Bedienungsanleitung Drayton miGenie Wish 1 - T714R (Seite 2 von 2) (Englisch)

653168

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Add and Remove Devices

(NB: only required if adding a new thermostat. All items in the Wish 1, 2 & 3 packs are pre-bound)

To manually connect a miGenie thermostat, insert the batteries into the thermostat and wait for “Bind?” to be

displayed, press ( ) to select. You will also need to enter the binding process on the miGenie Controller, by entering

the Advanced Settings menu, then the Zone settings and select the Device manager option. In this screen select

the Add thermostat option to complete the binding process. To remove a miGenie Thermostat enter the Device

manager option in the miGenie controller using the same sequence detailed above. The option will now display

Remove Thermostat, select this option and the thermostat will be removed from the system.

To manually connect a miGenie gateway, press and hold the button on the rear of the gateway for more than 5

seconds, the LED will repeatedly ﬂash red-yellow-green. You will also need to enter the binding process on the

miGenie Controller, by entering the Advanced Settings menu, then System settings, then Internet options. In this

screen select the Add gateway option to complete the binding process. To remove a miGenie Gateway enter the

Internet options menu in the miGenie controller using the same sequence detailed above. The menu will display

Remove gateway, select this option and the gateway will be removed from the system.

Technical Data

Step 7: Connection Charts

Step 8: Advanced Settings

→

Feature Description Factory Pre-Set

Device manager Add, replace or remove RF room thermostats Pre-bound

Signal strength Displays the signal strength of the selected zone, if a miGenie thermostat is connected to the zone

Channel settings (within

Zone settings)

Customise the application type and associated control settings for zones following this

application type

Application type Selecting the application type pre-conﬁgures

the available zone information

Zone 1: Heating:

Zone 2: Hot Water

Zone 3: Heating

Zone 4: Unused

Control type

*Heating zones only

Select TPI or TP.

TPI = Use if the house usually reaches setpoint in ≤ 1 hour.

TP = Use if the house usually reaches setpoint in ≥ 1 hour.

TPI

Cycle rate (only when

control type is TPI or TP)

Select 3 cph (cycles per hour), 6 cph or 12 cph 6 cph

Frost temperature Disable frost protection or set between 3-10°C 5°C

Valve protection The output will be activated for the speciﬁed time (in minutes). This

will happen weekly, related to the last action of the output. Select 0

to 10 minutes.

0 mins (Off)

Feature Description Factory Pre-Set

Advanced settings

! CAUTION! These settings should only be modiﬁed by a qualiﬁed person. They can inﬂuence the

safety and the proper functioning of the system

System settings These are settings applicable to the system controller unit, global settings

for bound nodes and internet connection settings

Backlight miGenie controller options are:

On with timeout, Always on, Always off

miGenie thermostat options are:

On with timeout, always off

On with timeout

Lock settings Enable or disable the screen lock for the miGenie controller. To lock:

enter a 3 digit code for protection. To unlock: enter the 3 digit code

000

Master code 401

Product Information View product details for devices in the system e.g. part number, ﬁrmware version, etc.

Signal strength Informs about the current signal strength of the products connected to the system

Internet options Sub-menu relating to the connection of an internet gateway – enables

a gateway to be added, replaced or removed with an indication of signal strength.

System reset Will reset all settings to factory pre-sets

Zone settings Customise each zone according to personal preferences

These are setting which will be applied to a connected thermostat

Select zone Select the zone for the following actions

Rename zone To rename an existing zone Heating, H Water, LivRoom

Edit schedule Update the schedule for the zone

Zone setup Contains detailed zone setup values – see below for descriptions

Minimum

temperature

The minimum set temperature that can be set

for the zone

5°C

Maximum

temperature

The maximum set temperature that can be set

for the zone

30°C

Eco

temperature

Temperature used for energy saving events

e.g. during the night

16°C

Comfort

temperature

Temperature used for comfort events

e.g. during the day

21°C

Offset

temperature

Adjust the displayed temperature to personal needs 0°C

! IMPORTANT:

Always switch off the mains before removing

the miGenie Controller – and never ﬁt it to a live

wall-plate!

→

Arrowed numbers relate to the junction box.

* Consult boiler handbook for details of pump

overrun wiring.

Make the wiring connections, as above, for the

appropriate system. For surface wiring, snap out the

cable entry strip on the bottom edge of the wall-plate.

miGenie controllers are double-insulated and need

no earth connection, but an earthing continuity (loop)

terminal is provided for convenience.

After wiring, clip on the unit and tighten the securing

screws. Check the mains input has a 3A fuse, and switch

on the mains.

Biﬂo system: Model T724R Twinzone system: Model T724R

From the Home screen, select

Settings, then Advanced settings

as shown.

From here you can edit the assigned zones, rename them if required

and check the Signal strength.

→

→ →

→

Client Invensys File Name 7549 Invensys miGenie Instructions 06490211001 IssC

Artworker -

Proof Stage

Finished Size 420x297mm

Creative Director Mike Lane Artwork % 100%

Modification Date 07/09/15 4:16PM Bleed 3mm

miGenie Controller

3 Zone system: Model T744R

miGenie Controller

Select a name from the list or

select 'Custom zone name' to

create a new zone name.

miGenie controller miGenie thermostat miGenie gateway

Power Supply 230V a.c. +10% -10% 50Hz 2 X 1.5V IEC LR6(AA) alkaline

batteries

5V d.c. 1A USB Micro-B

Switch Rating 2 (1) A 230V a.c. each switch N/A

Wiring Fixed wiring only, to comply with

current IET regulations (BS7671)

No wiring required

Battery life N/A 2 years typical N/A

Ambient Temperature

Operating: 0º to 45ºC (miGenie controller 3 / 4 channel 0º to 40ºC)

Storage: -20ºC to 55ºC

Ambient humidity

(non condensing)

Operating 25% to 90%

Storage 15% to 95%

Temperature Range 5 ºC - 30 ºC N/A

Control Accuracy <0.6ºC at 4º / hour N/A

Timing resolution 1 minute N/A

Temperature resolution 0.5°C N/A

Ball Pressure Test

Temperature

75ºC

Pollution Degree 2

Energy Class IV = 2% (Acc. EU 811/2013, 812/2013, 813/2013, 814/2013) N/A

Software Class A

Without Mains Power Display: blank; Time: always kept

Program times: always preserved

N/A

Rated Impulse Voltage 2.5kV N/A

Radio Frequency 868.3MHz (Bi-directional communication)

Radio Signal Range 30m typically. The range may be affected by the composition / density and the number

of walls between the miGenie products

Mounting Industry standard wall plate Wall bracket or table stand Table top

Relevant EC Directives: 2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic Compatibility Directive

1999/5/EC R&TTE Directive

2013/56/EU Battery Directive

2011/65/EU RoHS Directive

Applied Standards: EN60730-1; EN60730-2-7; EN60730-2-9

EN 300 220-2; EN 301 489-3

Drayton miGenie Wish 1 - T714R Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Drayton miGenie Wish 1 - T714R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info