTORY
4. Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to select between
absolute and relative atmospheric pressure.
5. Press [ HISTORY
6. Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to change your unit
location level above sea level.
7. Press [ HISTORY
sea level.
8. Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to change the cur-
rent weather situation for your location. See above for the weather
pattern that best resembles your immediate area.
Barometer
The unit takes approximately 24 hours to process and analyse the
recorded barometric pressure data. Prior to 24 hours, the pressure trend
and weather forecasts may not reflect actual weather forecast for your
area.
Reading pressure trend
Recorded memory of the barometric pressure changes are displayed
with 3 arrows to show pressure trend.
Note: It is only possible to measure the barometric pressure trend prop-
erly when the unit remains at the same altitude location. When moving
around at different altitudes within a short period of time, the air pressure
and the barometric pressure will change. The pressure trend will only be
correct and regular if the unit remains at a constant location altitude
for 24 hours or more.
To recall recorded pressure history reading
The barometric pressure reading is recorded in hourly intervals and
can be recalled and displayed for the previous 12 hours.
Press [ HISTORY
for the past hours. “-1 HR" indicates the pressure of the previous
hour
the current pressure reading returns.
To synchronize clock with RCC
1. Where available, this clock will automatically synchronize with
the radio control towers at the following time: 02:03, 03:03,
04:03, 05:03.
2. User may also manually synchronize the clock by following the
instructions below
3. Hold down the [ -/RCC ] button (8) for approximately 3 seconds
until is
4. When this signal is flashing, the clock is attempting to synchro-
nize with the radio control tower will flash when a
strong signal is received and the clock will synchronize with the
radio control tower
symbol will stop flashing and will be displayed once the signal
is received and is in synchronization.
5. The symbol will not be displayed if the clock is not able to syn-
chronize within this period of time. User may manually synchro-
nize again at a later time or the clock will automatically attempts
to synchronize at the above mentioned time.
6. Please note all other clock / weather station settings cease to
function when the clock is in RCC synchronization mode. Wait
until the clock is no longer attempting to synchronize or it is syn-
chronizing to set other clock and weather station functions.
7. lf the alarm goes off during synchronization mode, RCC synchro-
nization will cease immediately
again to set synchronization.
RCC Zone Offset
This clock is equipped with radio controlled time adjustment. The user
will need to work out the time zone signal they receive at their current
location and make (any) adjustment as required.
This function also allows for daylight saving adjustment. Contact your
local weather bureau or authorities for more information.
1. Press the [ -/RCC ] button (8) once for +1 time zone.
2. Press the [ -/RCC ] button (8) once again for +2 time zone.
3. Press the [ -/RCC ] button (8) once again for -1 time zone.
4. Press the [ -/RCC ] button (8) once again for same time zone.
To set time manually
1. Hold down the [
onds until the display is flashing.
2. Press [ +/C/F ] button (4) or [ -/RCC ] button (8) to change the
hour setting. Press [
