Bedienungsanleitung Dimplex Cadiz ROF2T (Seite 5 von 8) (Englisch)

798036

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Boost Heat Setting ‘ ’ – This switch as shown in Fig.’s 2, 3

& 4 provides the boost heat output. When it is activated a neon light ‘x’

illuminates below the control button.

Note – With the 3 selector switches activated the maximum output of

this radiator can be achieved.

Manual Timer Operation - see ‘y’ in Fig. 3

(ROF2TI models only)

Set the I - - slide switch on the timer (Fig. 6) to :

Position - Heating Off

Position I - Manual operation

This setting allows power to the heater uninterrupted by the timer

settings. The heat selector switch will control the output (see ‘Controls’).

Position - ‘Auto’ operation

DO NOT disconnect this heater from the mains supply unless it is being

taken out of use (e.g. in summer or for storage), otherwise the timer

clock will stop.

Setting the time of day

To set the time of day, rotate the timer dial clockwise (indicated by the

arrow) until the correct time of day is opposite the reference mark

(see Fig. 6). The 24-hour clock is used ; e.g. time shown for 4 pm is ‘16’

(16:00hrs).

Setting the ‘Auto’ ON and OFF times

To set the timer :

1. Using your finger tip or the tip of a pencil, push in as many segments

as necessary around the dial, according to the times you don’t require

heat – see Fig. 7. Each segment pushed in switches the heater OFF for

that part of the hour. All other segments will be ON. For example, Fig. 9

shows the timer set to switch the heater ON between 9.00am and 4.00pm

and between 9.30pm and 7.00am.

2. You can select as many ON periods as you like, within the 24-hour

day. The settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’ segments

you wish to cancel and pull out new ‘ON’ segments as required.

Switching to auto

Set the heat selector and thermostat for the heat output required.

Check that the clock shows the correct time of day. Set the I - -

slide switch to (see Fig. 8) - the heater will switch ON and OFF

according to the timer settings (see Fig. 9).

IMPORTANT NOTES

Remember to observe all safety warnings when operating the heater on

auto setting unattended or attended .

If the mains supply to the heater is interrupted, the timer clock will stop

until power is restored ; reset the time of day to ensure correct ON and

OFF times.

Digital Timer Operation (see ‘z’ in Fig. 4 & Fig. 10)

IMPORTANT: Remember to observe all safety warnings when operating

the heater on auto setting, either attended or unattended.

The timer allows you to select ‘AUTO’ or ‘MAN ON’ by pressing the

‘MODE’ button until the required MODE appears at the bottom of the

timer display.

‘AUTO’ MODE allows the heater to switch ON and OFF according to a

set 24 Hour program period (see ‘Setting Programs’ section below).

‘MAN ON’ MODE allows power to the heater uninterrupted by the

program settings.

Key Lock:

If ‘ENTER’ and ‘MODE’ are pressed within 1 second, the keys will be

locked. The user will know the keys are locked as the lock symbol ‘ ’

will be displayed on the top left hand corner of the screen. To unlock the

keypad, press ‘ENTER’ and then ‘MODE’ within 1 second.

Initial Operation

For initial use, plug the heater into a regular household power point and

turn the power on. The timer is now ready to be set up for use.

Setting Current Time

1. Press the ‘PROGRAM’ button ONCE. The clock symbol appears

on the top left hand side of the screen. The user can now set the

clock.

2. The hour digit will flash. To adjust the hour use the ‘-‘ & ‘+’ buttons.

Confirm the hour digit by pressing ‘ENTER’.

3. Once ‘ENTER’ has been pressed the minutes will flash. To adjust the

minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit by pressing

‘ENTER’.

4. The timer now returns to the default display.

5. To reset incorrect time, repeat previous steps.

Once the correct time is set, a total of four ON/OFF time programs can

be set for operation.

Setting Programmes

Press the ‘PROGRAM’ key twice to set the programs.

You are now setting the programs starting with P1 ‘ON’.

SETTING P1 ON TIME:

1. To set the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by

pressing ‘ENTER’.

2. To set the minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit

by pressing ‘ENTER’.

Note: The minutes can only be set in 10 minute blocks in programme

‘MODE’.

SETTING P1 OFF TIME:

3. To set the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by

pressing ‘ENTER’.

4. To set the minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit

by pressing ‘ENTER’.

Repeat steps 1 to 4 to programme P2, P3 & P4. After programming P4

‘OFF’ you automatically exit to the default display.

At any time while programming the timer you can press the ‘PROGRAM’

button to exit to the default display.

Note: If the ‘ON’ time is the same as the ‘OFF’ time the appliance will

ignore the program.

The Advance Function

When in ‘AUTO’ MODE, if the ‘+’ button is pressed for longer than 2

seconds the programme will ADVANCE to the next setting programmed

and will only revert back to the program when the subsequent programme

time is reached. When the ‘ADVANCE’ function is running the ‘ADVANCE’

segment will be displayed on the LCD screen. If the ‘-‘ button is pressed

when the ‘ADVANCE’ programme is running the ‘ADVANCE’ feature

will be automatically cancelled and the programme will run as normal.

Note - Timer Memory Back Up Batteries - Once the heater has been

left plugged in with the socket switched on for at least 72 hours the

timer’s memory back up batteries will be fully charged.

Once the timer batteries are fully charged, if there is a power cut or

if the heater is disconnected from the mains for less than six months,

then the timer will continue to keep time & the settings in the memory

will remain intact.

If however the timer back up batteries have not been charged fully, or

if the heater is deprived of power for longer than six months, then the

time and the programme settings are likely to be lost and you may

therefore need to reset the time and the programme before using the

AUTO MODE again.

Dimplex Cadiz ROF2T Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dimplex Cadiz ROF2T

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info