Bedienungsanleitung Dolmar ES-2146 TLC (Seite 12 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599928

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

10. Take particular care when cutting in the vicinity of wire

fences. Do nut cut into the fence, as the saw may kick

back.

11. Do not cut into the ground.

12. Cut pieces of wood singly, not in bunches or stacks.

13. Avoid using the saw to cut thin branches and roots, as

these can become entangled in the chain saw. Loss of

balance presents a hazard.

14. Use a secure support (trestle) when cutting sawn

timber.

15. Do not use the chain saw to prise off or brush away

pieces of wood and other objects.

16. Guide the chain saw such that no part of your body is

within the extended path of the saw chain (see figure).

(Fig. 2)

17. When moving around between sawing operations,

apply the chain brake in order to prevent the chain

from being operated unintentionally. Hold the chain

saw by the front handle when carrying it, and do not

keep your finger on the switch.

18. Withdraw the mains plug when taking breaks or

leaving the chain saw unattended. Leave the chain

saw where it cannot present a hazard.

Kickback

1. Hazardous kickback may arise during work with the

chain saw. Kickback arises when the tip of the bar (in

particular the upper quarter) comes into contact with

wood or another solid object. This causes the

chainsaw to be deflected in the direction of the

operator. (Fig. 3)

2. In order to avoid kickback, observe the following:

• Never begin the cut with the tip of the bar.

• Never use the tip of the bar for cutting. Take

particular care when resuming cuts which have

already been started.

• Start the cut with the chain running.

• Always sharpen the chain correctly. In particular,

set the depth gauge to the correct height.

• Never saw through several branches at a time.

• When limbing, take care to prevent the bar from

coming into contact with other branches.

• When bucking, keep clear of adjacent trunks.

Always observe the bar tip.

• Use a trestle.

Safety features

1. Always check that the safety features are in working

order before starting work. Do not use the chain saw if

the safety features are not working properly.

– Chain brake:

The chain saw is fitted with a chain brake which brings

the saw chain to a standstill within a fraction of a

second. It is activated when the hand guard is pushed

forwards. The saw chain then stops within 0.15 s, and

the power supply to the motor is interrupted. (Fig. 4)

– Run-down brake:

The chain saw is equipped with an run down brake

which brings the saw chain to an immediate stop when

the ON/OFF switch is released. This prevents the saw

chain from running on when switched off, and thus

presenting a hazard.

–The front and rear hand guards protect the user

against injury from pieces of wood which may be

thrown backwards, or a broken saw chain.

–The trigger lockout prevents the chain saw from being

switched on accidentally.

–The chain catcher protects the user against injury

should the chain jump or break.

Transport and storage

When the chain saw is not in use or is being

transported, withdraw the mains plug and fit the

guide bar cover supplied with the saw. Never carry

or transport the saw with the saw chain running.

1. Carry the chain saw by the front handle only, with the

bar pointing backwards.

2. Keep the chain saw in a secure, dry and locked room

out of the reach of children. Do not store the chain saw

outdoors.

Maintenance

1. Withdraw the plug from the socket before carrying out

any adjustments or maintenance.

2. Check the power cable regularly for damage to the

insulation.

3. Clean the chain saw regularly.

4. Have any damage to the plastic housing repaired

properly and immediately.

5. Do not use the saw if the switch trigger is not working

properly. Have it properly repaired.

6. Under no circumstances should any modifications be

made to the chain saw. Your safety is at risk.

7. Do not carry out maintenance or repair work other

than that described in this instruction manual. Any

other work must be carried out by authorized service

centers.

8. Only use genuine replacement parts and accessories

intended for your model of saw. The use of other parts

increases the risk of accident.

9. We accept no responsibility for accidents or damage

should non-approved bars, saw chains or other

replacement parts or accessories be used.

First aid

Do not work alone. Always work within shouting

distance of a second person.

1. Always keep a first-aid box to hand. Replace any

items taken from it immediately.

2. Should you request assistance in the event of an

accident, state the following:

• Where did the accident happen?

• What happened?

• How many persons are injured?

• What injuries do they have?

• Who is reporting the accident?

NOTE:

Individuals with poor circulation who are exposed to

excessive vibration may experience injury to blood

vessels or the nervous system.

Vibration may cause the following symptoms to occur in

the fingers, hands or wrists: “Falling asleep” (numbness),

tingling, pain, stabbing sensation, alteration of skin colour

or of the skin.

If any of these symptoms occur, see a physician!

Dolmar ES-2146 TLC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dolmar ES-2146 TLC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info