471185
9
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
Mounting
Before starting to mount the appliance, make sure that no
component is damaged, otherwise contact the dealer and stop
mounting. In addition, read all the instructions below carefully.
Use an air outlet pipe no longer than 5 metres.
Limit the number of curves in the duct since each curve
reduces the suction effectiveness equivalent to 1 linear
metre. (E.g.: if two 90° curves are used, the duct should
be no longer than 3 metres).
Avoid drastic changes of direction.
Use a duct with 150mm diameter constant for the whole
length.
Use a duct made of standard complying material.
Remove the safety shim highlighted in the picture (Fig. 1-
2) at the end of the installation.
In case of failure to observe the instructions above, the
supplier can not be held responsible for capacity or noise
problems and no warranty will be granted.
Before making the hole, make sure that the inside of the
cabinet, near the hood housing area, does not have the
structure of the cabinet or other particulars which may
cause problems for the proper installation. Make sure
that the overall dimensions of the hood and the hob ae
compatible with the cabinet and therefore the installation
is feasible.
Make a 848x100mm rectangular hole on the back of the
hob.
In case of version with motor already mounted, remove
the screws and the suction unit to insert the hood into the
hole made.
Install the hood in the hole made, inserting it from above,
as shown (Fig. 3). In case of version with motor on
board, it is necessary to remove the suction unit before
inserting the product into the cabinet.
Fix the hood inside the cainet using the special brackets
supplied (Fig. 4). Start mounting the brackets in the lower
part of the hood (Fig. 5a) making sure that there is a
distance of 2 mm between the lower part of the bracket
and the cabinet bottom (Fig. 5b). This distance allows
the traction of the product downwards on fixing, (Fig. 5c),
so that the stainless steel frame adheres perfectly on the
worktop.
Before inserting the screws into the cabinet, make sure
that the product is perfectly perpendicular to the worktop.
After completing the installation and connecting the
product to the power supply, lift the hood and remove the
door lock (Fig. 6).
In case of version with motor on board start mounting the
motor unit directing the air outlet to the chosen position
downwards or upwards (Fig. 7b). The motor can be
installed on both the front side and the back one of the
hood. Once the installationof the motor has been
comleted, start mounting the duct for the air outlet.
In case of version with external motor put the suction unit
(external motor) in a suitable area and arrange the air
outlet duct. Start mounting the air outlet duct between the
external motor and the hood. Select the air outlet among
the five possibilities (Fig. 7a) and install the union
supplied.
Put the metal box containing the electronic components
in an easily accessible area for any assistance
operations (Fig. 8), connecting the electric connectors of
the same to the hood: pushbutton panel connector (Fig.
9a), 9-pole connector (Fig. 9b), neon connector (Fig. 9c)
In applications with external motor, connect the cable of
the motor unit to the special connector on the electronic
component box (Fig. 10a) in case an external control unit
SEM7 is used connect the 2-pole connector as well (Fig.
10b)
Connect the product to the power supply
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Elica Adagio wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Elica Adagio

Elica Adagio Bedienungsanleitung - Deutsch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info