Bedienungsanleitung Dremel Trio (Seite 13 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488596

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

MAKE A FEW PRACTICE CUTS

After installing the bit into the tool and adjusting your depth

guide, you should make a few practice cuts with the tool before

attempting an actual job. A few exercises will give you the

necessary practice to make clean, professional cuts.

Step 1: Make certain that the collet nut is securely tightened

before turning the tool on.

Step 2: Hold the tool ﬁrmly and turn the tool ON to your desired

speed.

Step 3: While holding the tool ﬁrmly, insert the bit into the

material at a 45° angle, or 15° for tile (Fig. 11).

Step 4: Slowly plunge the bit to a 90° angle to begin the cut

(Fig. 12). The base guide should be ﬂush to the material

surface. For all materials except when cutting around

outlet boxes in drywall, steer the tool in a clockwise

direction with slow, steady pressure to make the cut.

Step 5: After completing your cut, turn off the tool and carefully

remove it from the material. Do not attempt to use this

tool to make cut-outs around any ﬁxture or opening

which has live electrical wires, or any wall which may

have live electrical wiring behind it, as the bit could

conduct current to the tool, creating an electrocution

hazard for the operator. Shut off breakers or remove

fuses to disconnect the circuit. Always hold the tool

by its thermoplastic housing, and always wear eye

protection when operating the tool.

NOTE: Because of the rotating cutting action of the bit, there will

be a slight pull when cutting. The slower you cut the more control

you have. Excessive pressure or fast cutting will cause excessive

heat and may shorten the life of the bit.

NOTE: When cutting on a vertical surface, avoid ending your cut

at the bottom of the hole. If possible, start and end your cut at

the top so the scrap part will not drop onto the rotating bit. Turn

the tool off and remove it from the material.

USING THE STRAIGHT EDGE/CIRCLE GUIDE

STRAIGHT EDGE

The straight edge guide (optional) is used for cuts parallel to the

edge of the work, and can be used from either side of the base

plate for cutting on the left or right side of the material.

1. Unscrew the base plate thumbscrew; slide the sliding rod

of the straight edge guide through the two notches on the

bottom side of the base plate.

2. Position the tool to the desired length from the edge of your

material. Tighten the thumbscrew (P) to secure the straight

edge guide to the base plate (Fig. 13).

CUTTING LARGE DIAMETER CIRCLES (10 CM DIAMETER)

1. Draw the circle on the work piece and mark the centre of the

circle. Drill a centre hole with the tracer. Make sure the edge

guide is facing UP (Fig. 14).

2. Using the tool, plunge cut a pilot hole on the edge of the circle,

turn tool off and disconnect the plug from power source.

a. To make a hole – cut from inside edge of the circle

b. To make wheels or discs – cut from the outside edge of

the circle

3. Attach straight edge guide to base plate, properly

position base onto straight edge guide to give the desired

circle diameter and lock down by tightening base plate

thumbscrew.

4. Insert plug into power source, hold the tool ﬁrmly, turn tool

on and slowly push the tool forward.

MAINTENANCE

Preventative maintenance performed by unauthorised personnel

may result in misplacing of internal wires and components which

could cause serious hazard. We recommend that all tool service

be performed by a Dremel Service Facility. To avoid injury from

unexpected starting or electrical shock, always turn off power tool

before performing service or cleaning.

CLEANING

WARNING

TO AVOID ACCIDENTS, ALWAYS

DISCONNECT THE TOOL AND/OR CHARGER

FROM THE POWER SUPPLY BEFORE CLEANING. The tool can be

cleaned most effectively with compressed dry air. Always wear

safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean

and free of foreign matter. Do not attempt to clean the tool by

inserting pointed objects through an opening.

WARNING

CERTAIN CLEANING AGENTS AND

SOLVENTS DAMAGE PLASTIC PARTS.

Some of these are: gasoline, carbon tetrachloride, chlorinated

cleaning solvents, ammonia and household detergents that

contain ammonia.

SERVICE AND WARRANTY

WARNING

NO USER SERVICEABLE PARTS INSIDE.

Preventive maintenance performed by

unauthorised personnel may result in incorrect connection of

internal wiring and components which could cause serious

hazard. We recommend that all tool service be performed by a

Dremel Service Centre. SERVICEMEN: Disconnect the tool and/or

charger from the power source before servicing.

This DREMEL product is guaranteed in accordance with statutory/

country-speciﬁc regulations; damage due to normal wear and

tear, overload or improper handling is excluded from the warranty.

In case of a complaint, send the undismantled tool or charger and

proof of purchase to your dealer.

CONTACT DREMEL

For more information on the Dremel product range, support and

hotline, go to www.dremel.com.

Dremel Europe, P.O. Box 3267, 4800 DG Breda, The Netherlands

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel Trio Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info