Bedienungsanleitung Ebode IR Link B (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

611750

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

10-8-2010 5 ebode IR LINK B

Remove the paper backing from one of the IR Emitters, exposing the adhesive surface.

Apply the Emitter directly onto the centre of the sensor “window” on one of your

components.

Note: The Emitters have self-adhesive tape on the back. Use this to stick them onto the IR

eye of your equipment. This should be done very carefully and precisely. Test the position

of the IR Emitters first, before you finally stick them onto the eye.

Step 4: Place a 9 Volt battery (EN22 or PP3) to the battery connector of the IR Hub circuit.

Be sure to observe correct polarity!

ATTENTION: If you are only using one appliance, then you do not need to use the

additional IR Emitters. Never remove these from the wire! Just dress up the wire and leave

close to the Hub.

7. Operation

Normally your ebode IR Link B Receiver will be in a “sleep” mode to maximize battery life.

When in sleep mode, the range between it and your handheld remote is limited to

approx. 4 meter or less.

To activate the system, simply point your remote at the ebode IR Link B IR Receiver from a

nearby location and press one of the buttons. The LED in the front of the receiver will flash

to confirm reception and that the unit is activated to full sensitivity. When activated, the

IR Link B will operate up to a distance of 4 – 8 meters over an angle of ± 30 degrees off

axis. The ebode IR Link B will automatically go back into “sleep” mode after approx. 1

minute.

8. How to avoid and solve possible problems

Although the ebode IR Link B is equipped with proprietary eIR

(pronounced Irex)

Technology, which guarantees a high level of immunity of InfraRed noise of direct sunlight,

CFL lighting and Flat Panel TV’s (including Plasma, LCD and LED), in rare cases, the IR

Receiver may have to be moved to a different location if the unit is picking up

unexpected interference. This interference may, in severe cases, prevent the system from

working. You can identify interference when the InfraRed Emitters are lit or blinking, even

when you’re not using a remote control transmitting at the time.

After repositioning, check to see if the ebode IR Link B operates the satellite Receiver or

other components. If the ebode IR Link B still does not work, reposition the IRED Emitter(s). It

may not be located directly over the component’s InfraRed receiving "window". Consult

the owner's manual of the unit or the manufacturer for the exact location of the InfraRed

"window".

Do you still have questions? Please refer to www.ebodeelectronics.eu

9. Technical information

Power: 9VDC EN22 / PP3 battery (not included)

IR Emitter cable: 3 IR LEDs

Cable length: 3 m, 1 m from IRHUBB to IR LEDs

Receiver dimensions: 55x40x25mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ebode IR Link B Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info