Bedienungsanleitung Elac AM 150 - Active Monitor (Seite 22 von 24) (Deutsch, Englisch)

561009

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Explanatory Note on Specifications 19

On the rear of this manual (respectively attachment) you will find the specifications of your loudspeaker

Specifications include:

- Dimensions Height x Width x Depth (in mm)

- Weight (in kg)

- Principle

- Driver Units: number and type of drivers

- Mains Fuse / Mains Voltage

- Max. Power Consumption, Full Output

- Crossover Frequency

- Frequency Range (in hertz)

- Max. amplifier power

- S/N (A-weighted)

- Inputs

- Input sensivity

- Input impedance

Dimensions refer to the outer dimensions of the loudspeakers.

The Weight indicates the total weight of the loudspeaker without packaging and without accessories (like mains cable etc.)

The Principle describes the acoustical and electrical concept on which the speaker is based on (e.g. closed box or bass reflex, pow-

ered (= with amplifier built-in)

Drive Units give information on the number and type of drivers of a loudspeaker.

The correct Mains Voltage, measured in volts, is necessary for a proper function of your appliance and is provided by your local

power authorities. The mains voltage might vary between the given values. The technical data of the Fuse give the current- and volt-

age values which the fuse should have at the given mains voltages.

Max. Power consumption, full output specifies the power, measured in watts, which is drawn out of the mains when the appliance

works with maximum output levels.

The Crossover Frequency is defined by the built-in (active) crossover network which adapts the overlay between collocated drivers.

The Reproduction Range of a loudspeaker is defined by the upper and lower cut-off frequencies of the SPL frequency response. At

the cut-off frequencies the sound pressure level decreases by 8dB (factor 2.5) as compared to the midrange. Given a standard do-

mestic room, the effective lower cut-off frequency may deviate from standard values due to room resonances.

The Max. amplifier power of an amplifier is also measured in watts and specifies the power which can be reproduced by the amplifier

without any disturbances, like humming, noise or distortions. It is differentiated between the sine power and the pulse power. The sine

power describes the power which the amplifier can reproduce for an endless time theoretically, the pulse power is even higher and

specifies the power for short term signals which can be handled by the amplifier without distortions.

The signal to noise ratio (S/N (A-weighted)) describes the relation between the wanted signal and not wanted signals like noise or

humming. Normally it is measured in dB and is weighted with a curve called “A”-curve which describes the sensitivity of the human

ear.

Inputs lists the available inputs and their connector specifications.

The Input sensitivity is measured in volts normally and lets you know the input voltage which is needed to drive the amplifier to full

level.

The Input impedance is the AC resistance, normally measured in kilo-ohms, which represents the load for the driving pre amplifier.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elac AM 150 - Active Monitor Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info