Bedienungsanleitung Elica Artica AST (Seite 4 von 7) (Englisch)

471126

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Consult the designs in the front pages referenced in the text

by alphabet letters. Closely follow the instructions set

out in this manual. All responsibility, for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

The cooker hood must be placed at a minimum distance of

50 cm from the cooking plane for electric cookers and 75cm

for gas or mixed cookers.

The hood can be installed above these heights but for

optimum performance it should be installed at the distance

quoted for the appropriate heat source.

Do not tile, grout or silicone this appliance to the wall. Surface

mounting only.

The hood is equipped with a top air outlet B for discharge

of fumes to the outside (Ducting version  exhaust pipe

and pipe fixing clamps not provided).

Should it not be possible to discharge cooking fumes and

vapour to the outside, the hood can be used in the filter

version, fitting an activated carbon filter and the deflector F

on the support (bracket) G, fumes and vapours are recycled

through the top grille H by means of an exhaust pipe

connected to the top air outlet B and the connection ring

mounted on the deflector F (exhaust pipe and pipe fixing

clamps not provided).

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Expansion wall plugs are provided to secure the hood to

most types of walls/ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the

type of wall/ceiling. The wall/ceiling must be strong enough

to take the weight of the hood.

Do not tile, grout or silicone this appliance to the wall.

Surface mounting only.

Installation - Fig. 5

Preliminary information for installation of the hood

Assembling the chimney flue support/bracket (3

parts):

The three parts should be fixed with 4 screws, the support

extension is adjustable and should correspond to the internal

width of the telescopic chimney flue.

Disconnect the hood during electrical connection, by turning

the home mains switch off.

Remove the 2 screws fitted inside the lower part of the

hood at the points in which it is fixed to the suction unit (see

also operation 3 - remove the grease filter/s).

1. Rest the suction unit on a flat surface and thread the lower

part of the hood onto it.

2. Connect the sensor to the small plate on the front of the

suction group (A  the male and female connectors have

an obligatory access) and the lamps (C).

Connect the control panel to the small plate located on

the front of the suction group (B  the male and female

connectors have an obligatory access).

3. Fasten the hood to the suction unit using 8 screws.

4. Using a pencil, draw a line on the wall, extending up to

the ceiling, to mark the centre. This will facilitate

installation.

5. Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must correspond

to the centre line drawn on the wall, and the bottom edge

of the drilling template must correspond to the bottom

edge of the hood: bear in mind that, when installation is

complete, the underside of the hood must be at least 50

cm above the cooker top in the case of electric cookers,

and at least 75 cm above the cooker top in the case of

gas or mixed cookers.

6. Rest the support bracket on the drilling template so that

it coincides with the dotted rectangle, mark the two outer

holes and drill them, remove the drilling template, insert

2 wall plugs and fix the hood support bracket into place

using two 5x45mm screws.

7. Hang the hood on the bracket.

8. Adjust the distance of the hood from the wall.

9. Adjust the horizontal position of the hood.

10.From inside the suction unit, use a pencil to mark the hole

to be used for final fixing of the hood.

11.Remove the hood from the bracket.

12.Drill at the point marked (Ø8mm - see operation 10).

13.Insert 1 wall plug

14.Rest the chimney support bracket G against the wall,

touching the ceiling. Use the support bracket as a drilling

template (the small slot formed on the support must

coincide with the line drawn on the wall as above 

operation 4) and mark 2 holes with a pencil, drill the holes

(Ø8mm), insert 2 wall plugs.

15.Fix the chimney support bracket to the wall using two

5x45mm screws.

16.Hook the hood onto the bottom bracket.

17.Fix the hood into its final position on the wall using one

5x45mm screw (ABSOLUTELY ESSENTIAL).

18.Connect a pipe (pipe and pipe clamps not provided, to

be purchased separately) for discharge of fumes to the

connection ring located over the suction motor unit.

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, fix deflector F to the chimney support bracket

G using 4 screws, and connect the other end of the pipe

to the connection ring on deflector F.

19.Make the electrical connections.

20.Apply the chimney stacks and fasten them at the top to

the chimney support G (20b) using 2 screws (20a).

INSTRUCTION ON MOUNTING AND USE GB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Artica AST Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info