749776
3
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
-3-
INTRODUCTION
Dear customer,
You have chosen to purchase a DREAMLED Solar LED Wall Light SLWL-200+. We
thank you for this purchase and hope that your experiences with this quality product
will be pleasant ones. Prior to using this product, you should carefully read these user
instructions so that you can then install and operate your SLWL-200+ accordingly.
Please keep these user instructions so that you can reference them later on.
SOLAR PANEL
The SLWL-200+ is a Solar outdoor light with motion sensor. The solar panel acts as
the major energy source: it converts sunlight into electricity and recharges the internal
battery. Please note that when installing the lamp, the solar cells require as much
DIRECT SUNLIGHT as possible (at least 5~7 hours). The longer the solar cells are
exposed to direct sunlight, the longer the lamp will stay ON during the night.
MOUNTING LOCATION
When the lamp is in a location that receives less sunlight, it will operate for fewer hours
per night. Night lighting time can also vary depending on how bright the sky is on any
given day.
Insu󰀩cient charging of the battery will a󰀨ect performance and may result in the fact that
the lamp goes o󰀨 before dawn because the battery was not fully charged.
The solar panel is best directed as much as possible towards the south in order to
maximize exposure to direct sunlight. Please note that the four di󰀨erent seasons (and
the sun’s angle in these 4 periods) can a󰀨ect the lighting time of the lamp.
Select a location that is not located close to other light sources, such as for example
street lighting, because this enables the lamp to be switched o󰀨 automatically.
Maximum lighting time depends on sunlight and daytime charging. Min. charging time
is 5~7 hours in direct sunlight.
INSTALLATION
Use the measure card to mark the screw positions.
Drill the wall and screw the lamp onto the wall using the supplied
wall plugs and screws
Choose a stable, solid and supportive surface and make sure
the lamp is mounted faced towards the sun. Mounting height is
2~4 meters. Leave at least 5 mm of the screw above the surface
hatch to x the lamp properly.
This lamp is intended only for outside use.
MOTION SENSOR RANGE
One motion sensor can be used in
a range of max. 10 meters. Actual
range of the motion detection
sensor depends on mounting
height as shown in the illustration.
GB
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DreamLED SLWL-200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info