Bedienungsanleitung Duux Video baby monitor (Seite 21 von 22) (Englisch)

648115

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Why is the battery not lasting long (less than two hours after fully charged)?

To maximize battery usage, please follow these steps:

RESET the unit(s) while getting charged.

Charge the battery for at least 8 hours.

Unplug the power adapter and use the unit(s) on battery power until it shuts down by

itself.

Repeat steps 2 and 3 for 2 more times.

With each charge you will ﬁnd out that the battery will last longer than the previous time. If

you do not use the unit(s) on battery power on a regular basis, we recommend you to use the

unit(s) on battery power until it shuts down on its own at least one a week use, to optimize

battery usage and life.

I installed the micro SD card, why does it still display “No SD card”?

Before installing the micro SD card, please turn oﬀ the parent unit. If you install the micro SD

card in ON mode, please press the RESET button to restart the parent unit.

The parent unit displays multi view (4 cameras). How to change to full screen display mode?

Quickly press the POWER / MULTI / BACK button to exit / enable multi view display.

How come the parent unit does not take any pictures and/or videos?

There is no micro SD card in the receiver unit. Insert an appropriate micro SD card in the

receiver unit.

The memory capacity of the micro SD card inserted is full. Delete any existing recordings

or replace the micro SD card in the receiver unit with a new one.

Why does the baby unit not transmit any audio/video signals?

The sensitivity of the voice activation (VOX) and/or motion detection is set too low. Please

Why does parent unit intermittently displays “Connecting camera #...” error message

and/or a black screen (no video)?

This problem is normally caused by presence of other wireless devices, especially a wireless

network router/adapter or another wireless Audio/Video device using 2.4GHz wireless

frequency.

We suggest to:

Why does the parent unit display “Camera # unavailable” error message?

“Camera # unavailable" message normally appears if you are using a single baby unit (or

only one baby unit is registered) but you have set Auto Scan to a setting other than

"Never".

Why doesn’t my monitor work on rechargeable battery even when the battery charging

level indicator shows battery is fully charged?

If the battery charging level indicator shows battery is fully charged as soon as you plug the

power adapter to the monitor, then it's possible that the battery is not installed properly.

Press the RESET button on the camera to change communication channel between the

units.

Change the wireless channel setting of your router from AUTO to either lower channels

2 or 3 (if that does not help then upper channels 10 or 11) to reduce interference from

wireless network.

If possible, do not keep other wireless devices within 3-5meters from camera and

monitor.



40 41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Duux Video baby monitor Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Duux Video baby monitor

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info