Bedienungsanleitung Dyson Airblade Wash and Dry WD04 (Seite 3 von 160) (Alle Sprachen)

761233

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ROI

Air is continuously running from the

hand dryer. Ensure that the sensors are clean and free

from obstructions.

There is no air coming from the hand dryer. Check that the fuse/circuit breaker is working

and that the power is connected. Must be

performed by a qualified electrician.

Ensure that the air hose is securely

attached to the base of the tap and no

leaks are present. Must be performed by a

qualified electrician.

Check that the sensor cable from the tap is

securely connected. Must be performed by a

qualified electrician.

TAP

Problem Action

Water is continuously coming from the tap. Ensure that the sensors are clean and free

from obstructions.

There is no water coming from the tap. Ensure that the power and water supplies are

turned on and that the isolation valve is open.

Must be performed by a qualified electrician.

Ensure that the aerator is free from debris,

remove and clean/replace if necessary.

The water coming from the tap is overly hot

or cold. Contact the Dyson Helpline.

If you have any further questions please contact the Dyson Helpline.

USE IN FOOD PREPARATION AREAS

For food preparation environments special installation is required, which must fully enclose the

motor bucket and hose in a cleanable housing or have the motor bucket on the reverse side of

a wall, provide adequate clearance for cleaning underneath (if applicable) and be such that the

unit is at least 2.5 metres from uncovered food or uncovered food-contact surfaces.

CLEANING

The hand dryer should be cleaned daily.

Wipe sensors using a soft cloth and non-abrasive cleaner then place cleaning cap over sensors

to prevent air and water from being activated.

Clean all tap surfaces, sink, mirror and any walls or counter tops. When complete REMEMBER

to remove cleaning cap.

REGULARLY clean air inlets on base of motor bucket (under sink). Ensure that the plughole in

sink is free from blockages so water can drain freely.

IMPORTANT INFORMATION

Do not pressure wash the machine.

All cleaning chemicals should be used exactly as indicated by the manufacturer’s instructions

(including appropriate dilution).

If a cleaning product is left on the machine for too long, a film will form. This may reduce the

effectiveness of the antimicrobial surfaces.

Any chemicals intended for use should first be tested on an inconspicuous area to confirm

suitability. Aside from cleaning chemicals, care should be taken to avoid any harmful fluids

from coming into contact with the product, in particular oils and alcohol-based products.

WATER GUIDELINES

This hand dryer has an IP35 certification.

Use of pressure washers can force water inside the casing.

Water damage caused by incorrect cleaning will invalidate your guarantee.

AUTOMATIC DUTY FLUSH

The unit is equipped with a fixed automatic water flush, which activates for 60 seconds

24 hours after last use. This helps reduce water stagnation and bacteria proliferation within

the product.

Please ensure that the unit is always installed over a functional basin with free and

connected drainage.

SOLENOID REPLACEMENT GUIDELINES

It may be necessary to replace the solenoid on your hand dryer. If you suspect that this is the

case, please contact the Dyson Helpline.

When replacing the solenoid, the hand dryer must be disconnected from the mains electricity

and water supply. Failure to do so could lead to serious injury and/or damage to property.

FILTER MAINTENANCE

Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet

with a soft cloth should be sufficient to remove dust and debris.

If the air inlet gets clogged, further cleaning or a filter change might be required.

If required for high usage environments, a Dyson filter change kit provides everything needed

to change your unit’s HEPA filter on site. Contact the Dyson Helpline for more information.

Filter cleaning or replacement for your hand dryer can be carried out by carefully following

the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or

contact the Dyson Helpline for support.

SERVICING

If your hand dryer needs servicing, please call the Dyson Helpline. Also visit the website at

www.dyson.com.

27.11.2017 12:51 - C92757_WD04_OPMAN_INT_X588-OWNERS-MANUAL-PART 3- TEXT.indd_15_0c2s_15_0c2s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dyson Airblade Wash and Dry WD04 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson Airblade Wash and Dry WD04

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info