Bedienungsanleitung Electrolux RM 123E (Seite 5 von 16) (Englisch)

625958

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Alternatively, wooden battens may be screwed to the sides of the recess, from front to back, bearing down

on the top of the cabinet to hold it firmly, as shown at A, fig. 4. Whichever method is used, it must be

possible to remove the refrigerator easily for subsequent servicing purposes. The brackets or battens must

be in a position where they will not restrict the air circulation over the cooling unit; they must not be

positioned across the cabinet over the fins of the condenser of the cooling unit at the rear, otherwise air-

flow will be impaired and performance affected.

Fitting the Upper Ventilator

To fit the upper ventilator, screw a block of wood approx. 25mm (1") square x 66mm (25/e") long, to each

side of the recess, 16mm (5/e") back from the front edge, as shown at B, fig. 4. Secure the ventilator to the

blocks with a screw through the hole provided at each end.

Additional Ventilator

To reduce the amount of heat entering the caravan,

particularly when used in warmer climates, an

additional ventilator (A, fig. 5), may be fitted in the wall

of the vehicle, preferably above the level of the top of

the refrigerator. (The exterior flue venting kit must still

be used).

All surfaces above and adjacent to the flue outlet, and

beside and below the burner housing should be of, or

protected by, metal or other inflammable material.

8. VENT HOLE UNDER REFRIGERATOR

A ventilation hole of not less than 13cm2 (2in2) effective area (40mm or 1 5/8" diameter) must be provided

in the floor below the refrigerator as shown in fig. 5. The hole should lead directly to the outside air through

the floor or wall so that, in the event of a gas leak, it would provide an escape outlet for the heavier-than air

gas. It should not be too close to the burner where draught could affect the flame.

On mobile installations, the vent hole should be shielded against entry of mud etc.., by a deflector as

shown in fig. 5a, fitted underneath with its "closed" end facing the front of the vehicle. The deflector should

be made from a suitable piece of metal, to suit the particular installation.

9. FLUE ARRANGEMENT

Flue Baffle

The flue baffle (4, fig. 10) must be in position in the central tube of the boiler, suspended on its support

wire so that the lower end of the baffle is 75mm (3") above the bottom of the central tube over the burner.

The top end of the baffle support wire is bent into the shape of an "0," and rests horizontally on the top of

the central tube. The baffle is correctly positioned during the manufacture and should not become

displaced during normal use. If the flue baffle is missing or is incorrectly located, the cooling unit will not

operate properly on gas. Any strapping tape used to retain the baffle support wire to the top of the boiler

casing during transit should be removed before installation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Electrolux RM 123E Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info