Bedienungsanleitung Dremel 940 (Seite 5 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

515901

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

GENERAL SAFETY INSTRUCTIONS

WORKING SAFELY WITH THIS UNIT IS

POSSIBLE ONLY WHEN THE OPERATING

AND SAFETY INFORMATION ARE READ

COMPLETELY AND THE INSTRUCTIONS

CONTAINED THEREIN ARE STRICTLY

FOLLOWED.

• If the cable is damaged or cut through while

working, do not touch the cable but immediately

pull the mains plug. Never use the unit with a

damaged cable.

• If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualiﬁ ed persons in order to avoid a

hazard.

• The unit must not be damp and must also not be

operated in damp surroundings.

• For indoor use only.

• Connect units that are used outdoors by means

of a fault current protection switch (FI) with a

maximum triggering current of 30 mA. Use only

an extension cable that is approved for outdoor

use.

• Always direct the cable to the rear away from

the unit.

• For pauses in the work of more than

30 minutes, pull the mains plug.

• This appliance is not intended for use by

persons (including children) with reduced

physical sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

• Children should be supervised to ensure that

they do not play with the appliance.

• Dremel is able to ensure ﬂ awless functioning of

the unit only if the original accessories intended

for it are used.

• Do not work materials containing asbestos

(asbestos is considered carcinogenic).

• Take protective measures when during work

dust can develop that is harmful to one's

health, combustible or explosive (some dusts

are considered carcinogenic); wear a dust

mask and work with dust/ chip extraction when

connectable.

• Do not change nozzles while glue gun is in

"on" position, plugged in, or warm to the touch.

Before changing nozzles, make sure glue gun is

cool to the touch, unplugged, and the switch is

in the "off" position.

ENVIRONMENT

DISPOSAL

The unit, accessories and packaging should be

sorted for environment-friendly recycling.

ONLY FOR EUROPEAN COUNTRIES

Do not dispose of power tools into

household waste! According to the

European Guideline 2002/96/EC for Waste

Electrical and Electronic Equipment and its

implementation into national right, power

tools that are no longer usable must be

collected separately and disposed of in an

environmentally correct manner.

SPECIFICATIONS

GENERAL SPECIFICATIONS

Description: Dremel Glue Gun

Model number 910 920 930 940

Glue temperature

• low (LO)

- 105°C 105°C -

• high (HI) 165°C - 165°C 195°C

Glue stick Ø 7 mm 7 mm 7 mm

11/12 mm

Protection Class /II /II /II /II

EXTENSION CORDS

Use completely unrolled and safe extension cords

with a capacity of at least 5 Amps.

ASSEMBLY

GENERAL

The glue gun is intended for the quick gluing of

clean, dry and grease-free materials with glue

heated to its melting point.

2610399275-GlueGun-EU-0610.indb 510399275-GlueGun-EU-0610.indb 5 3-6-2010 12:47:043-6-2010 12:47:04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 940 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info