Bedienungsanleitung Dremel 2200 Versaflame (Seite 5 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

488612

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ASSEMBLY

WARNING

ALWAYS SWITCH OFF THE TOOL AND

ALLOW IT TO FULLY COOL DOWN BEFORE

ATTACHING OR REMOVING ACCESSORIES.

GENERAL

The Dremel VersaFlame is a high quality tool that can be used

for hard or soft soldering. It can also be used to heat up and/or

ignite ﬂammable and non-ﬂammable materials. The Dremel

VersaFlame emits an adjustable ﬂame with a temperature of up

to 1200°C. It has an integrated ignition mechanism.

FIGURE 1

1. Soldering tip

2. Catalyst

3. Burner

4. Air control lever

5. Ignition button

6. Child safety lock (stopper)

7. Lock button (for continuous working)

8. Flame control lever

9. Gas tank

10. Base

11. Filling valve

12. Flame extension piece

13. Deﬂector

(RE)FILLING THE GAS TANK

The Dremel VersaFlame may only be ﬁlled and operated with

liquid butane gas. Make sure the gas you are using is reﬁned

butane gas that can also be used for lighters.

1. Hold the tool and the gas reﬁll container as shown in

Figure 2.

2. Fill the gas tank with liquid butane gas observing the

instructions on the reﬁll container. The gas tank is full when

liquid butane gas escapes through the ﬁlling valve. In that

case, there is no more air present in the gas tank.

WARNING

DO NOT OVERFILL THE GAS TANK!

GETTING STARTED

USE

Familiarize yourself with the components of the Dremel VersaFlame

(see Figure 1).

The Dremel VersaFlame is equipped with a child-safety

mechanism. This mechanism requires a two-step operation to

protect against accidental ignition.

To switch on and operate the Dremel VersaFlame, follow the steps

in Figure 3.

NOTE: The air control lever must be in the open position (Figure

3a). The lock button must be in the forward position for the tool

to be able to ignite (Figure 3b).

1. Hold the Dremel VersaFlame in one hand.

2. With your other hand move the child-safety lock to the left

(Figure 3c).

3. Slowly press the ignition button and hold it down (Figure 3d).

4. When using the catalyst: Close the air control lever for

2 seconds and re-open it to prevent the catalyst from being

overheated (Figure 3e).

NOTE: After ignition, make sure that the tool is switched on

by checking that the catalyst starts to glow.

5. To switch off the Dremel VersaFlame, release the ignition

button. This will immediately shut off the ﬂow of butane gas.

If the Dremel VersaFlame is to be used continuously for a

prolonged period of time, holding down the ignition button can

become uncomfortable. To operate the Dremel VersaFlame

continuously, follow the steps in Figure 4.

1. Switch on the Dremel VersaFlame as described above.

2. Slide the lock button backward (Figure 4a) and release the

ignition button (Figure 4b).

3. To switch off the Dremel VersaFlame, slide the lock button

forward. This will immediately stop the ﬂow of butane gas.

USING WITH AN OPEN FLAME

The Dremel VersaFlame can only be used with an open ﬂame if

the catalyst is removed.

FLAME LENGTH AND

TEMPERATURE ADJUSTMENT

Move the ﬂame control lever forward to increase the ﬂame

length and temperature, or backward to decrease the ﬂame

length and temperature.

When using an open ﬂame, the Dremel VersaFlame is at the

desired temperature immediately after ignition.

Please allow ± 25 seconds of heat-up time for the soldering tip.

USING THE ACCESSORIES

WARNING

ALWAYS SWITCH OFF THE TOOL AND

ALLOW IT TO FULLY COOL DOWN BEFORE

ATTACHING OR REMOVING ACCESSORIES.

The Dremel VersaFlame is delivered with a catalyst, a soldering

tip, a ﬂame extension piece and a deﬂector.

CATALYST (Figure 1 part 2)

The catalyst generates hot air of 680°C: Used for melting

plastics and other heat-sensitive materials.

1. Slide the narrow part of the catalyst into the burner. Make sure

the slot of the catalyst is aligned with the white indicator

mark. See Figure 5.

2. To remove the catalyst, slide it out of the burner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 2200 Versaflame Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info