Bedienungsanleitung Dolmar EV-3618 (Seite 7 von 19) (Englisch, Holländisch)

599936

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Vibration

People with poor circulation who are exposed to

excessive vibration may experience injury to blood

vessels or the nervous system. Vibration may cause

the following symptoms to occur in the ngers, hands

or wrists: “Falling asleep” (numbness), tingling, pain,

stabbing sensation, alteration of skin color or of the

skin. If any of these symptoms occur, see a physician.

To reduce the risk of “white nger disease”, keep your

hands warm during operation and well maintain the

equipment and accessories.

WARNING:

This machine produces an electromagnetic eld during

operation. It is recommended that persons with medical

implants should consult their doctors and implant

manufacturers before using this machine. Otherwise

the electromagnetic eld may affect medical implants

and it may result in serious injury.

ASSEMBLY

CAUTION:

Always be sure that the machine is switched off and

unplugged before carrying out any work on the tool.

Assembling the handle bar (Fig. 2, 3)

1) Fasten the lower handle bar (4) to the machine with

the knobs (11).

2) Place the upper handle bar (3) onto the lower handle

bar, and then fasten them with two spacers, nut, and

the lever (7).

3) Fasten the cord with the clips (8) onto the handle bar.

Assembling the grass catcher

CAUTION:

Do not operate the machine without grass catcher.

Otherwise ejected object may cause injury.

For rear discharge appliances with exposed rear rollers,

when used without a catcher, full eye protection shall

be worn.

NOTE:

The performance of the machine reduces when the

grass catcher is full. Empty the grass catcher on regular

basis before it becomes completely full.

Installing the grass catcher

Pull up the deector guard (10) and hold it. Insert hooks

on the grass catcher into the grooves on the machine.

Removing the grass catcher

Pull up the deector guard (10) and hold it. Remove the

grass catcher by releasing the hooks from the grooves

on the machine.

Cord strain relief (Fig. 4)

The cord strain relief (5) helps to prevent the cord from

entangling into the blade or wheel.

Make a small loop at the end of the mains cord, and pass

it through the opening of the cord strain relief, and then

hang it on the hook.

Always take the position of the cord into consideration

during operation. Start your operation from the nearest

point to the power supply to prevent the cord from

accidentally cut. It is recommended keeping the cord over

your shoulder during the operation.

•

Removing or installing cutting tool

CAUTION:

Wear protective gloves.

Pay particular attention when handling cutting tool. It is

very sharp and may become hot during operation.

Always use appropriate cutting tool in accordance with

your operation.

Before operation, make sure two bolts, which hold the

cutting tool onto the machine, are rmly tightened.

Do not use the machine if it is loose or missing. If it is

damaged, replace it immediately.

Removing cutting tool

1) Remove the grass catcher (9).

2) Remove the handle from the machine.

3) Place the machine upside down on a at surface.

4) Loosen the two bolts (14). Remove them and spring

washers.

5) Lift the bearing part of the cutting tool (15), and then

pull the cutting tool (13) out from the drive shaft (16).

Installing the cutting tool

1) Insert the cutting tool by sliding its hex nut part into the

socket of driving shaft.

2) Fasten the bearing part to the machine by the bolts

and spring washers.

FUNCTIONAL DESCRIPTION

WARNING:

Before plugging the machine, always make sure that

the machine is switched off. Plugging the machine with

the switch on may cause an unexpected start resulting

in serious personal injury.

Never use the machine if power cable is damaged.

Otherwise it may cause electric shock.

Do not use the machine if the switch does not turn it on

and off. Have defective switches replaced by Dolmar

authorized service center.

Start/stop lever

To start the machine, press and hold the lock-off button

(2), and then fully pull the start/stop lever (1) and hold it.

Once pulling the start/stop lever, you do not need to hold

the lock-off button.

To stop the machine, simply release the start/stop lever.

Handle angle adjustment

You can change the angle of upper handle bar.

1) Unlock the handle clamps (6).

2) Adjust the angle of the upper handle bar (3).

3) Lock the handle clamps again.

Height adjustment

Depending on the condition of the grass, adjust the height

of the cutting tool.

Refer to the table below as rough indication for depth

settings.

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar EV-3618 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info